Impaginato 43 Adv. Hort. Sci., 2021 35(1): 43­51 DOI: 10.36253/ahsc­9609 A new pneumatic harvester for improvement and facilitation the harvesting of the olive fruits F. Zare 1, G. Najafi 1 (*), T. Tavakoli Hashjin 1, A.M. Kermani 2, P. Ghiasi 1 1 Biosystems Engineering Department, Tarbiat Modares University (TMU), Tehran, Iran. 2 Department of Agro‐Technology Engineering, College of Aburaihan, University of Tehran, Tehran, Iran. Key words: collector systems, harvesting damage, manual harvest, mechanical harvesting, olive tree. Abtract: The objective of this study was to measure and evaluate the perfor­ mance of a New Pneumatic Harvester (NPH) for harvesting the olives fruit and compare the results with those of similar cases. The study involves two sec­ tions, namely, the NPH and the collector system. Two oily types of olive (‘Mari’ and ‘Yellow’) were selected to evaluate the NPH and the collector system. The randomized complete block design and Duncan’s multi­scope test were used for variance analysis and means comparison purposes, respectively. The depen­ dent parameters used to evaluate the NPH were harvesting productivity, har­ vesting efficiency, and leave downfall percent. Also, the fruit damage was selected for the collector system. Results showed that the NPH can harvest 92% of olive fruits. The highest amount of harvesting productivity belongs to NPH of 29.47 kg/h. The percent of leaves downfall in the harvesting process was found to be 2.55%. Using the collector system can reduce the level of damaged fruit from 60.8% to 25.12% and from 60.54% to 24.54% in the Mari and Yellow vari­ ety. 1. Introduction The olive tree is one of the Mediterranean plants that its fruits used as a cannery and oil extraction (Barbera et al., 2013). Olive has traditionally been known among people, which is also important for health and used as a strategic food in some countries (Fiorino et al., 2010). One of the major problems with the olive plant is harvesting which is mostly done in different ways: (a) picking up the fruit on the ground (b) harvesting manually (c) harvesting via branch shaker (d) harvesting mechanically (Lupi et al., 2012). Harvesting is the final step in field pro­ duction of olive fruits, but if done at the wrong time or in the wrong way it can markedly affect the grower’s net return. The economic success of super­intensive olive plantations is mainly achieved due to the full mecha­ nization of harvesting (Ottanelli et al., 2019). The olive harvest is expen­ (*) Corresponding author: g.najafi14@modares.ac.ir Citation: ZARE F., NAJAFI G., TAVAKOLI HASHJIN T., KER­ MANI A., GHIASI P., 2021 ­ A new pneumatic har‐ vester for improvement and facilitation the har‐ vesting of the olive fruits. ­ Adv. Hort. Sci., 35(1): 43­51 Copyright: © 2021 Zare F., Najafi G., Tavakoli Hashjin T., Kermani A., Ghiasi P. This is an open access, peer reviewed article published by Firenze University Press (http://www.fupress.net/index.php/ahs/) and distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited. Data Availability Statement: All relevant data are within the paper and its Supporting Information files. Competing Interests: The authors declare no competing interests. Received for publication 14 July 2020 Accepted for publication 27 January 2021 AHS Advances in Horticultural Science https://doi.org/10.36253/ahsc-9609 http://www.fupress.net/index.php/ahs/ http://creativecommons.org/licenses/by/4.0/ http://creativecommons.org/licenses/by/4.0/ http://creativecommons.org/licenses/by/4.0/ Adv. Hort. Sci., 2021 35(1): 43­51 44 sive in terms of wages and adequate labor supply has brought about many problems (Zipori et al., 2014). Fruit damage, damages related to the olive tree, quality reduction, human injuries, time consumption, and costly process in the traditional ways are prob­ lems existing in the harvesting process. Mechanized harvesting is done in many different types, such as the trunk and limb shakers. Because of device fea­ ture like power supplement implementation of this shakers are difficult (Çakmak et al., 2011). Although, the mechanized harvesting methods are very effi­ cient but they have an high usage costs. Therefore, the best harvest system should be inexpensive and highly efficient. Designing of shakers, harvesting efficiency analyz­ ing and tree damage for olive fruits are the attractive topics in the mechanization field, so in this regards researchers studied the effect of shaking force and the amplitude of the shaking on the mechanized har­ vesting of olive. They showed that an increase in olive tree diameters trunks led to an increase in shak­ ing force and a decrease in amplitude of the shaking. So, for mechanized harvesting in the big olive trees with big trunk diameters more power must be applied (Babanatsas et al., 2019). A comparative study was done to investigate the various ways of olive harvesting. Results show that harvesting through shaking the stem is the best way