Acta Polytechnica doi:10.14311/AP.2018.58.0195 Acta Polytechnica 58(3):195–200, 2018 © Czech Technical University in Prague, 2018 available online at http://ojs.cvut.cz/ojs/index.php/ap CHARACTERIZATION OF RECYCLED LINEAR DENSITY POLYETHYLENE/IMPERATA CYLINDRICA PARTICULATE COMPOSITES Olusola Femi Olusunmadea, ∗, Sunday Zechariahb, Taofeek Ayotunde Yusufa a Department of Mechanical Engineering, University of Agriculture, Makurdi, PMB 2373, Makurdi, Nigeria b Department of Mechanical Engineering, Federal Polytechnic, Mubi, Nigeria ∗ corresponding author: olusunmadeolusola@yahoo.com Abstract. Water-sachets made from low density polyethylene (LDPE) form a bulk of plastic wastes which creates environmental challenges, while certain species of plants like Imperata cylindrica constitute large portion of weeds on farm lands. As a technological approach to the reduction and utilization of these materials, composites of Imperata cylindrica (IC) particulate and synthetic polymer (from recycled waste water-sachets) were produced and evaluated for several mechanical and physical properties. The production of the composites and testing were done using the standard methods available in the literature. The results showed an increase in tensile modulus, hardness, impact strength, and water absorption of the composite in comparison with unreinforced polymer, as the IC particulate loading increased from 5 wt% to 30 wt%. However, there was a decrease in tensile strength, percentage elongation at break and density of the composite as the particulate loading increased from 5 wt% to 30 wt%. The combination of the recycled waste water-sachets and IC particulate is really promising for composites development. This creates opportunities to reduce LDPE wastes and add economic importance to an otherwise agricultural menace. It will mean creating an economic value from “wastes”. Keywords: mechanical properties; physical properties; Imperata Cylindrica (IC); particulate; waste water-sachets; composites and recycled linear low density polyethylene (RLDPE). 1. Introduction The development of composite materials, particularly natural fibre composites, has become increasingly pop- ular. The volume and number of applications of com- posite materials have grown steadily, reaching to and conquering new markets. According to a market re- port published by Lucintel [1], the future of natural fibre composites market looks attractive with oppor- tunities in the automotive as well as building and construction industries. Modern composite materials constitute a significant proportion of the engineered materials market ranging from everyday products to sophisticated applications. The efforts to produce eco- nomically attractive composite components have re- sulted in several innovative manufacturing techniques currently being used in the composites industry [2]. These composite materials are sometimes produced using waste resources. The fact that natural resources are ever depleting calls for more responsible and ef- ficient use of the available scarce resources. Besides, creating products from “waste” will really add value and help with environmental challenges posed by the enormous waste being generated. In many countries in Africa, potable water is being packed with sachets made from linear density polyethylene (LDPE). This has really become a big business in many cities. As a result of increasing demand for the packed water, there has been a rise in the amount of waste water- sachets generated. These empty sachets often end up thrown away on the streets creating large amount of non-biodegradable waste. Responsible utilization of these wastes will really be an advantage. The water-sachets clog mini-water ways, thereby creating a perfect breeding habitat for mosquitoes that are responsible for spreading malaria parasite, which is a major cause of illness on the African continent. Even- tually, the water-sachets find their way to larger bodies of water such as oceans and seas and pose a serious threat to aquatic life, as these wastes can be around for many years because of their non-biodegradable nature. However, if the water-sachets are burnt, the emissions from the burning process severely pollutes the air and also contribute to