AP07_4-5.vp 1 Introduction to ASAC Active Structural Acoustics Control (ASAC) is a treatment for reducing the low-frequency sound radiated by a structure to the far Weld. This method is a combination of two other methods – Active Noise Control (ANC) and Active Vibration Control (AVC). The object of ASAC is similar to that of ANC but the control mechanism is closer to that of AVC. All of these methods use secondary actuators to ensure the desired control criterion – ANC uses sound sources, while AVC uses mechanical force sources. The object of AVC is to minimize (locally or globally) the vibration pattern of a controlled struc- ture [3, 5]. This could increase the total radiated power due to the fluid structure coupling phenomenon. Thus it is not ap- plicable when radiated sound is at the centre of our interest. ANC utilizes the destructive interference of sound waves to achieve its object. This creates zones of quiet in the original sound field, but the overall energy density increases. In cases when we want to reduce radiated sound globally or reduce the total radiated power, other control strategies (e.g. ASAC) must be applied. The total power � radiated by a planar source, e.g., a vi- brating panel, is proportional to the normal velocity of its sur- face, and can be expressed as �( ) ( , ) � � � � � � � � � �� � �� � �� 0 0 2 2 2 2 28 c k V k k k k k k k z x y x y x yd d � � � � , (1) where k is the wave number vector magnitude, kx, ky are its components in the x and y directions, �0 and c0 are air density and phase speed of sound respectively, Vz is the 2D k-space Fourier transform of the normal velocity of the vibrating surface, and � ( ) means the real part of its argument. There- fore by controlling the distribution of the normal velocity over the surface we can control the radiated power. This is the basic idea of ASAC, which acts mechanically on the surface of a vibrating body to change its vibration pattern. 2 Flexural waves in thin plates Let us consider a simple situation – a thin plate radiating sound due to its vibrations. If the thickness of the plate is negligible in comparison with its other dimensions, the most important type of waves (in terms of sound radiation) are flexural waves. Thus we have to solve a twodimensional elastic motion problem. According to thin-plate theory [2, 6], the equation of motion in such a case is EI u h u t p x y t� � � �4 2 2� � � ( , , ) . (2) Where E is Young’s modulus, I is the moment of inertia per unit width, h is thickness of the plate, � is density of the plate, and p(x, y, t) is a general load function (in units of force per unit area). The biharmonic operator � 4 can be expanded in a Cartesian coordinate system into the following form � � � �4 4 4 4 2 2 4 42u u x u x y u y � � � � � � � . (3) Let us consider a rectangular plate clamped on the two shorter sides and free on the other two sides, see Fig. 1. We can write boundary conditions [1] for the clamped sides (at x � 0 and x a� ) � � � � 2 2 3 30 0 u x u x � �, (4) and for the free sides (at y � 0 and y � b) © Czech Technical University Publishing House http://ctn.cvut.cz/ap/ 55 Acta Polytechnica Vol. 47 No. 4–5/2007 The Influence of PZT Actuators Positioning in Active Structural Acoustic Control P. Švec, V. Jandák This paper deals with the effect of secondary actuator positioning in an active structural acoustics control (ASAC) experiment. The ASAC approach is based on minimizing the sound radiation from structures to the far field by controlling the structural vibrations. In this article a rectangular steel plate structure was assumed with one secondary actuator attached to it. As a secondary actuator, a specially designed piezoelectric stripe actuator was used. We studied the effect of the position of the actuator on the pattern and on the radiated sound field of the structural vibration, with and without active control. The total radiated power was also measured. The experimental data was confronted with the results obtained by a numerical solution of the mathematical model used. For the solution, the finite element method in the ANSYS software package was used. Keywords: ASAC, Active radiation control, vibrations, sound radiation. 0 b y a x Fig. 1: Coordinate system orientation of the plate. u u y � �0 0, � � . (5) At the beginning of our analysis, the free vibrations of the plate were solved to obtain modes of the system. For the solu- tion, the ANSYS software package was used. Fig. 2 shows the shapes of the first six modes. 