Acta Polytechnica doi:10.14311/AP.2015.55.0237 Acta Polytechnica 55(4):237–241, 2015 © Czech Technical University in Prague, 2015 available online at http://ojs.cvut.cz/ojs/index.php/ap ABOUT THE UNIFORMITY AND THE STABILITY OF A VOLUME DISCHARGE IN HELIUM IN NEAR-ATMOSPHERIC PRESSURE V. S. Kurbanismailova, O. A. Omarova, G. B. Ragimkhanova, A. A. Aliverdieva, b, ∗ a Dagestan State University, Gadjieva Str. 43A, 367025, Makhachkala, Russia b DSC Institute for Geothermal Research of the Russian Academy of Sciences, Pr. Shamilya 39A, 367030, Makhachkala, Russia ∗ corresponding author: aliverdi@mail.ru Abstract. We present experimental electric and time-spatial characteristics of a volume discharge and of the transition from a volume burning stage into a channel mode nearing atmospheric pressure. We show that the discharge uniformity rises with the increase of cathode spots density and gas pressure. Keywords: discharge formation; volume discharge; streamer; discharge plasma. 1. Introduction One of the applications of volume discharges in inert gases is gas laser pumping. In this case, in order to in- crease the power characteristics of gas lasers, we need (i) to improve the pumping methods and (ii) to opti- mize the excitation conditions [1,2,3,4,5,6,7]. A prob- lem of pumping optimization consists in the reception of certain electric characteristics of discharge plasma with a constant spatial uniformity during the pump- ing. The discharge instability results in the transition from volume burning into a channel stage (contracted discharge). There can be various physical mechanisms responsible for discharge instabilities. They depend on the gas (or the gas mixture) [8,9,10,11,12]. There- fore the study of volume discharge properties in pure gases has both basic and practical interest. Toward this general aim we have experimentally investigated under a wide range of initial conditions, the plasma characteristics of volume and contracted discharges, as well as the processes of discharge coun- teraction and plasma torch creation in helium at at- mospheric pressure. 2. Experimental installation and research methods The experimental setup and research methods are simi- lar to those described in our previous papers [13,14,15]. The gap under study (about 1 cm in length) irradiates either by spark discharge through the grid anode or by UV source placed in the same gas at a distance of 5–7 cm from the main gap axis. The diameter of the electrodes is 4 cm. We have used electrodes with various shapes (plane and hemispherical, R = 30 cm) made of different materials: aluminium, stainless steel and copper. The pulsed voltage source generates voltage pulses with a variable amplitude of up to 30 kV and a front duration of ∼ 10 ns. The discharge voltage and current are measured with the application of digital oscillo- scopes. Frame photographs of the discharge glow (showing the distribution of radiation intensity both along, and across electrodes) are obtained using a FER-2 streak camera with the UMI-92 image tube. When photographing a discharge in the frame mode, the scanning voltage of the FER-2 is switched off. Frame photographs are synchronized with electrical characteristics of the discharge by simultaneously sup- plying the triggering voltage pulse to the FER-2 and the signal of the discharge current (or voltage) pulse to double-beam storage oscilloscopes. Streak images of the discharge glow (discussed in [15]) are also obtained and synchronized with the discharge current (or volt- age) pulse by applying the signal of the current (or voltage) pulse to the deflecting plates of the UMI-92 image tube, simultaneously with the discharge scan- ning. Time-integrated photographs of the discharge glow with a high spatial resolution are taken using a digital camera. 