the greenhouse effect, which is responsible for the global warming that the earth currently experiences as a result of the depleting ozone layer. There is, therefore, a need for a respon- sible handling of these wastes. One of such efforts targeted at utilizing the waste water-sachets is by incorporating natural fibres into them to produce a usable composite materials. Natural fibres could serve as viable and abundant alternatives to the expensive and non-renewable synthetic fibres as reinforcement in thermoplastic composites. These types of fibres present many advantages compared to synthetic fibres, such as low tool wear, low density, cheaper cost, avail- ability and biodegradability [3, 4]. One of such natural 195 http://dx.doi.org/10.14311/AP.2018.58.0195 http://ojs.cvut.cz/ojs/index.php/ap O. F. Olusunmade, S. Zechariah, T. A. Yusuf Acta Polytechnica Supplementary Materials Figure 1: Ground IC Figure 2: Waste Water-Sachets Figure 1. Ground IC. fibres is Imperata cylindrica. It is an aggressive and difficult weed to control due to its short growth cycle. It is abundant, yet unsuitable for grazing animals and lacks a good commercial value [5]. When fully mature, its overall nutrient decline and its sharp pointed seeds and tangled awns may injure animals and humans [6]. They also act as a host for pathogens that affect the yield of some food crops [7]. However, Imperata cylin- drica possesses good stiffness properties, which, if incorporated in a matrix, can enhance the composite rigidity. Hence, Imperata cylindrica is proposed as a fibre reinforcement for recycled water-sachets to pro- duce a thermoplastic composite, thereby increasing its economic importance and reduce the environmen- tal challenges posed by improper handling of waste water-sachets. This study, therefore, examined some mechanical and physical properties of recycled water- sachets/Imperata cylindrica particulate composite to determine its viability for engineering applications. 2. Materials and method The part of the Imperata cylindrica (IC) that was used for this study is the stem and they were obtained from Pilla village in Makurdi area of Benue State. The waste water-sachets were gathered from the campus of the University of Agriculture Makurdi, Benue State. 2.1. Polymer and fibre processing The Imperata cylindrica stems were harvested and sun- dried for two weeks. Subsequently, the finer strands of the stems were handpicked and ground (see Figure 1). The grounded particles were then filtered through a sieve of a pore size of 300 microns. The waste water- sachets (see Figure 2) were thoroughly washed, dried and pulverized at Goshen Plastics Industry, Makurdi (see Figure 3). These pulverized waste water-sachets will be referred to as recycled low density polyethylene (RLDPE) henceforth. 2.2. Composite preparation The IC particulate and the RLDPE were weighed to get the required weight using an electronic weigh- ing balance (Ohaus Adventurer Pro Analytical bal- Supplementary Materials Figure 1: Ground IC Figure 2: Waste Water-Sachets Figure 2. Waste Water-Sachets. Figure 3: Pulverized Water-Sachets Figure 4: Compression of mold and content Figure 3. Pulverized Water-Sachets. ance). The IC particulate and the recycled polymer were mixed such that the particulate weight ratio in the matrix varied from 5 wt% to 30 wt% in steps of 5 wt%. The mould was preheated at 100 °C. Half of the RLDPE was added to the mould because the cav- ity of the mould could not accommodate the whole mass of the RLDPE in an un-melted state. After one minute, the IC particulate was added to the mould and after that, the other half of the RLDPE was also added. The combined IC particulate and RLDPE were then heated in the Aluminium mould at a tem- perature of 150 °C for 15 minutes, during which the RLDPE showed a reasonable fluidity and the blend was thoroughly mixed to ensure homogeneity. The heating continued for another 5 minutes after which the mould was removed from the heat source and com- pressed using a 5tonnes hydraulic jack (see Figure 4). It was then allowed to cool at a room temperature un- til the composite took the shape of the mould cavity, after which the composite sheet (295 × 210 × 5 mm) was removed from the mould. Heating was carried out using a QASA (QSG-505G) gas cooker. 