2.1 Forced vibration – shaker load function Let us assume forced vibrations of the plate caused by a harmonic point force source. This condition appears on the right side of equation (2), and it should be written using the Dirac function as f x y t F x x y yi i j t( , , ) ( ) ( )� � �� � �e , (6) where xi and yi are coordinates where the force is applied and the force amplitude F has units of force per unit area. 2.2 Secondary actuator – load function To control sound radiation, secondary actuators have to be applied. For the experiment, an actuator was constructed based on piezoelectric stripe actuators. The stripe actuator was produced by APC International, Ltd [7]. It is a piezo- ceramic (PZT) bending actuator. The actuator consists of two thin strips of piezoelectric ceramic bonded together, with the direction of polarization coinciding. Electrically, the strips are connected in parallel. When an electrical input is applied, one ceramic layer expands and the other contracts, causing the actuator to flex. The stripe actuator has a relatively small blocking force (approximately 0.1–1 N) but a large displace- ment. The maximum displacement is up to 2 mm when the actuator is fixed in a cantilever mounting configuration. The first resonant frequency of the selected PZT strip (Catalog No. 40-1040 [7]) was 70 Hz. To optimize the effect of the stripe ac- tuators, they were clamped to the metal frame in a cantilever mounting. The frame was then attached directly to the steel plate, see Fig. 4. As the piezos oscillate, the bending moment is revealed at the clamped end of the PZT actuator. This moment is transmitted through the frame to the primary structure, acting as a line moment load function [2]. The ef- fect of the added mass of the frame and PZT actuators is almost negligible when active control is turned on, as will be shown below. To describe the effect of the line bending moment acting in the y-axis direction, we should add another term to the right side of equation (2) m x y t M x xk j t( , , ) ( )� � �� �e . (7) The symbol �� ( )x means derivative of the Dirac delta func- tion with respect to its argument, and M is the moment ampli- 56 © Czech Technical University Publishing House http://ctn.cvut.cz/ap/ Acta Polytechnica Vol. 47 No. 4–5/2007 Fig. 2: Shape of the first six modes of the plate mode 1 2 3 4 5 6 f [Hz] 27.6 77.2 99.7 153 206 255.7 Table 1: Frequencies of the first six modes of the plate Fig. 3: Forced vibrations of the plate (point-force actuation at x � 215 mm), f � 125 and 200 Hz, solved by ANSYS fixed end steel plate piezoelectric stripmetal frame Fig. 4: Schematic cross-section of the actuator design and mount- ing on the plate tude (in units of moment per unit length). Finally, we have to solve the equation EI u h u t F x x y y M x xi i j t k j t � � � � � � � � 4 2 2� � � � � � � �( ) ( ) ( ) .e e (8) 3 Experimental setup All experiments were performed in an anechoic room in the acoustical laboratory of the Department of Physics, Czech Technical University in Prague, Faculty of Electrical Engi- neering. In the experiments, a baffled rectangular steel plate was used. The dimensions of the plate were 300×60×0.5 mm and the boundary conditions were as described in the previ- ous sections. An electrodynamic shaker was used as a point force actuator. It was mounted on the plate 215 mm from the origin in the x-direction and 30 mm in the y-direction (the orientation of the plate in the coordinate system is shown in Fig. 1). Only pure harmonic excitation was used. The frequen- cies selected for our experiments were 125 and 200 Hz. The structural vibrations of the plate were measured along the x-axis, in the center-line of the plate for both frequencies and various positions of the secondary actuator (node, antinode). In this first experiment, the active control was set to off, so only the effect of the added mass on the specific locations was observed. Of greatest importance, of course, was the case when the atuator was placed directly on the antinode. In such cases, the vibration pattern was changed. Typically a new local node arises close to the actuator position, see Fig. 6 and Fig. 7. This result corresponds well with the theoretical observa- tions provided by the FEM model, see Fig. 5. The effect of the added mass on the sound radiation