AP05_3.vp 1 Introduction Electrorheological (ER) fluids are liquids with flow proper- ties that can be changed by stimulation by an electric field. In particular, changes in dynamic viscosity under an electric field have found many applications in various devices such as clutches, brakes, active engine mounts and shock absorbers [1, 2]. The rheological properties of the oil dispersions of stimulus responsive particles have been well documented. The key principle of an ER fluid is the dispersion of electro- -conducting particles in a non-conducting liquid medium. We considered that it woud be interesting to investigate the rheological properties of an ionic liquid. In this work, we study the rheology of a new ionic liquid in electric and mag- netic fields. To the best, of our knowledge, no reports have appeared in the literature dealing with the rheology of ionic liquids. Ionic liquids are salts which are fluids at around room tem- perature. In recent years they have attrached increasing interest. Only in 2001-2002 more than five hundred papers were published. Ionic liquids show unusual physical proper- ties such as high ionic conductivity and powerful solution efficiency for various organic and inorganic substrates. Two types of ionic liquids, imidazolinium salts [3, 4, 5] and tri- alkylammonium salts [6] have been studied extensively by chemists. More recently a new type of ionic liquid, 2-hydroxyethyl- ammonium formate was discovered at the chemistry depart- ment of our university. According to their report [7], it is obtained simply by mixing ethanolamine and formic acid, both of which are commercially available. The freezing tem- perature of this salt is -82 oC, which is the lowest freezing temperature among ionic liquids. This work deals with measurements of the vibration damping effect of the ionic liquid by the logarithmic degre- ment approach under magnetic and electric fields. The variation of the damping coefficient is derived and the results are discussed. Our preliminary experiments show that the new ionic liquid is not stimulated by magnetic fields. How- ever, a relatively high vibration damping effect was detected even under low electricfields, compared with the effects dis- cussed in previous reports. 2 Mechanism of the electro-rheological effect The electrorheological effect refers to the sudden and reversible change in the flow characteristics by means of an electric field. An abtract change in the molecular orientation of the structure from an initially random distribution to a more ordered structure takes place. Furusho classified ER fluids into two-phase (particle-type) and one-phase (homoge- neous-type) systems in terms of their characteristics [8]. Conventional ER fluids, for example suspensions of polarizable solid particles and insulation oil, demonstrate an orientational change in response to an external electric field because of the induced aggregation of the particles. The main disadvantage of two-phase ER fluids is that their characteris- tics change greatly with the shape and dimensions of the par- ticles [9]. Homogeneous-type ER fluids have been developed by using a solution of low-molecule liquid crystals or macro- molecular liquid crystals [10, 11]. Up to now, the ER effects of electron conducting dispersed particles have been studied. Here we present the rheological effect of an ionic liquid in which electrical charges are created by ion migration rather than by electron movements. The ER effect is strongly dependent on polarization rate, permittivity, the dielectric loss factor and conductivity [12]. It is important to note that the structure of the carrier fluid may break down under high electrical fields, when highly conduct- ing substrates are used. Because of this fact, it is not possible to obtain high damping forces. In this case, the dampings received are substantially lower than those produced by mag- netorheological fluids. Zhao et al. demonstrated that the ER effect produced by conducting and dielectric systems are completely different in nature [13]. For instance, network sys- tems are formed rather than linearly aligned chain systems. In fact, the conductivity effect dominates in low frequency AC fields, and permittivity dominates at high frequencies. In other words low frequency AC fields must be applied to con- ductive ER fluids in order to achieve a better ER effect. In this study, we have intestigated the rheological properties of an ionic liquid under DC electric fields. 