Acta Polytechnica doi:10.14311/AP.2015.55.0150 Acta Polytechnica 55(3):150–153, 2015 © Czech Technical University in Prague, 2015 available online at http://ojs.cvut.cz/ojs/index.php/ap POLYMERS CONTAINING Cu NANOPARTICLES IRRADIATED BY LASER TO ENHANCE THE ION ACCELERATION Mariapompea Cutroneoa, ∗, Lorenzo Torrisib, Anna Mackovaa, c, Andriy Velyhand a Nuclear Physics Institute, ASCR, 25068 Rez, Czech Republic b Physics Department and of Earth Sciences, Messina University, V.le F.S. d’Alcontres 31, 98166 S. Agata, Messina, Italy c Department of Physics, Faculty of Science, J.E. Purkinje University, Ceske mladeze 8, 400 96 Usti nad Labem, Czech Republic d Institute of Physics, ASCR, v.v.i., 182 21 Prague 8, Czech Republic ∗ corresponding author: cutroneo@ujf.cas.cz Abstract. The Target Normal Sheath Acceleration method was employed at PALS to accelerate ions from laser-generated plasma at intensities above 1015 W/cm2. Laser parameters, irradiation conditions, and target geometry and composition control the plasma properties and the electric field driving the ion acceleration. Cu nanoparticles deposited on the polymer promote resonant absorption effects, increasing the plasma electron density and enhancing the proton acceleration. Protons can be accelerated in the forward direction at kinetic energies up to about 3.5 MeV. The optimal target thickness, the maximum acceleration energy and the angular distribution of the emitted particles were measured using ion collectors, an X-ray CCD streak camera, SiC detectors and a Thomson Parabola Spectrometer. Keywords: TNSA, hydrogenated target, resonant absorption. 1. Introduction In a laser-matter interaction, the electromagnetic en- ergy of the laser radiation is converted initially into electronic excitation and later into thermal, chemical and kinetic energy [1]. The characteristics of the laser- generated plasma, the amount of emitted ions and their distribution into energy, charge states and angle emission depend on many important factors. The propagation of the ions in forward direction and in backward direction, for example, is tied to the thick- ness of the target [2]. The focal position and the laser pulse duration have a crucial role on the characteris- tics of the generated plasma [3]. The laser intensity is the main factor influencing the ion distribution of the energy and the charge state [4]. The mechanisms for ion generation, acceleration and expansion in a vacuum, are complex. Above the ablation thresh- old, and at laser intensity higher than 1015 W/cm2, plasma may be full ionized, and non-linear effects, ponderomotive forces, relativistic electrons and mag- netic self-focusing effects promote high charge states and accelerate the emitted ions [5]. Using the target normal sheath acceleration (TNSA) regime, in which a double layer of charges generated in the rear side of the foil drives the ion acceleration in the forward di- rection, along the normal to the target surface, charge states may reach 60+ and ion acceleration values may be higher than 1 MeV per charge state [6]. A plasma rich in protons, carbon and copper ions can be ob- tained by irradiating thin polyethylene foils covered by Cu films or containing Cu nanostructures. The composition and the geometry of the target absorb high laser energy and generate hot plasmas and high charge separation, inducing high ion acceleration, as will be reported. In this context, investigations into optimal laser parameters and irradiation conditions will be aimed at maximizing the ion kinetic energy. 2. Material and Methods The high-power photodissociation iodine laser system of the PALS Research Center in Prague, operating at 1.315 µm wavelength, laser energy ranging between 450 and 600 J, pulse duration 300 ps, and intensity of 1015 W/cm2, was employed for the experiments pre- sented here [7]. The focalization setting of the laser beam consists in an aspherical lens (f = 627 mm for 1 ω) 29 cm in diameter focusing the laser beam on to the target with a nominal spot of 70 µm. Sheets of pure Mylar, pure Copper, and Mylar covered by thin Cu films were irradiated at 30° with respect the normal to the target surface. The original stoichiom- etry of the Mylar or polyethylene terephthalate is (C10H8O4)n. The thickness of the mylar ranges be- tween 0.6 µm and 100 µm, and the thickness of the Cu film ranges between 0.01 µm and 1 µm. The tar- gets were produced by the physical vapor deposition (PVD) method, using a Leybold-Heraeus evapora- tor, at a vacuum of 10−6 mbar. A mylar substrate, 0.6 µm in thickness was covered by the evaporated Cu thin film, the thickness of which was measured online, with a calibrated quartz crystal, and offline, using the transmission energy loss spectroscopy of the 241Am 150 http://dx.doi.org/10.14311/AP.2015.55.0150 http://ojs.cvut.cz/ojs/index.php/ap vol. 55 no. 3/2015 Polymers Containing Cu Nanoparticles Figure 1. Experimental setup. alpha source. At very low thicknesses, of the order of 5–10 nm, the Cu film is not uniform; it consists of nu- cleated Cu cluster with dimensions comparable with the thickness, as observed at SEM. The laser beam was focused 100 microns in front of