3. Results and discussion We have investigated a discharge transition from a volume burning into a channel stage in helium with a discharge area S = 12 cm2, a distance between electrodes d = 1 cm, a gas pressure P = 1–5 atm, a discharge voltage U from static discharge up to hundreds of percent of overvoltage. As we can see from Fig. 1 photos 1–4, a homoge- neous volume discharge burns at small external fields (E0 < Ecritical = 6 kV/cm). The growth of uncom- pleted anode channels (which are adhered to cathode spots with high conductivity) starts from a current density of about 40 A/cm2 (see Fig. 1 photos 5–6). An increase in current density up to 60 A/cm2 (see Fig. 1 photos 7–11) leads to further promotion of un- completed anode channels, anode spotting, and also to the appearance of uncompleted cathode channels. When the current density surpasses 100 A/cm2, the anode and cathode channels merge (Fig. 1 phot 12). 237 http://dx.doi.org/10.14311/AP.2015.55.0237 http://ojs.cvut.cz/ojs/index.php/ap V. S. Kurbanismailov, O. A. Omarov, G. B. Ragimkhanov, A. A. Aliverdiev Acta Polytechnica Figure 1. Time-integrated photos of the discharge glow at atmospheric pressure. (a) (b) Figure 2. Typical oscillograms of current and voltage: (a) U0 = 8 kV, P = 1 atm, d = 1 cm; (b) U0 = 9 kV, P = 3 atm, d = 1 cm). Here, t0 is the beginning of the applied voltage growth; t1 is the beginning of the first voltage drop; t3 is the beginning of counteraction of a volume discharge in a spark channel; t3 − t2 is the volume phase duration. The instant of a discharge interval overlapping with a plasma channel (Fig. 1 photo 12) is clearly visible, when the growth of channel conductivity causes a second sharp voltage drop (see Fig. 2). In the coordinated pump mode, a specific heat input of ∼ 0.1 J/cm3 is provided, which is the maximum for helium in a homogeneous burning stage. The duration of discharge uniformity is adjusted by the reduction of the current density or by the increase of gas pressure. At a pressure of 5 atm, the step on a pulse voltage is practically not visible. In this case the volume discharge duration is defined by the time of switching of the discharge current. The voltage pulse on the discharge interval thus smoothly falls down up to arc value. Oscillograms (Fig. 2) and discharge glow pictures, with fixed spatial (Fig. 1) and temporal (see [15,16]) resolutions, show on the one hand the dynamics of discharge development, and on the other hand allow us to define the duration of breakdown stages. 238 vol. 55 no. 4/2015 About the Uniformity and the Stability of a Volume Discharge in Helium Figure 4. Distributions of radiation intensity (in a.u.) both along and across electrodes (d = 1 cm, P = 1 atm): (a) t = 105 ns; (b) t = 130 ns; (c) t = 155 ns; (d) t = 210 ns. Here x is the coordinate along a field, and y is the coordinate across a field. Figure 3. Dependences of the burning voltage of vol- ume discharge on pressure: (1) E/P = 3 kV/cm atm; (2) E/P = 3.5 kV/cm atm. The reduction of the duration of the volume dis- charge burning stage due to the pressure growth, is the result of non-compensated growth of the number of ionization processes relatively to the recombina- tion ones. The increase in gas pressure results in an increase of the voltage at the discharge column. This results in the growth of ionization processes due to the shock ionization that is caused by the strong dependence of the factor α on E0, as well as to the step ionization. The rough uncompensated growth of electron concentration then results in growth of con- ductivity and in the recession of voltage up to the arc value. Afterwards, the discharge moves to a recombi- nation mode and dies. The increase of the overvoltage up to 300 % causes the appearance of a large number of plasma channels having a rather large diameter. The time-differentiation of volume and high-current stages is well visible on oscillograms of the discharge current or of the voltage on the plasma channel. At volume stage of discharge burning the voltage Ub =const., and this constant value depends on pres- sure (see Fig. 3), corresponding to the minimal voltage of the breakdown with the fixed value of Pd, where P is gas pressure and d is interval length. To obtain a sparkless mode we need to obtain a full dispersion of storage element energy (C = 1.5 · 10−8 F) for burning time τb [1]. For volume discharges in He this requirement is reached at U0 = 2Ub, where Ub ≈ 3000 V is the volume discharge