2.3. Composite characterization The IC particulate-reinforced plastic sheet was re- trieved from the mould and cut into test specimens. Characterization of the composites was achieved by mechanical testing. Some physical properties of the materials were also examined. 196 vol. 58 no. 3/2018 Characterization of Recycled Particulate Composites Figure 3: Pulverized Water-Sachets Figure 4: Compression of mold and content Figure 4. Compression of the mould and content. 2.3.1. Mechanical properties Tensile test was carried out using the Instron 3369 (Universal Testing Machine) according to ASTM D 638, to determine the tensile strength, tensile modu- lus, and elongation at break of the materials. The test specimen had a dumb-bell shape with a gauge length of 30 mm, grip width of 15 mm and thickness of 5 mm. Specimens were placed in the grips of the universal tester and pulled at a crosshead speed of 5 mm/min until failure. The hardness of the materials was mea- sured using a Computerized Micro-Vickers Hardness Tester (MV-1 PC) with a load of 300g according to ASTM E 384, which is a standard test method for Vickers hardness testing of materials. The Vickers indenter produces a geometrically similar indentation at all test forces. The dimension of the hardness spec- imens is 40 × 40 × 5 mm. The Charpy impact test was carried out to determine the impact strength of the composites according to ASTM D 6110, which is used to determine the resistance of plastics to a breakage by flexural shock produced by a pendulum type ham- mer. The dimension of the impact test specimens was 100 × 10 × 5 mm. Three specimens from each of the materials were used for each of the tests. 2.3.2. Physical properties Water absorption test according to ASTM D-570 was also carried out to determine the water absorption characteristic of the composite. Three samples from each of the materials, with dimensions 42 × 12 × 5 mm, were cut, cleaned and weighed before immersion in distilled water at a room temperature. The speci- mens were removed from the water after 24 hours and the surfaces wiped off and weighed. The differ- ence between the weight before and after immersion was noted. The water absorption was then calculated using A = M2 − M1 M1 · 100 %, (1) where M1 is the initial mass in grams and M2 is the final mass in grams. Figure 5: Tensile strength at varying IC particulate loading 0 2 4 6 8 10 12 0 5 10 15 20 25 30 T e n si le S tr e n g th ( M P a ) IC Particulate Loading (wt%) Figure 5. Tensile strength at varying IC particulate loading. The density of the composite was also determined by comparing the mass of a given specimen with its volume: density (%) = mass (m) volume (v) . (2) The dimensions of the specimens used to determine the density was 50 × 50 × 5 mm. 3. Results and discussion 3.1. Mechanical properties 3.1.1. Tensile strength Figure 5 illustrates the average tensile strength of the composite produced at different IC particulate load- ings as compared to the RLDPE. It showed that the RLDPE has an average tensile strength of 10.86MPa. It was observed that there was a decrease of 16.48 % to 34.07 % in the average tensile strength of the com- posite as the IC particulate loading increased from 5 wt% to 30 wt% compared to the RLDPE. Though, there was an increment of 6.39 % in the average ten- sile strength of the composite for particulate loading from 5 wt% to 15 wt%. The maximum average tensile strength of the composite is nevertheless still lower compared to that of the RLDPE. The decrease is due to the poor interfacial adhesion between the hy- drophobic RLDPE and hydrophilic IC particulate. The Scanning Electron Microscope micrographs (see Figures 6 and 7) showed that while the IC particulates were fairly evenly distributed within the matrix, the agglomeration of the particulate observed, however, indicates a weak interfacial bonding. Poor interfacial adhesion acts as a stress concentration point upon an application of external forces leading to a premature failure due to a poor stress transfer from matrix to the fibre particulate. Higher tensile strength demon- strated by the neat RLDPE is due to the flexibility and plasticity of the RLDPE [3]. 