the the target surface (FP = −100 µm) [8]. The scattering chamber is equipped with a target holder movable in x, y, z di- rections with 1 µm minimum steps [7]. A KENTECH X-ray streak camera, fixed in a side view having 2 ns exposition time, is employed to monitor the initial position of the plasma formation. Ion collectors (IC) and SiC semiconductors are employed in time-of-flight (TOF) configuration for the ion detection at an angle of 30° and at a distance of 1.03 and 0.6 m from the target [9]. SiC is a promising detector not sensitive to the visible, soft UV, and infrared light, where op- tical photons are not able to produce electron-hole pairs because their energies are below the 3.2 eV of the 4H-SiC gap energy. The photons, electrons and ions absorbed in the sensitive volume of the detector generate e-h pairs, losing 7.8 eV for a pair production, which results in voltage signal at the device electrodes proportional to the deposited radiation energy [10]. A Thomson Parabola Spectrometer (TPS) was placed in forward direction at 0° angle and 1.67 m distance from the target [11]. TPS consists in a magnetic-electrostatic system; it is equipped with two input pin-holes, 1 mm and 0.1 mm in diameter. The emitted ions undergo a magnetic deflection of about 0.1 T and an electrostatic deflection voltage of the order of 3 kV. The trajectories of the emerging are parabolic. They are detected on a plane orthogonal to the incident ions by a Multi-Channel Figure 2. SiC spectra for irradiation of pure mylar (a) and of irradiation of mylar covered with a layer of Cu 10 nm in thickness (b), 50 nm in thickness (c) and 100 nm in thickness (d). Plate (MCP) coupled to a phosphorus screen and a CCD camera. the recorded spectra were stored into a fast oscilloscope operating at 20 GS/s. A schematic view of the experimental arrangement is shown in Fig. 1. 3. Results and Discussion The SiC spectra of ions accelerated by a laser irradiat- ing mylar and Cu are presented in Fig. 2. Irradiating a pure mylar thin film, 8 µm in thickness, with 471 J pulse energy and −100 µm focal position, the kinetic energy of faster protons is 0.9 MeV (a). Due to the conditions of the focal position, this relatively high proton energy is controlled accurately by the streak camera. At the value used here, self-focusing may be induced, decreasing the laser spot on the target and increasing the laser intensity [4]. However the laser energy released in the thin mylar remains low because the pure mylar has a very low absorption coefficient for the IR laser wavelength that is used, with evaluated transmission of the order of 90 % [12]. Using the same experimental condition, in a pure Cu target, 1 µm in thickness, the maximum proton energy was evaluated to be 1.2 MeV. The proton energy in- creases with the Cu deposition thickness, from 10 nm (b) to 50 nm (c) and to 100 nm (d), and assume an en- ergy of 1.1 MeV, 3.2 MeV and 1.5 MeV, respectively, as demonstrated by the TOF measurements of the four spectra. This result is due to two causes: enhance- ment of the plasma electron density responsible for the electric field driving the proton acceleration, and enhancement of the laser absorption in the thin target obtained using the Cu metal. The optimal Cu thick- ness seems to be 50 nm according to the replicability of the measurements under the same experimental conditions. C ions are accelerated to maximum ki- netic energies approximately proportional to six times the maximum proton energy, in agreement with the Coulomb acceleration in the charge space separation generated in the rear side of the thin target. 151 M. Cutroneo, L. Torrisi, A. Mackova, A. Velyhan Acta Polytechnica Figure 3. TPS spectra for irradiation of pure mylar (a) and of mylar covered with a Cu thickness of 10 nm (b), 50 nm (c) and 100 nm (d). Thus, in the case of a 50 nm Cu/mylar target, the carbons are accelerated up to about 20 MeV, due to the six charge states of carbon ions. The corresponding TPS spectra of the targets irradiated in the condi- tions reported for Fig. 2 are presented in Fig. 3. This figure compares the TPS protons and carbon parabo- las achieved by irradiating a pure mylar (a) and the parabolas obtained when we increase the thickness of the Cu film deposited on mylar, from 10 nm (b) to 50 nm (c) and to 100 nm (d). The parabola recog- nition was obtained for comparison with simulation programs based on the real TPS geometry and used value of deflecting magnetic and electric fields used here, as presented in literature [11]. Recognition of the Cu parabolas permits full Cu ionization, up to Cu+29, to be evinced. For the pure mylar foil the parabola luminosity de- creases, as a consequence of the lower plasma electron density and the lower absorbed laser energy in the polymeric film, which absorbs only about 10 % of the laser pulse energy [12]. The parabolas obtained in the other cases shows more energetic ions and may be more luminous. The most energetic ions, less deflected by the magnetic and electric fields, are produced for a Cu thickness of 50 nm deposited on the mylar sub- strate, in agreement with measurements obtained by SiC. Such a thin film produces high laser