burning volt- age at P = 1 atm, d = 1 cm). The analysis of such measurements shows that the spark channel in this case is initiated by instabilities in near-electrode areas [15,18]. These instabilities define the binding of nar- row diffusive channels and cause the transition from a volume discharge mode into a spark mode. Figure 4 shows the distributions of radiation intensities both 239 V. S. Kurbanismailov, O. A. Omarov, G. B. Ragimkhanov, A. A. Aliverdiev Acta Polytechnica along the field and across electrodes. From this figure follows that the counteraction process is defined by near-electrodes phenomena. On the other hand, the basic energy is entered in the discharge in quasi-stationary stages. Then, fot the energy density, it is possibleto write: W = Pτb V = IUτb Sd = jUτb d , (1) where τb is the volume stage duration, j is the current density. The energy, given to the gas before the formation of the spark channel, increases the power, although the burning duration τb exponentially decreases with field growth [16]. Finally, the volume discharge emits a spark in the channel at the critical current density j ≥ jcritical ≈ 40 A/cm2 and the extreme specific inputs ≈ 0.1–0.2 J/cm3 [13]. In a voltage drop stage (when we have a quasi- neutral plasma column with the cross-section area S and electron density ne in the discharge interval) the resistance of this column defined by R = U I = Pd Senek , (2) where µ and νdr = kEP = µE are the mobility and the drift speed of electrons. Accordingly, k = µP = 6.72 · 105 cm2 torr/V sec [1]. For our experiment S = 12 cm2; P = 760 torr; d = 1 cm; ne ≈ 1013–1014 cm3. The resistance ranges from 10 to 100 Ω. 4. Conclusions To sum up, we can observe a clear sequence of events: (1.) the occurrence of cathode spots in an initial stage of discharge; (2.) the development of uncompleted anode channels; (3.) the formation of uncompleted cathode channels; and finally (4.) the merging of counter channels and the growth of their conductivity. In conditions of strong preliminary ionization and with a wide range of initial voltage values the discharge has a volume structure, and the duration decreases with the growth of the initial voltage and gas pressure. In the case of an extreme specific heat input ≈ 0.1 J/cm3 and a critical current density jcritical ≥ 40 A/cm2, the discharge contracts to a spark channel. The burning voltage Ub at various values of E/P tends to reach such value at which Ub/Pd is constant. At the same time the ionization ability of electrons η = α/E0 is maximal and optimal for electron multi- plication. The relation E/P in the volume discharge plasma does not depend on an initial voltage (for P = 1 atm, E/P ≈ 3 · 103 V/cm atm). A volume dis- charge voltage determined basically by gas pressure, has a linear dependence in quite wide ranges. Acknowledgements The work was partially supported by RFBR (12-02-96505, 12-01-96500, 12-01-96501) and it was written within the framework of the State task 2.3142.2011 Ministry of Sci- ence and Education of Russian Federation for 2012–2014. References [1] Korolev Yu.D. and Mesyats G.A. Physics of Pulsed Gas Breakdown. Nauka, Moscow, 1991 (in Russian). [2] Mesyats G.A. and Korolev Yu.D. High-pressure volume discharges in gas lasers. Sov. Phys. Usp., 29, 1986, 57-69. doi:10.1070/pu1986v029n01abeh003083 [3] Woodard B.S., Zimmerman J.W., Benavides G.F., et al. Demonstration of an iodine laser pumped by an air–helium electric discharge. J. Phys. D: Appl. Phys., 43, 2010, 025208. doi:10.1088/0022-3727/43/2/025208 [4] Meek J.M. and J.D. Craggs, Electrical Breakdown of Gases. Quarterly Journal of the Royal Meteorological Society, 80 (344), 1954, 282-283, doi:10.1002/qj.49708034425 [5] Panchenko A.N., Tarasenko V.F., Belokurov A.N., Mendoza P., and Rios I. Planar KrGl excilamp pumped by transverse self-sustained discharge with optical system for radiation concentration. Phys. Scr. 74, 2006, 108-113. doi:10.1088/0031-8949/74/1/013 [6] Feng X., Zhu S. Investigation of excimer ultraviolet sources from dielectric barrier discharge in krypton and halogen mixtures. Phys. Scr. 74, 2006, 322-325. doi:10.1088/0031-8949/74/3/005 [7] Lisenko A.A., Lomaev M.I., Skakun V.S., and Tarasenko V.F. Effective emission of Xe2 and Kr2 bounded by a dielectric barrier. Phys. Scr.. 76 (3), 2007, 211-215. doi:10.1088/0031-8949/76/3/001 [8] Raizer Y.P. Gas Discharge Physics. Berlin, Springer, 1991. doi:10.1007/978-3-642-61247-3 [9] Pancheshnyi S., Nudnova M. and Starikovskii A. Development of a cathode-directed streamer discharge in air at different pressures: experiment and comparison with direct numerical simulation, Phys. Rev. E. 71 (1), 2005, 016407. doi:10.1103/physreve.71.016407 [10] Morrow R. and Lowke J. Streamer propagation in air. J. Phys. D: Appl. Phys. 30, 1997, 614-627. doi:10.1088/0022-3727/30/4/017 [11] Clevis T.T.J., Nijdam S. and Ebert U. Inception and propagation of positive streamers in high-purity nitrogen: effects of the voltage rise rate. J. Phys. D: Appl. Phys., 46, 2013, 045202. doi:10.1088/0022-3727/46/4/045202 [12] Bologa A., Paur H.R., Seifert H., and Woletz K. Influence of gas composition, temperature and pressure on corona discharge characteristics. International Journal on Plasma Environmental Science & Technology. 5, 2011, 110-116. http://www.iesj.org/html/service/ijpest/ vol5_no2_2011/IJPEST_Vol5_No2_02_pp110-116.pdf [13] Kurbanismailov V.S. and Omarov O.A. The behavior of volume discharge contraction in helium at atmospheric pressure. Teplofiz. Vys. Temp. 33, 1995, 346. https://getinfo.de/app/ The-Behavior-of-Volume-Discharge-Contraction-in/ id/BLSE%3AEN029241892 240 http://dx.doi.org/10.1070/pu1986v029n01abeh003083 http://dx.doi.org/10.1088/0022-3727/43/2/025208 http://dx.doi.org/10.1002/qj.49708034425 http://dx.doi.org/10.1088/0031-8949/74/1/013 http://dx.doi.org/10.1088/0031-8949/74/3/005 http://dx.doi.org/10.1088/0031-8949/76/3/001 http://dx.doi.org/10.1007/978-3-642-61247-3 http://dx.doi.org/10.1103/physreve.71.016407 http://dx.doi.org/10.1088/0022-3727/30/4/017 http://dx.doi.org/10.1088/0022-3727/46/4/045202 http://www.iesj.org/html/service/ijpest/vol5_no2_2011/IJPEST_Vol5_No2_02_pp110-116.pdf http://www.iesj.org/html/service/ijpest/vol5_no2_2011/IJPEST_Vol5_No2_02_pp110-116.pdf https://getinfo.de/app/The-Behavior-of-Volume-Discharge-Contraction-in/id/BLSE%3AEN029241892 https://getinfo.de/app/The-Behavior-of-Volume-Discharge-Contraction-in/id/BLSE%3AEN029241892 https://getinfo.de/app/The-Behavior-of-Volume-Discharge-Contraction-in/id/BLSE%3AEN029241892 vol. 55 no. 4/2015 About the Uniformity and the Stability of a Volume Discharge in Helium [14] Bairkhanova M.G., Gadzhiev M.H., Kurbanismailov V.S., Omarov O.A., Ragimkhanov G.B., Kata A.J. The front wave instability of cathode streamer ionization in the Helium of high pressure. Applied Physics. 5, 2009, 62-66. http://applphys.orion-ir.ru/appl-09/09-5/ 09-5-9e.htm [15] Omarov O.A., Kurbanismailov V.S., Arslanbekov M.A., Gadjiev M.Kh., Ragimkhanov G.B., Al-Shatravi A.J.G. Expansion of the cathode spot and generation of shock waves in the plasma of a volume discharge in atmospheric-pressure helium. Plasma Physics Reports, 38 (1), 2012, 22-28. doi:10.1134/s1063780x11120087 [16] Kurbanismailov V.S., Omarov O.A., Ragimhanov G.B., and Aliverdiev A.A., Volume discharge in Helium nearby atmospheric pressure: uniformity and stability // Plasma Physics and Technology. 1 (3), 2014, 112-114. [17] Kurbanismailov V.S., Omarov O.A., Ragimkhanov G.B., Gadzhiev M.Kh., Bairkhanova M.G., and Kattaa A.J. Peculiarities of Formation and Development of Initial Stages of an Impulse Breakdown in Argon. Plasma Physics Reports. 37 (13), 2011, 1166-1172. doi:10.1134/s1063780x11030068 [18] Efendiev A.Z. and Aliverdiev A.A. Multichannel helium discharge in a nonuniform field, Radiophysics and Quantum Electronics. 20 (8), 1977, 850-855. doi:10.1007/bf01038796 241 http://applphys.orion-ir.ru/appl-09/09-5/09-5-9e.htm http://applphys.orion-ir.ru/appl-09/09-5/09-5-9e.htm http://dx.doi.org/10.1134/s1063780x11120087 http://dx.doi.org/10.1134/s1063780x11030068 http://dx.doi.org/10.1007/bf01038796 Acta Polytechnica 55(4):237–241, 2015 1 Introduction 2 Experimental installation and research methods 3 Results and discussion 4 Conclusions Acknowledgements References