68 © Czech Technical University Publishing House http://ctn.cvut.cz/ap/ Acta Polytechnica Vol. 45 No. 3/2005 Czech Technical University in Prague Vibration Damping of a New Ionic Liquid under Electric Field Effect M. M. A. Bicak, H. T. Belek, A. Göksenli Ionic liquids are recently-developed smart materials that are not well known by mechanical engineers. They are of great interest due to their non-volatility, viscosity and extremely high electrical conductivity. Up to now, no reports have appeared on their rheological properties under magnetic or electrical fields. In this work, we study the electro-rheological behaviour of a newly presented ionic liquid (2-hydroxyethylammonium formate). Our experiments show that the ionic liquid is not sensitive to magnetic fields. Nevertheless, resonably high damping ratios (42.8%) have been attained under relatively low electric fields (0.6 kVcm�1). Keywords: damping characteristics, ionic liquid, electrorheological fluid. 2 Physical properties of the ionic liquid Recently a new ionic liquid (2-hydroxyethylammo- nium formate), with an extremely low melting temperature (�82 �C), has been reported [7]. This ionic liquid shows reasonably high room temperature ionic conductivity (3.3 mS cm–1) and heat stability up to 150 �C. Other physical properties are given in Table 1. The room temperature conductivity of the ionic liquid is 3.3 mScm-1, which is in the order of metallic conductivities. The ionic conductivity increases exponentially with tempera- ture, and reaches 40 mS cm�1 at 92 °C (Fig. 1). This effect can be attributed to fast ion mobilities at elevated temperatures. The AC conductivity – frequency plot of the ionic liquid (Fig. 2) shows a sharp increase in the (0.1–10) Hz range. A plateau appears between 10 Hz–10 MHz, in which the con- ductivity is around 68 mS cm�1 at room temperature. The viscosity of the ionic liquid decreases with tempe- rature. For instance, 105 cP of room-temperature viscosity reduces to 15 cP at 70 °C. Processing of the temperature dependent viscosity data shows an Arhenius type of relation- ship from which the following correlation is obtained: log . . � � � �5 265 1919 5 T , where � denotes viscosity in terms of cP, and T is tempera- ture (K). 3 Experimental We designed a home-made experimental setup shown in Fig. 3, for damping measurements under an electric field effect. The same setup can also be used under a magnetic field by replacing the electric field with a magnetic coil. The measurements were carried out under (0–0.6) kV cm�1 of a DC electric field. For this purpose the damper reservoir was filled with about 25 ml ionic liquid. The electric field was created by two parallel plates using a control- lable power supply. Meanwhile, the shaker was stimulated by amplified signals. The oscillations generated by the shaker © Czech Technical University Publishing House http://ctn.cvut.cz/ap/ 69 Czech Technical University in Prague Acta Polytechnica Vol. 45 No. 3/2005 Appearance Viscous clear liquid Density 1.204 g cm�3 Refractive index nD � 1.4772 (at 25 °C) Viscosity � � 105 cP (at 25 °C) Conductivity � � 3.3 mS cm�1 (at 25 °C) Decomposition Temperature Approx. 150 °C (by TGA�) Vapor pressure 2.2×10�2 Torr (air saturation method) Melting point Mp (freezing point): � 82°C (*adapted from ref. [7], �Thermo gravimetric Analysis) Table 1: Some physical characteristics of the ionic liquid* C o n d u c ti v it y m S m m -1 Temperature (°C) Fig. 1: Effect of temperature on conductivity Log � A C C o n d u c ti v it y (m S m m -1 ) Fig. 2: AC conductivity – frequency plot were collected and the output responses were collected by a data collector (Bruel & Kjaer). The displacements-time plots are illustrated in Fig. 4., and the logarithmic degrement of the oscillations was calculated by tracing the maxima of the dis- placement signals using the following formula � � � 1 1r A A i i ln , � � � � � 1 1 2 2( ) , where Ai is the first significant amplitude, and Ai�r is ampli- tude after r cycles. The damping forces were recorded simultaneously by means of the force transducers. These experiments were carried out under various electric fields. The data collected is pictured as a function of the electric field, as shown in Fig. 5. 3.1 Measurements under a magnetic field The experiments described above were repeated under constant and sinusoidal magnetic fields supplied from an electromagnetic coil with an inner diameter of 10 cm. Varia- 70 © Czech Technical University Publishing House http://ctn.cvut.cz/ap/ Acta Polytechnica Vol. 45 No. 3/2005 Czech Technical University in Prague m Force Transducer Force Transducer Displacement Transducer Power Supply ER Damper Spring Shaker Data Collector Signal Generator Amplifier Amplifier Fig. 3: Schematic diagram of the testing unit Time (sec.) Displacement (mm) Ai+r Ai 3 - 2 - 1 - Fig. 4: Impulse response of the oscillator Fig. 5: Damping force – time relationship under an electrical field tion of the magnetic field (0–1) Tesla did not give any signifi- cant change in response relative to blank experiments. 