absorption due to the presence of the metal which absorbs the IR laser radiation and also due to the Cu nanoparticles in which surface plasmon resonant absorption effects are induced by the laser electromagnetic wave [13]. Thus laser absorption enhancement is induced in the target and transferred to the plasma, the Cu thin film in- creases the plasma electron density and consequently the charge separation developed in the rear side of the target and higher ion acceleration is developed. The Cu nanoparticle absorption plays an important role in laser absorption in the thin mylar target, de- pending on the size of the Cu nanoparticles, which is Target Thickness El (J) Ep(H+) Mylar 8 µm 471 0.9 MeV Cu/Mylar 10 nm/8 µm 500 1.0 MeV Cu/Mylar 50 nm/8 µm 495 3.2 MeV Cu/Mylar 100 nm/8 µm 486 1.5 MeV Mylar/Cu 8 µm/100 nm 472 1.1 MeV Cu 1 µm 608 1.2 MeV Table 1. Summary of results of proton acceleration obtained irradiating different thin films. very high for particles with dimensions of the order of hundreds nm absorbing in the range of visible and IR wavelengths. 4. Conclusions Bilayer targets, consisting of milar foil 8 µm in thickness covered with thin Cu PVD depositions, with thicknesses ranging between 10 nm and 100 nm, are suitable for high energy proton acceleration in the forward direction from laser intensity of about 1015 W/cm2 in the TNSA regime. A summary of our results is given in the Table 1, demonstrating that the Cu nanostructures increase the proton acceleration as result of the enhanced laser absorption in the thin film. Mylar covered by Cu was laser irradiated from the Cu face. Irradiating on the converse face, from mylar to Cu, the maximum proton energy decreases with respect to the value obtained when irradiating from the Cu face, as presented in the table. A possible explanation involves the plasma elec- tron density which is higher in the case of Cu/mylar irradiation due to high Cu electron injection in the Mylar plasma. In conclusion three main parameters play an important role in ion acceleration in the for- ward direction from the TNSA regime: (1) the plasma electron density, which can be increased using metals to cover the polymer filmsthat inject the electrons into the polymer plasma; (2) the use of metallic nanos- tructures depsited on the polymer, which significantly increase the laser absorption due to surface plasmon resonance effects at wavelength in the visible and IR regions; (3) the use of an optimal laser focal posi- tion to induce self-focusing effect in thin films. For polymers a distance of −100 µm in front of the target surface is used. This enables the laser light due to the formation of the first ionized vapor to be focused, and enables the self-focusing effect to be made use of. Acknowledgements The authors acknowledge the PALS laser team for its ex- pert support for this experiment and Mr C. Cutroneo and Mrs M. D’Amico for their precious contribution. Access to the PALS laser facility was supported by the Euro- pean Commission under LASERLAB-Europe by project pals001823 and by project P108/12/G108. 152 vol. 55 no. 3/2015 Polymers Containing Cu Nanoparticles References [1] M. von Allmen. Laser-beam interactions with materials. Second printing. Springer Series in Material Science 2, Berlin, 1987. [2] J. Badziak. Laser-driven generation of fast particles. Opto-Electron 15:1–12, 2007. [3] L. Laska, K. Jungwirth, K. Kralikova, al. Charge-energy distribution of ta ions from plasmas produced by i and 3 frequencies of a high-power iodine laser. Rev Sci Instrum 75:1588–1591, 2004. [4] L. Torrisi, D. Margarone, A. Borrielli. Characterization of laser-generated silicon plasma and rdquo. Laser Part Beams 26:379–387, 2008. [5] M. Borghesi, A. J. Mackinnon, L. Barringer, al. Relativistic channeling of a picosecond laser pulse in a near-critical preformed plasma. J Phys Rev Lett 78:879–882, 1997. [6] L. Torrisi, M. Cutroneo, S. Cavallaro, al. Thomson parabola spectrometry as diagnostics of fast ion emission from laser-generated plasma. Proc of SPIE 8779:1–6, 2013. [7] K. Jungwirth, A. Cejnarova, L. Juha, al. The prague asterix laser system pals. Phys Plasmas 8:2495–2501, 2001. [8] L. Laska, J. Krasa, K. a. Masek. Iodine laser production of highly charged ta ions. Czechoslovak Journal Physics 46(11):1099–1100, 1996. [9] L. Torrisi, G. Foti, L. Giuffrida, al. Single crystal silicon carbide detector of emitted ions and soft x rays from power laser-generated plasmas. J Appl Phys 105:123304, 2009. [10] A. Lo Giudice, F. Fizzoti, C. Manfredotti, al. Average energy dissipated by mev hydrogen and helium ions per electron-hole pair generation in 4h-sic. Appl Phys Lett 87:222105, 2005. [11] M. Cutroneo, L. Torrisi, L. Andó, al. Thomson parabola spectrometerfor energetic ions emitted from sub-ns laser generated plasmas. Acta Polytechnica 53(2):138–141, 2013. [12] Dupont. Dupont teijin film. 2014. [13] M. A. Garcia. Surface plasmons in metallic nanoparticles: fundamentals and applications. Journal of Physics D: Applied Physics 44:283001–20, 2011. 153 Acta Polytechnica 55(3):150–153, 2015 1 Introduction 2 Material and Methods 3 Results and Discussion 4 Conclusions Acknowledgements References