Acta Polytechnica doi:10.14311/AP.2014.54.0320 Acta Polytechnica 54(5):320–324, 2014 © Czech Technical University in Prague, 2014 available online at http://ojs.cvut.cz/ojs/index.php/ap STRUCTURING OF DIAMOND FILMS USING MICROSPHERE LITHOGRAPHY Mária Domonkosa, b, ∗, Tibor Ižáka, Lucie Štolcovác, Jan Proškac, Pavel Demoa, b, Alexander Kromkaa a Institute of Physics, Academy of Sciences of the Czech Republic v.v.i., Cukrovarnická 10/112, 162 53 Praha, Czech Republic b Department of Physics, Faculty of Civil Engineering, Czech Technical University in Prague, Thákurova 7, 166 29 Praha 6, Czech Republic c Department of Physical Electronics, Faculty of Nuclear Sciences and Physical Engineering, Czech Technical University in Prague, Břehová 7, 115 19 Praha, Czech Republic ∗ corresponding author: domonkos@fzu.cz Abstract. In this study, the structuring of micro- and nanocrystalline diamond thin films is demonstrated. The diamond films are structured using the technique of microsphere lithography followed by reactive ion etching. Specifically, this paper presents a four-step fabrication process: diamond deposition (microwave plasma assisted chemical vapor deposition), mask preparation (by the standard Langmuir-Blodgett method), mask modification and diamond etching. A self-assembled monolayer of monodisperse polystyrene (PS) microspheres with close-packed ordering is used as the primary template. Then the PS microspheres and the diamond films are processed in capacitively coupled radiofrequency plasma using various plasma chemistries. This fabrication method illustrates the preparation of large arrays of periodic and homogeneous hillock-like structures. The surface morphology of the processed diamond films is characterized by scanning electron microscopy and with the use of an atomic force microscope. The potential applications of these diamond structures in various fields of nanotechnology are also briefly discussed. Keywords: nanostructuring, diamond thin films, polystyrene microspheres, reactive ion etching, scanning electron microscopy. 1. Introduction 1.1. Diamond and its applications The most commonly used methods for synthesiz- ing diamond are high-pressure, high temperature (HPHT) [1] and chemical vapour deposition methods (CVD) [2]. Other methods include explosive forma- tion (forming detonation nanodiamonds), sonication of graphite solutions (ultrasound cavitation), laser ablation, etc. Due to a unique combination of proper- ties (e.g. extreme hardness, high thermal conductivity, wide band gap, negative electron affinity, high mechan- ical strength, chemical inertness, resistance to particle bombardment, and biocompatibility) diamond is a promising material for applications in various fields of electronics, bioelectronics, sensorics, etc. [3]. The potential applications of diamond depend not only on its intrinsic physical and chemical properties, but also on its surface geometry. The defined surface structuring allows these unique properties to be tuned and exploited for a wider range of applications. For example, structuring of films enhances the surface-to- volume ratio and therefore increases the sensitivity and other performances of fabricated devices [4]. For example, increasing the surface area-to-volume ratio of diamond films improves the field-emission proper- ties by introducing the enhancement effect of the local field near the tips [5]. Generally, various nanostruc- tures can be fabricated from diamond films known as nanowires, nanorods, nanoneedles, etc. Therefore, there is still great interest in developing methods for obtaining diamond nanostructures with high area den- sity, high aspect ratio (depth/width), good uniformity and controlled geometry over large areas [6]. 