3.1.2. Tensile modulus Figure 8 illustrates the average tensile modulus of the composite produced at different particulate load- 197 O. F. Olusunmade, S. Zechariah, T. A. Yusuf Acta Polytechnica Figure 6: SEM Micrograph at 20 wt% IC Particulate Loading Figure 7: SEM Micrographs at 30 wt% IC Particulate Loading Particles Polymer Matrix Agglomeration of particulates Figure 6. SEM Micrograph at 20 wt% IC Particulate Loading. Figure 6: SEM Micrograph at 20 wt% IC Particulate Loading Figure 7: SEM Micrographs at 30 wt% IC Particulate Loading Particles Polymer Matrix Agglomeration of particulates Figure 7. SEM Micrographs at 30 wt% IC Particulate Loading. Figure 8: Tensile Modulus at varying IC particulate loading 0 50 100 150 200 250 0 5 10 15 20 25 30 T e n si le M o d u lu s (M P a ) IC Particulate Loading (wt%) Figure 8. Tensile Modulus at varying IC particulate loading. ings as compared to the RLDPE. It showed that the RLDPE has an average tensile modulus of 116.44MPa. It was observed that as the particulate loading in- creased from 5 wt% to 30 wt%, there was an increase of 8.78 % to 82.53 % in the average tensile modulus of the composites when compared to the RLDPE. As the IC particulate loading increased, the elasticity of RLDPE has been suppressed by the presence of the derived cellulose. The increment in the modulus is attributed to the decreased deformability of the interface between the IC particulate and the matrix material, which caused a reduced strain as the par- ticulate loading increased, due to the rigidity of the material [3]. Then et al. [8] suggested that the en- hancement in the tensile modulus is probably due to the fibres itself, which have a higher stiffness than those of the polymer. 3.1.3. Percentage elongation at break Figure 9 illustrates the average percentage elongation at break of the composite produced at different cellu- lose loadings as compared to the RLDPE. It showed that the RLDPE has a percentage elongation at break Figure 9: Elongation at break at varying IC particulate loading 0 10 20 30 40 50 60 0 5 10 15 20 25 30 E lo n g a ti o n a t B r e a k ( % ) IC Particulate Loading (wt%) Figure 9. Elongation at break at varying IC particu- late loading. of 54.93 %. It was observed that there was a decrease of 64.73 % to 73.84 % in the average percentage elon- gation at break of the composite as the IC particulate loading increased from 5 wt% to 30 wt% compared to the RLDPE. However, there was an increment of 57.31 % in the average percentage elongation at break of the composite for particulate loading from 5 wt% to 15 wt%. The maximum average percentage elon- gation at break of the composite is nonetheless still lower compared to that of the RLDPE. The incre- ment noticed between 5 wt% and 15 wt% particulate loadings may be attributed to a better dispersion of the particles within the matrix. There was less ag- glomeration of the particles and so a slightly more strain at this range of particulate loading. However, as the IC particulate loading increased, the elastic- ity of the composite is suppressed by the presence of the increased derived cellulose. The reduction is attributed to the decreased deformability of a rigid interface between the IC particulate and the matrix material [3]. Liu et al. [9] reported that the decrease in elongation at break is due to the destruction of the structural integrity of the polymer by the fibres and the rigid structure of the fibres. 198 vol. 58 no. 3/2018 Characterization of Recycled Particulate Composites IC Particulate Impact Hardness Loading (wt%) Strength (HV) (J) 0 5.03 52.63 5 2.68 50.57 10 2.88 64.73 15 2.98 70.63 20 3.45 91.53 25 3.8 103.77 30 4.4 111.33 Table 1. Impact strength and hardness property in relation to IC particulate loading. 