4 Results and discussion Although we are not able to apply high electric fields, we have observed reasonable rises in damping ratios as high as 42.8 % in moderate electrical fields up to 0.6 kV cm�1 (Fig. 6). This seems to be due to the quick orientation of the dipoles of the ionic liquids under an electric field. This result is espe- cially significant because such high damping can only be achieved under high electric fields (i.e. 40 kV cm�1), as de- scribed many times in the literature [13]. Since the viscosity of the liquid is inversely proportional to the temperature, high damping performances are expected at lower temperatures. However, the conductivity of the ionic liquid increases with temperature. In other words, the effects of viscosity and conductivity, in our case, are contraversal in the damping ef- fect. Nevertheless, the high solubility of of the liquid compen- sates the disadvantage of the temperatures. For instance, the addition of ammonium chloride (NH4Cl ) increases both the conductivity and the viscosity at the same time. It is important to note that there is a great difference be- tween the present system and the reported data obtained from electroconducting particle dispersions. In the present case, electric conduction is provided by ion migration rather than by electron conduction. In our case, 3.3 mS cm�1 of conductivity at room tempera- ture is comparable with the conductivities of conducting met- als. In other words, the conductivity of the ionic liquid is about 106 times that of particle dispersions reported so far. Better damping effects can be attained by dissolving dis- sociable salts in the ionic liquid at low temperatures. The advantage of the liquid presented here over reported systems is that it can be stimulated by low electric field strengths. The non-volatility of the liquid is another advantage. We have also studied the damping response under a mag- netic field in the (0–1) T range supplied by a magnetic coil. However, no significant response was detected, as expected. 5 Conclusion Ionic liquids are ion conducting viscous liquids which provide reasonable dampings under relatively low electrical fields. The new ionic liquid without any added ingredient does not show any magnetorheological effect. However, due to its powerful solvating effect, the homogeneous or semi- -homogeneous magnetic particle dispersions are of interest. Further studies are under consideration. 6 Acknowledgments We are grateful to Prof. N. Bicak for his valuable help in donating the ionic liquid. References [1] Carlson, J. D., Catanzarite, D. M., St. Clair, K. A.: Electrorheological Fluids, Magnetorheological Suspensions and Associated Technology (ed. W. A. Bullough). Singa- pore: World Scientific, 1996, p. 20. [2] Wu, X. M., Wong, J. Y., Sturk, M., Russell, D. L.: Electro- rheological Fluids: Mechanisms, Properties, Technology and Applications (ed. R. Tao and G. D. Roy). Singapore: World Scientific, 1994, p. 538. [3] Watanabe, M., Yamada, S. I., Ogata, N.: Electrochim. Acta, Vol. 40 (1995), p. 2285–2288. [4] Fuller, J., Breda, A. C., Carlin, R. T.: J. Electrochem. Soc. Vol. 144 (1997), No. 4, L67–L70. [5] Noda, A., Watanabe, M.: Electrochim. Acta, 45 (2000), p. 1265–1270. [6] Forsyth, M., Sun, J., MacFarlane, D. R.: Electrochim. Acta, Vol. 45 (2000), p. 1249–1254. [7] Bicak, N.: “A New Ionic Liquid: 2-Hydroxy Ethyl Am- monium Formate.” J. Molecular Liquids, (in Press) [8] Furusho, J.: “Control of Mechatronics Systems Using Electrorheological Fluids.” Journal of the Society of Instru- ment and Control Engineers, Vol. 34 (1995), p. 687–691. © Czech Technical University Publishing House http://ctn.cvut.cz/ap/ 71 Czech Technical University in Prague Acta Polytechnica Vol. 45 No. 3/2005 Fig. 6: Effect of an electrical field on damping coefficients [9] Johson, A. R., Makin, J., Bollough, W. A.: Advances in Electrorhological Fluids (ed. M. A. Kohudic). Technomic Publ., 1994. [10] Inoue, A., Maniwa, S.: “Electrorheological Effect of Liq- uid Crystalline Polymers.” Journal of Application Polymer Science, Vol. 55 (1995), p. 113–118. [11] Inoue, A.: “Trends of Homogeneous ER Fluid Develop- ment.” Journal of the Society of Instrument and Control Engi- neers, Vol. 34 (1995), p. 698–701. [12] Akhavan, J., Slack, K., Wise, V., Block, H.: “Coating of Polyaniline with an Insulating Polymer to Improve the Power Efficiency of Electrorheological Fluids.” Pro- ceedings of the 6th International Conference on Elec- trorheological Fluids, Magnetorheological Suspensions and Their Applications, eds. M. Nakano, K. Koyama, 1997, p. 322. [13] Zhao, X. P., Chen, J., Shen, Y. X., Lu, K. Q.: “Properties of Conductive Electrorheological Systems.” Proceedings of the 6th International Conference on Electrorheo- logical Fluids, Magnetorheological Suspensions and Their Applications, eds. M. Nakano, K. Koyama, 1997, p. 302. M. M. Altug Bicak Tel.: +90-212-293 13 00/2510 Fax.: +90-212-245 07 95 e-mail: bicakme@itu.edu.tr H. Temel Belek Tel.: +90-212-2931300/2577 e-mail: belek@itu.edu.tr Ali Göksenli Tel:+90-2122931300 e-mail: goksenli@itu.edu.tr Istanbul Technical University Faculty of Mechanical Engineering Taksim, Istanbul, Turkey 72 © Czech Technical University Publishing House http://ctn.cvut.cz/ap/ Acta Polytechnica Vol. 45 No. 3/2005 Czech Technical University in Prague