was within �3 dB. Com- pared with the effect of active control, this was negligible. Active control was able to reduce the radiated sound pressure level by more than 30 dB with harmonic excitation. © Czech Technical University Publishing House http://ctn.cvut.cz/ap/ 57 Acta Polytechnica Vol. 47 No. 4–5/2007 Fig. 5: Theoretical plate displacement values along the x-axis by the FEM model for single point force actuation and for two positions of the secondary actuator (x � 4 and 12 cm), active control is off Fig. 6: Effect of the added mass of the secondary actuator on the system response – without the actuator, and with it placed on the node and antinode at f � 125 Hz Fig. 7: Effect of the added mass of the secondary actuator on the system response – without the actuator, and with it placed on the node and antinode for f � 200 Hz Fig. 8: Vibration pattern for f � 200 Hz with active control (AC on), actuator placed on the node – marked by the hatched cross on the x-axis, the black cross marks the position of the shaker In Figs. 8 and 9, the actuator was placed on the node and antinode, respectively. The vibration pattern was measured with the active control turned off (AC off) and then with the active control turned on (AC on). The dashed curve shows the forced vibrations of the primary structure without the actua- tor mounted on it. The displacement amplitudes increased overall, while the minimum sound pressure level was ob- served. This result is in good accordance with fluidstructure coupling theory and with the theoretical discussion presented in this paper. 4 Conclusion This paper presents theoretical and experimental studies of thin plate vibrations and the effect of an added secondary actuator which controls the structural response of the system to minimize radiated sound. The results show that a piezo- electric stripe actuator attached to the plate in a cantilever mounting is able to control the radiation effectively and al- most independently of its position. The mass added to the plate (due to the actuator mounted on it) has its most signifi- cant effect on the mechanical response when placed between two nodal lines (on the maximum of the standing wave – antinode). In this case, the vibration pattern is changed and a new nodal line arises close to the position of the mounted actuator. This conclusion corresponds well with the FEM model results. However, when the position of the actuator mounting is on the nodal line, the vibration pattern stays the same, as we had expected. When active control is turned on, both positions of the actuator lead to a decrease in the sound pressure level. The total radiated power decrease, measured with an intensity probe, is 10 dB. Acknowledgments The research reported in this paper was supervised by Prof. O. Jiříček, FEE CTU in Prague, and was partially sup- ported by research program MSM6840770015. References [1] Brdička, M., Samek, L., Sopko, B.: Mechanika kontinua, Academia, Praha, 2000, p. 358–371. [2] Fuller, C. R., Elliot, S. J., Nelson, P. A.: Active Control of Vibration, Academic press, London, 1997. [3] Johnson, B. D., Fuller C. R.: Broadband Control of Plate Radiation Using Piezoelectric, Double-Amplifier Active-Skin and Structural Acoustic Sensing. Journal of the Acoustical Society of America, Vol. 107 (1999), No. 2, p. 876–884. [4] Wiliams, E. G.: Fourier Acoustics Sound Radiation and Nearfield Acoustical Holography, Academic press, London, 1999. [5] Fuller, C. R.: Active Control of Sound Radiation from Structures: Progress and Future Directions. Active 2002, Southampton. [6] White, R. G., Walker, J. G.: Noise and Vibration, Ellis Horwood Publishers, Chichester, 1982. [7] APC International Ltd.: Piezoelectric Ceramics: Principles and Applications, Mackeyville, USA, 2002. Ing. Petr Švec e-mail: svecp1@fel.cvut.cz Ing. Vojtěch Jandák e-mail: jandav1@fel.cvut.cz Department of Physics Czech Technical University in Prague Faculty of Electrical Engineering Technická 2 166 27 Praha 6, Czech Republic 58 © Czech Technical University Publishing House http://ctn.cvut.cz/ap/ Acta Polytechnica Vol. 47 No. 4–5/2007 Fig. 9: Vibration pattern for f � 200 Hz with active control (AC on), actuator placed on the antinode – marked by the hatched cross on the x-axis, the black cross marks the posi- tion of the shaker Fig. 10: Sound field 30 cm above the baffled plate at frequency 200Hz, active control is turned on