1.2. Structuring of diamond films On the basis of the fabrication or structuring method, two basic concepts can be defined as: a) the bottom- up strategy and b) the top-down strategy. For struc- turing diamond films, the bottom-up strategy (e.g. selective area deposition [7]) is rarely used because of the greater complexity and low process reliability. Wet chemical etching is not applicable due to the high- temperature stability, super hardness and chemical inertness of diamond. Among the top-down strate- gies, only dry reactive ion plasma etching through a mask can be used. The advantages are greater re- liability, greater reproducibility, and a broad family of possible masking materials (metals, polymers, ox- ides or nitrides) than when the bottom-up strategy is used. The mask, which defines the required geomet- rical patterns, is formed using standard lithographic processes (photolithography, electron beam lithogra- 320 http://dx.doi.org/10.14311/AP.2014.54.0320 http://ojs.cvut.cz/ojs/index.php/ap vol. 54 no. 5/2014 Structuring of Diamond Films Using Microsphere Lithography Steps Process parameters 1a) MCD deposition MW power 3000 W total gas pressure 7000 Pa CH4/H2 5 % CO2/H2 1.5 % temperature 800 °C process time 4 h (pre-deposition: 2 % of CH4/H22 without CO2 for 10 min) 1b) NCD deposition MW power 3000 W total gas pressure 7000 Pa CH4/H2 5 % CO2/H2 1.5 % temperature 800 °C process time 3 h (pre-deposition: 2 % of CH4/H2 without N2 for 10 min) 2a) RIE process RF power 100 W (O2-plasma) total pressure 12 Pa O2 flow rate 50 sccm (for 7 min) self-bias voltage −57 V 2b) RIE process RF power 100 W (CF4/O2-plasma) total pressure 12 Pa (1.) O2 flow rate 50 sccm (for 2 min) (2.) O2/CH4 flow rate 40/10 sccm (for 8 min) self-bias voltage −57 V Table 1. Process parameters for CVD diamond deposition and diamond etching using the PS template as a direct mask (for PS1500). phy, nanoimprinting, etc.). However, these processes are expensive or time-consuming. A possible mask preparation process would involve utilizing a mono- layer of plasma-treated microspheres with controllable size and gap. In this study, we present structuring of diamond thin films using the technique of microsphere lithography. 2. Experimental section A schematic illustration of the main technological steps for diamond structuring is shown in Fig. 1: (1.) Diamond deposition. Two types of diamond films were grown in a focused microwave chemical vapor deposition reactor (Aixtron P6) on a silicon substrate 1 × 1 cm2 in size (for the plasma parame- ters see rows 1 and 2 in Table 1). (2.) PS mask preparation. Uniform periodic ar- rays of polystyrene (PS) microspheres were achieved by the standard Langmuir-Blodgett method, i.e. self-assembly of microspheres in a hexagonally close- packed monolayer at the water-air interface. The initial diameter of the PS microspheres was 1500 nm. Details abouth the preparation of the mask can be found in ref. [8]. (3.) Mask modification – PS etching. The prepa- ration of the hexagonally close packed monolayer Figure 1. Schematic drawing of diamond film struc- turing using a PS microsphere array. was followed by reactive ion etching. The PS mi- crospheres were modified in a capacitively coupled plasma system (CCP-RIE, Phantom III, Trion Tech- nology) in an oxygen atmosphere (for the etching parameters see Table 1, row 3). (4.) Diamond etching. The samples were subse- quently also treated by the CCP-RIE system. Two different gas mixtures were used: pure O2 and 20 % of CF4 in O2 gas (see row 4 in Table 1). 321 M. Domonkos, T. Ižák, L. Štolcová et al. Acta Polytechnica Figure 2. Top-view SEM and AFM (2 × 2 µm) images of a), c) MCD and b), d) NCD diamond thin films before the mask was prepared. Figure 3. Raman spectra of a) MCD and b) NCD films measured by an excitation wavelength of 325 nm. The plasma parameters were chosen on the basis of our previous study on PS and diamond etching [9, 10]. The samples were systematically characterized after each technological step. The morphology of the CVD grown and plasma etched samples was characterized by scanning electron microscopy (SEM, e_LiNE writer, Raith GmbH) and with the use of an atomic force microscope (Veeco Dimension 3100, NTMDT Ntegra). Raman spectroscopy (Renishaw inVia Reflex) with an excitation wavelength of 325 nm was employed to determine the chemical character (i.e. sp3 versus sp2 carbon bonds) of the diamond films. 