3.1.4. Impact strength Table 1 illustrates the average impact strength of the composite produced at different particulate loadings as compared to the RLDPE. It showed that the RLDPE has an average impact strength of 5.03 J. Higher im- pact strength demonstrated by the neat RLDPE is due to the flexibility, plasticity, and less brittleness of the RLDPE, which allows it to absorb and distribute the impact energy efficiently [3]. There was an increase of 7.46 % to 64.18 % in the average impact strength of the composite as the IC particulate loading increased from 5 wt% to 30 wt%. Nevertheless, the maximum average impact strength of the composite at 30 wt% particulate loading was still 12.52 % lower when com- pared to that of the RLDPE. Considering the steady increment that was observed, up to 30 wt% loading of the IC particulate, it is possible that if the particulate loading increases beyond 30 wt%, the impact strength of the composite may eventually reach or even exceed that of the RLDPE at some point. The increment in the average impact strength may be attributed to the rigid interface between the IC particulate and the matrix material as the particulate loading increased. 3.1.5. Hardness property Table 1 illustrates the average hardness values of the composite produced at different IC particulate load- ings as compared to the RLDPE. It showed that the RLDPE has an average hardness value of 52.63. It was observed that as the particulate loading increased from 5 wt% to 30 wt%, there was an increase of 22.99 % to 111.53 % in the average hardness values of the composites when compared to the RLDPE. The in- crease in the hardness property observed with the RLDPE/IC particulate composite is a result of the hardness property of the IC particulate itself, which has been transmitted to the composite. The reduction in the hardness value at 5 wt% particulate loading may be as a result of a void in the composite [10]. 3.2. Physical properties 3.2.1. Water absorption Table 2 illustrates the average percentage water ab- sorption of the composite produced at different IC IC Particulate Water Mass Density Loading (wt%) Absorp- (g) (g/cm3) tion (%) 0 4.64 10.69 0.855 5 6.81 10.66 0.853 10 7.11 10.34 0.827 15 7.19 10.01 0.801 20 7.86 9.88 0.791 25 13.66 9.86 0.789 30 15.47 9.77 0.782 Table 2. Water absorption and density in relation to IC particulate loading. particulate loadings as compared to the RLDPE. It showed that the RLDPE has a percentage water ab- sorption of 4.64 %. It was observed that as the IC par- ticulate loading was increased from 5 wt% to 30 wt%, there was an increase of 46.77 % to 233.41 % in the average percentage water absorption of the composites when compared to the RLDPE. This result is accord- ing to expectations, as composites with natural fibre reinforcement exhibit higher water absorption due to the inherent hydrophilic nature of the fillers [11, 12]. 3.2.2. Density Table 2 illustrates the average density of the composite produced at different IC particulate loadings when compared to RLDPE. It showed that the RLDPE has a density of 0.855 g/cm3. It was observed that as the IC particulate loading was increased from 5 wt% to 30 wt%, there was a decrease of 0.23 % to 8.53 % in the average density of the composites when compared to the RLDPE. The decrease in the density observed with the RLDPE/IC particulate composite is as a result of the low density of the IC particulate itself, which has been transmitted to the composite. When a larger fraction of the RLDPE, which is of a higher density, is replaced by lighter particulates, the overall density of the subsequent composite is reduced, which is one advantage that natural fibre composites have over synthetic fibre composites [3] and other engineering materials. 4. Conclusion In this study, RLDPE/IC particulate composites have been produced through a form of hand lay-up tech- niques and the mechanical and physical properties at 5 wt% to 30 wt% particulate loadings have been exam- ined. The results from the tests carried out showed that the tensile modulus, hardness, impact strength and water absorption of the composite increased as the IC particulate loading increased from 5 wt% to 30 wt% respectively. Although, an increasing trend was observed for the impact strength as particulate loading increased up to 30 wt%, the value was still lower compared to that of the RLDPE. By increasing the IC particulate loading beyond 30 wt%, the impact 199 O. F. Olusunmade, S. Zechariah, T. A. Yusuf Acta Polytechnica strength of the composite may eventually reach or even exceed that of the RLDPE at some point. How- ever, tensile strength, percentage elongation at break and density of the composite decreased as particulate loading increased 5 wt% to 30 