ap-3-12.dvi Acta Polytechnica Vol. 52 No. 3/2012 Explosion Cladding of Lead on Steel Milan Turňa1, Jozef Ondruška1, Zuzana Turňová1 1 Slovak University of Technology, Faculty of Materials Science and Technology, J. Bottu 25, 917 24 Trnava, Slovakia Correspondence to: milan.turna@stuba.sk Abstract This work deals with explosion cladding of lead on steel. The welded materials and the Semtex S type explosive are characterised. The preparation of the welded materials and the proposed welding assembly are described. The welding parameters, the welding conditions and the fabrication of the weld overlays are discussed. The quality of the fabricated bimetals was studied by optical and electron microscopy and by mechanical tests. Keywords: lead, structural carbon steel, explosion cladding. 1 Introduction As it is well known, fusion welding, soldering and thermal cutting of lead, including metals combined with lead, is at present prohibited in technical prac- tice. In some cases, however, the use of lead is pos- sible and/or unavoidable. Obvious examples are in the military and chemical industries. Bimetals of lead and other structural materials are interesting for the chemical industry. Bimetals such as Pb — structural carbon steel are attractive mainly owing to the high corrosion resistance of lead and the suf- ficient strength of steel. These bimetalsare used for fabricating vessels for storing dangerous materials, e.g. H2SO4 90 %, H2SO4 60 %, PSCl3 95 %, PCl3, NaNO3. For storing aggressive media a lead layer on steel 3–5 mm in thickness is used depending on the corrosive medium. Until recently the interior of the chemical vessels was first tinned, and then a Pb layer was deposited on it. This procedure posed a great health risk for the persons performing the operations even resulting in occupational diseases. To avoid this kind of risk solid state surfacing, namely by explosion cladding, has been selected as a more suitable tech- nology. 2 Experimental The materials selected for our experiments were as follows: 99.95% lead by STN 42 3701, and the steel type 11 373 by STN 42 5340, S235JRG1 by EN 10025A1. Owing to its low melting point, lead is used with working temperatures only from 150 to 170 ◦C. Only technically pure lead is used in the chemical in- dustry as pure lead has the highest resistance against corrosion. The chemical resistance of lead in some environments may be increased by the addition of a small amount of H2SO4 to provide a protective layer on the material surface. So-called “hard lead” is not suitable for welding, since it causes embrittlement of welded joints. The chemical composition of the welded materials is shown in Tables 1 and 2. Table 1: Chemical composition of Pb 99.95 Pb 99.95 by STN 42 3701 [wt.%] Pb Ag Bi Cu Sb As Fe Zn Sn min. max. max. max. max. max. max. max. max. 99.95 0.001 5 0.030 0.001 5 0.005 0.002 0.002 0.002 0.002 Table 2: Chemical composition of steel type 11 373 Steel type 11 373 by STN 42 5340 [wt.%] C N P S – max. 0.170 max. 0.007 max. 0.045 max. 0.045 – 101 Acta Polytechnica Vol. 52 No. 3/2012 Table 3: Physical properties of lead Physical properties of Pb 99.95 Density ρ [kg · m−3] 11 341 Elasticity modulus in tension E [MPa] (14.71 to 17.65)·10−3 Elasticity modulus in shear G [MPa] 6.865 · 10−3 Sound propagation velocity v [m · s−1] 1 200 Table 4: Mechanical properties of steel type 11 373 Selected mechanical properties of steel type 11 373 Yield point Rp0.2 [MPa] 225 Ultimate tensile strength Rm [MPa] 363 to 441 Minimum ductility A5 [%] 25 Table 5: Cladding parameters (charge thickness H, explosive density ρ, detonation velocity vd, distance spac- ing h, setting angle of accelerated metal [◦], deviation angle of accelerated metal [◦], collision velocity vk, final velocity v0) No. H P vd h α ϑd vk V0 Expl. [mm] [g · cm−3] [m · s−1] [mm] [◦] [◦] [m · s−1] [m · s−1] type 1 31.6 0.980 1 336 5.1–9.8 2.23 8.6–8.9 1 060–1070 207 SP-14 2 31.5 0.984 1 340 7.5 0 8.8 1 340 208 SP-14 3 50.8 1.090 1 454 7.2 0 12.6 1 454 343 SP-14 4 50.7 1.110 1 474 7.0–13.1 2.80 12.7–13.5 1 210–1230 351 SP-14 5 51.7 1.030 1 390 8.0–17.5 4.35 12.5–13.1 1 040–1050 320 SP-14 6 51.5 1.260 1 250 8.0–17.5 4.35 – – – SN-12 7 51.8 1.250 1 250 8.8–18.0 4.26 – – – SN-12 8 21.6 1.156 1 990 4.9–22.7 8.10 9.1–9.6 1 070–1080 332 S-25 Figure 1: Parts of the Fe–Pb binary diagram The physical and mechanical properties of Pb and steel needed for the welding process are presented in Tables 3 and 4. The parameters of the cladding process are given in Table 5. Prior to welding, it was necessary to make a de- tailed study of the Pb — steel binary diagram, and to ascertain the possibility that undesired phases might be formed (Figure 1). All materials to be explosion welded must be free from impurities and organic deposits, irrespective of the cleaning effect of cleaning agents. The weld sur- faces on steel were machined by grinding to rough- ness Ra = 3.2 μm, and shortly before welding they 102 Acta Polytechnica Vol. 52 No. 3/2012 Figure 2: Scheme of the peel test Figure 3: Shear test of the bimetal were degreased with acetone. The lead was straight- enedprior to welding, cleaned with a steel brush and degreased with acetone. The welding parameters are given in Table 5. The explosives for explosion welding do not form a unified group. They need to have specific properties for each technological process. To achieve good process repro- ducibility, the explosive that is used needs to have a stable detonation regime in non-sealed charges. Loose Semtex S type explosives were used for fab- ricating Pb — steel bimetals. These explosives were manufactured at RIICH Synthesia, Pardubice. After welding, the bimetals were cleaned from detonation products with a brush under running water and were then prepared for further study. The following assessment methods were applied for our study of the quality of the fabricated bimetal joints: ultrasonic defectoscopy, mechanical tests, cor- rosion resistance tests and metallographic investiga- tion. 2.1 Ultrasonic defectoscopy The inspection was performed from the lead side. Probe coupling was ensured by the use of oil. The tests were performed usingthe USIP 11equipment with a MSEB 6H probe with 6 MHz frequency. No defects were found in the joint boundary zone. The initial 3.2 mm thickness of the lead plate was reduced to 2.8 to 3.0 mm owing to the high detonation veloc- ity and compression. 