3. Results and discussions Figure 2 shows the surface morphology and the to- pography of the diamond films before the mask was prepared, taken by scanning electron microscopy. The diamond film with larger grain sizes (∼ 1 µm) was labelled as MCD (microcrystalline, Fig. 2a), and the diamond film with smaller grain sizes (< 50 nm) was labelled as NCD (nanocrystalline, Fig. 2a). Both dia- mond films were about 3 µm in thickness. Figure 2c,d shows the 3D topography of the diamond films (before the mask was prepared), provided by an atomic force microscope (AFM). The Raman spectra clearly confirmed the diamond character in both films (Fig. 4a,b). For the MCD film, the spectrum is dominated by a sharp peak located at 1332 cm−1, which is the characteristic line for the phonon mode of the sp3 crystalline diamond phase. Two broad bands located at frequencies ∼ 1374 cm−1 and ∼ 1575 cm−1 are attributed to the D-band (de- fects) and to the G-band (graphite), which represents the non-diamond carbon bonds (sp2 phase). A weak band centered at ∼ 1154 cm−1 corresponds to the trans-polyacetylene-like groups at the grain bound- aries [11]. This band is more intensive for NCD films, where the crystals are much smaller, and more sp2 carbon bonds are present at grain boundaries. Thus, 322 vol. 54 no. 5/2014 Structuring of Diamond Films Using Microsphere Lithography Figure 4. Tilted-angle view (45°) SEM images of etched MCD diamond films (columns 1, 2) and NCD diamond films (columns 3, 4) prepared using a PS microsphere mask (PS 1500 nm) by etching in oxygen plasma (a, c, e, g) and with the addition of CF4 (b, d, f, h). (Note: the upper row and the bottom row differ only in magnification). the intensity of the G-band increases and the intensity of the diamond-peak (at 1332 cm−1) decreases, but it is still resolvable in the Raman spectrum. Right at the beginning of the plasma treatment (step 2a in Table 1) we observed homogeneous etching of PS over the whole sample. The close-packed arrays of PS microspheres were converted into a non-close- packed template with the preserved period of the initial microsphere array (not shown here) [10]. The surface morphology of the diamond films after the CCP-RIE processes (step 2a and 2b, Table 1) is shown in figure 4. Periodic hillock-like structures with a period of ∼ 1500 nm were observed. Their height was estimated from the AFM image to be ∼ 600 nm for MCD and ∼ 800 nm for NCD. The fabricated hillock-like features were better recognized (i.e. their geometrical border was better defined) for the NCD films. This is attributed to the nanocrystalline char- acter itself. In the case of MCD films, the fabricated structures reveal non sharp edges (borders), which we assign to the different etching rates for each crys- tal facet of the diamond. This means that the (111) facets were etched at different rates than the (100) oriented diamond crystals, etc. [12]. The MCD films consist of randomly and well faceted crystals and the surface roughness is higher for the thicker films. From this point of view, the NCD films do not reveal such dependences or nonhomogenities on the microscopic scale, i.e. the grain size and the surface roughness do not vary with the film thickness. The surface of the etched MCD and NCD films in pure oxygen plasma (columns 1 and 3 of Fig. 4) cor- responds well to our previous studies [9]. RIE etching in O2 led to the formation of diamond needle-like structures (or so-called whiskers). The main reason for this effect is that the ions are vertically accelerated to the substrate and not only chemical etching but also physical sputtering takes place. Moreover, it is well-known that oxygen etches sp3 diamond bonds much faster than sp2 carbon bonds [13], resulting in the formation of needle-like structures. In NCD films, more sp2 carbon bonds at the grain bound- aries correspond to the formation of needle-like struc- tures [14].However, the addition of CF4 into O2 re- sulted in flattening/smoothing of the diamond surface. 