wt% respectively. Al- though an increase in tensile strength and elongation was observed up to 15 wt% loading of the particulate, the maximum tensile strength and elongation of the composite at that loading was still lower than that of the RLDPE. The results obtained from the tests conducted showed that the composite can actually be adapted in some engineering applications particularly because of the positive indications observed regard- ing tensile modulus, hardness, impact strength and density. The combination of the recycled waste water- sachets and the IC particulate is really promising for a composite development. This creates opportunities to reduce LDPE wastes and add economic importance to an otherwise agricultural menace. It will mean creating an economic value from “wastes”. References [1] LUCINTEL: “Global Natural Fiber Composite Market 2015-2020: Trends, Forecast, and Opportunity Analysis,” Market Research Reports, 2015. [2] CELLUWOOD: “Technologies and Products of Natural Fibre Composites,” CIP-EIP-Eco-Innovation- 2008: ID: ECO/10/277331, 2008. [3] Olusunmade, O. F, Adetan D. A and Ogunnigbo C. O: “A Study on the Mechanical Properties of Oil Palm Mesocarp Fibre Reinforced Thermoplastic (OPMFRT)”, Journal of Composites, vol. 2016, Article ID 3137243, 7 pages, 2016. doi:10.1155/2016/3137243 [4] Ogunsile, B. O and Oladeji, T. G: “Utilization of banana stalk fiber as reinforcement in low density polyethylene composite,” RevistaMateria, artigo11757, 21(4), pp.953-963, 2016. doi:10.1590/s1517-707620160004.0088 [5] Angzzas, S. M. K, Aripin, A. M, Ishak, N, Hairom, N. H. H, Fauzi, N. A, Razali, N. F and Zainulabidin, M. H: “Potential of Cogon Grass (Imperata cylindrica) as an alternative fibre in paper-based Industry,” ARPN Journal of Engineering and Applied Sciences, vol. 11, No. 4, 2016. [6] Soromessa, T: “Heteropogon contortus (L.) Beauv. Ex Roem. & Schult.,” PROTA (Plant Resources of Tropical Africa), Wageningen, Netherlands, 2011. [7] Cook, B. G, Pengelly, B. C, Brown, S. D, Donnelly, J. L, Eagles, D. A, Franco, M. A, Hanson, J, Mullen, B. F, Partridge, I. J, Peters, M and Schultze-Kraft, R: “Tropical Forages: an interactive selection tool,” CSIRO, DPI&F (Qld), CIAT and ILRI, Brisbane, Australia, 2005. [8] Then, Y. Y, Ibrahim, N. A, Zainuddin, N, Ariffin, H and Wan Yunus, W. M. Z: “Oil palm mesocarp fiber as new lignocellulosic material for fabrication of polymer/fiber biocomposites,” International Journal of Polymer Science, vol. 2013, Article ID797452, 7 pages, 2013. doi:10.1155/2013/797452 [9] Liu, L, Yu, J, Cheng, L and Qu, W: “Mechanical properties of poly (butylene succinate) (PBS) biocomposites reinforced with surface modified jute fibre,” Composites Part A: Applied Science and Manufacturing, vol. 40, no. 5, pp. 669–674, 2009. doi:10.1016/j.compositesa.2009.03.002 [10] Kling, V, Rana, S and Fangueiro, R: “Fibre reinforced thermoplastic composite rods,” Materials Science Forum, vol. 730-732, pp. 331–336, 2013. doi:10.4028/www.scientific.net/MSF.730-732.331 [11] Naghmouchi, I, Mutje, P and Boufi, S: “Olive Stones Flour as Reinforcement in Polypropylene Composites: A Step Forward in the Valorization of the Solid Waste from the Olive Oil Industry,” Industrial Crops and Products, 72, 183-191, 2015. [12] Deo, C and Acharya, S. K: “Effect of Moisture Absorption on Mechanical Properties of Chopped Natural Fiber Reinforced Epoxy Composite,” Journal of Reinforced Plastics and Composites, vol. 1 pp. 5-15, 2010. doi:10.1177/0731684409353352 200 http://dx.doi.org/10.1155/2016/3137243 http://dx.doi.org/10.1590/s1517-707620160004.0088 http://dx.doi.org/10.1155/2013/797452 http://dx.doi.org/10.1016/j.compositesa.2009.03.002 http://dx.doi.org/10.4028/www.scientific.net/MSF.730-732.331 http://dx.doi.org/10.1177/0731684409353352 Acta Polytechnica 58(3):195–200, 2018 1 Introduction 2 Materials and method 2.1 Polymer and fibre processing 2.2 Composite preparation 2.3 Composite characterization 2.3.1 Mechanical properties 2.3.2 Physical properties 3 Results and discussion 3.1 Mechanical properties 3.1.1 Tensile strength 3.1.2 Tensile modulus 3.1.3 Percentage elongation at break 3.1.4 Impact strength 3.1.5 Hardness property 3.2 Physical properties 3.2.1 Water absorption 3.2.2 Density 4 Conclusion References