2.2 Mechanical tests The quality of the fabricated joints was assessed by the following mechanical tests: a peel test, a shear strength test, and a bend test. Peel test: an ordinary shop hydraulic press was used for this test. It must be stated that this test is not standardised and therefore it serves only to provide information on the boundary quality. The scheme of the test specimens is shown in Figure 2. The test showed that the boundary remained undam- aged and the punch penetrated through the lead. Shear strength test: three specimens with dimen- sions as shown in Figure 3 were cut from the bimetals in the direction of detonation wave propagation. Fail- ure of the specimens occurred on the lead side. This suggests that the lead — steel boundary is of higher strength than the pure lead, thus proving sufficient joint strength. The tensile strength of the initial lead used for cladding was determined to be 12.8 MPa. The bend test is presented in Figure 4. Similar specimens to those used for the tensile test were ma- chined from the fabricated bimetal. The specimen was firmly clamped in a vice and its free end was bent by 180◦ around a mandrel of �14 mm in diame- ter. The specimen was placed in such a manner that the notch face included a 30◦ angle with the normal plane. The boundary was so strong that no dam- age occurred even when the mandrel diameter was reduced to �8 mm. Figure 4: Scheme of the bend test of the bimetal 103 Acta Polytechnica Vol. 52 No. 3/2012 2.3 Metallographic assessment of the welded joints Observation by optical microscopy showed that the basic structure of the steel was polyhedral, locally deformed on the boundary. The thickness of the de- formed layer was around 0.5 mm. The measured wave amplitude was 0.08 to 0.1 mm, and the waving period was 0.48 to 0.53 mm. The weld boundary is shown in Figures 5 to 8. Figure 5: Weld boundary of the lead — steel bimetal 110× Figure 6: Weld boundary of the lead — steel bimetal 600× A more detailed assessment of the character of the fractured surfaces of a Pb — steel welded joint was performed by scanning electron microscope (SEM). The specimens from which the lead was torn off in the peel test were observed. It was observed that fail- ure occurred after preliminary plastic strain, mostly by ductile fracture. Figures 7 and 8 show the ductile fractures in the lead which progressed to the darker zones where insufficient bonding of materials was ob- served. The bonding of Pb to the parent steel mate- rial was around 55 %. Figures 7 and 8 show the fractures after fusing down of Pb from the steel surface in a vacuum. Figure 7: Ductile fracture in the lead (REM) 500× Figure 8: The lead fused from the steel surface 500× 3 Conclusions The aim of our study was to develop and test a special technology for lead cladding on a steel plate made of structural carbon steel. A total of 8 bimetallic welded joint swith dimensions of 120×120×14 mm were fab- ricated. On the basis of our results it can be stated: Sound welded joints were fabricated by explosion cladding with optimum parameters. A new explo- sive was tested and it was found to be suitable for cladding the lead. Mechanical testing (a peel test, a shear test, and a bend test) of the bimetals proved their high quality. The failure of the specimens oc- curred on the lead side during the shear test. The boundary was so strong that no damage occurred 104 Acta Polytechnica Vol. 52 No. 3/2012 even when the mandrel diameter was reduced to �8 mm in the bend test. The peel test showed that the boundary remained undamaged and the punch penetrated through the lead. On the basis of our experience and results it may be stated that this technology is promising one for fabricating bimetals. It is important to emphasize that the technology we have developed posseses no health hazards unlike the risky process of lead sur- facing by flame. Acknowledgement This work was realised with support from GA VEGA MŠ VVŠ SR and SAV. Projects No. 1/2594/12. References [1] Turňa, M., Špeciálne metódy zvárania (Special welding methods). Bratislava : ALFA, 1989. ISBN 80-05-00097-9. [2] Farba, L’: Návrh technológie navárania olovom funkčných plôch chemických nádob. Bratislava : SjF SVŠT, 1985. [3] Available on: http://www.explozia.cz [4] Škorvánková, A.: Posúdenie vhodnosti navárania olova na ocěl explóziou (Feasibility study of ex- plosion cladding of lead on steel). Bratislava : SjF SVŠT, 1986. [5] Turňa, M.: Zváranie kovov v pevnom stave (Solid state welding of metals). Lectures delivered at IWE, FS ČVUT Prague, 2010. [6] Shane, A. H.: Welding Fume in the Workplace. Available on: http://www.aiha.org/localsections/ html/NTS/0602News1.pdf [7] Gul’bin, V. N., Krupin, A. V., Pashukov, Y. N., Yarutich, T. Y.: Examination and Development of Technology for Explosion Welding Lead — Titanium Anodes. Welding International, 1996, Vol. 10, No. 8, p. 647–648. 105