4. Conclusion In summary, we have demonstrated that microsphere lithography is a promising technique for structuring diamond thin films in the so-called top-down strategy. Diamond films were grown using a focused microwave plasma CVD process, and their crystallographic char- acter was controlled by the gas mixture that was used. The MCD films were grown from a CO2 + CH4 + H2 gas mixture, and the NCD films were grown from a N2 + CF4 + H2 gas mixture. Self-assembled, hexag- onally close packed PS microsphere arrays obtained by the Langmuir-Blodgett method were used as the masking material. First, the PS layer was treated in plasma to predefine the final geometry of the dia- mond structures. During continued plasma etching, the primary PS were removed. Using this cost-effective and time-efficient method, highly periodic and homogeneous hillock-like struc- tures were achieved both for MCD films and for NCD films. It is believed that diamond structures fabricated over large areas will have a positive impact on their further applications as photonic crystals in optics or as active functional surfaces in sensorics, bioelectronics, biomedicine and electrochemistry. 323 M. Domonkos, T. Ižák, L. Štolcová et al. Acta Polytechnica Acknowledgements This work was supported by grants from the Czech Science Foundation P108/12/G108 (T. I., A. K.). The work was carried out in the framework of the LNSM infrastructure. References [1] Bundy, F.P. et al.: Man-Made Diamonds. Nature, 176, 1955, pp. 51–54. doi:10.1038/176051a0 [2] May, P.W.: Diamond thin films: a 21st-century material. Philos. Trans. R. Soc. Lond. Ser. Math. Phys. Eng. Sci., 358 (1766), 2000, pp. 473–495. doi:10.1038/176051a0 [3] Koizumi, S. et al.: Physics and applications of CVD diamond. Weinheim: Wiley-VCH, 2008. doi:10.1002/9783527623174 [4] Babchenko, O. et al.: Nanostructuring of diamond films using self-assembled nanoparticles. Cent. Eur. J. Phys., 7 (2), 2009, pp. 310–314. doi:10.2478/s11534-009-0026-8 [5] Uetsuka, H. et al.: ICP etching of polycrystalline diamonds: Fabrication of diamond nano-tips for AFM cantilevers. Diam. Relat. Mater., 17 (4-5), 2008, pp. 728–731. doi:10.1016/j.diamond.2007.12.071 [6] Demo, P. et al.: Analytical approach to time lag in binary nucleation. Phys. Rev. E, 59 (5), 1999, pp. 5124–5127. doi:10.1103/PhysRevE.59.5124 [7] Babchenko, O. et al.: Toward surface-friendly treatment of seeding layer and selected-area diamond growth. Phys. Status Solidi B, 247 (11-12), 2010, pp. 3026–3029. doi:10.1002/pssb.201000124 [8] Stolcova, L. et al.: Periodic arrays of metal nanobowls as sers-active substrates. NANOCON 2011. Brno: TANGER, 2011, pp. 737–741. [9] Domonkos, M. et al.: Mask-Free Surface Structuring of Micro- and Nanocrystalline Diamond Films by Reactive Ion Plasma Etching. Adv. Sci. Eng. Med., 6 (7), 2014, pp. 780–784. doi:10.1166/asem.2014.1573 [10] Domonkos, M. et al.: Controlled Structuring of Self-assembled Polystyrene Microsphere Arrays by Two Different Plasma Systems. NANOCON 2013. Brno: TANGER, 2013, p. 34–38. [11] H. Kuzmany, R.P.: The mystery of the 1140 cm −1 Raman line in nanocrystalline diamond films. Carbon, 42 (5), 2004, pp. 911–917. doi:10.1016/j.carbon.2003.12.045 [12] Neves, A.J., Nazaré, M.H.: Properties, Growth and Applications of Diamond. IET, 2001. [13] Wang, Q. et al.: Chemical gases sensing properties of diamond nanocone arrays formed by plasma etching. J. Appl. Phys., 102 (10), 2007, p. 103714. doi:10.1063/1.2817465 [14] Zou, Y.S. et al.: Fabrication of diamond nanopillars and their arrays. Appl. Phys. Lett., 92 (5), 2008, p. 053105. doi:10.1063/1.2841822 324 http://dx.doi.org/10.1038/176051a0 http://dx.doi.org/10.1038/176051a0 http://dx.doi.org/10.1002/9783527623174 http://dx.doi.org/10.2478/s11534-009-0026-8 http://dx.doi.org/10.1016/j.diamond.2007.12.071 http://dx.doi.org/10.1103/PhysRevE.59.5124 http://dx.doi.org/10.1002/pssb.201000124 http://dx.doi.org/10.1166/asem.2014.1573 http://dx.doi.org/10.1016/j.carbon.2003.12.045 http://dx.doi.org/10.1063/1.2817465 http://dx.doi.org/10.1063/1.2841822 Acta Polytechnica 54(5):320–324, 2014 1 Introduction 1.1 Diamond and its applications 1.2 Structuring of diamond films 2 Experimental section 3 Results and discussions 4 Conclusion Acknowledgements References