to remove the olive fruit from a tree (Yousefi et al., 2010). Five different olive harvesters were investigated. The flat type olive harvester has more vibration value index (Çakmak et al., 2011). The effect of two types of olive tree harvesting (Trunk Shaker and Mechanical Harvest Aid) on harvesting time were studied. Results show that harvesting the olive trees with mechanical harvest aid can save more time (Nayeri and Torkashvand, 2016). Results concerning the examina­ tion of harvesting type on harvesting efficiency show that with increasing the fruit removal force the har­ vesting efficiency was decreased (Zipori et al., 2014). A study on four types of olive harvester; plastic combs, small shakers, rotating combs, and vibrating combs were done. Researchers indicated that all types of harvesters except the small shaker improve the worker’s productivity (Bentaher and Ben Rouina, 2002). Results of the study on a pneumatic harvester showed that manual harvesting and mechanical har­ vesting methods had a significant effect. The pneu­ matic comb machine had higher bruised fruit than the manual harvesting (Ahmad, 2018). With an increase in the operating velocity, the productivity harvesting and damage percentage increased and the 1250 rpm operating velocity value could be a good alternative for harvesting (Mansour et al., 2018). Two methods of harvesting olive fruit, namely, mecha­ nized harvesting with Pneumatic Harvester (PH) and Manual Harvesting (MH) were investigated, which indicated that due to the presence of the collector system, using mechanized harvesting can reduce the fruit damages (Plasquy et al., 2019). Mechanical canopy and trunk shaking were investigated in line with the harvesting mechanization of table olive orchards. Accumulating the trunk shaker and shaker combs can increase the bruise index of olive fruits. The lowest bruise index of olive fruits belongs to the manually­type harvest with a 0.5% value (Sola­ Guirado et al., 2020). The designing and fabrication of olive fruit har­ vester have long since been the subject of many types of research. Applying some of these systems may exert large costs on farmers, and the efficiency of these machines requires significant economic costs that many producers cannot afford. For this large group of farmers, new models have recently been presented. Nevertheless, the use and utility of some of these machines still entail difficulties, such as the large weight, difficult access to the trunks, or handling the fruit boxes. In this study, results con­ cerning the evaluation of a new design of portable pneumatic olive harvester with a fruit collector sys­ tem are presented to fix some of the harvesting problems. The evaluation parameters of harvesting machine (such as: the harvesting efficiency, harvest­ ing productivity, and olive tree damage) were com­ pared both with the manual method and similar har­ vesting methods. Finally, the effect of fruit collector on fruit damage was investigated. 2. Materials and Methods Vegetal material Two different varieties (‘Mari’ and ‘Yellow’) of olive fruits were selected to evaluation that both of them are Iranian variety and commonly grown for oil and canned production. The first step in designing a new harvesting machine is cognition about crop char­ acteristics such as detachment force from tree branches. For measuring fruit detachment force from tree branches, three tree of each verity were select­ ed and ten olive fruits of each tree accidentally were selected. The force required to detach them was Zare et al. ‐ A new pneumatic harvester for olive fruits harvesting 45 measured by a mechanical force gauge. The mechani­ cal gauge of FG­5020 model was used and calibrated in the Precision Process Calibration Laboratory with the approval of No. 681 of the Standard Institute of Iran. The fruit detachment force employed to deter­ mine the applied force on the pneumatic jack. So to determine this amount assuming that all of the jaw surface covered by the olive fruit and the detach­ ment force in this situation was calculated. Tests were conducted in the Ashrafieh gardens in Qazvin province in Iran and the fruit ripening index was 4.52%. The age of olive trees was 20 years and the height of trees was up to 3.5 m. Harvester machine design The pipe diameter is a very important factor for designing pneumatic systems. When the low pipe diameter was applied, the pressure dropped and the airflow velocity increased accordingly. In the case of water penetration into the pipe, the clogged pipes situation was expected to happen. Two conditions, namely, 5­8 m/s and 0.5 bar were found to be appro­ priate for the airflow velocity and the pressure dropped. The first step for jack design is to define the required pressure and velocity of air to detach the olives from the tree. Equation (1) shows the jack pis­ ton, which was used to calculate the air force. Fm = P x a (1) After selecting jaws frequency and active volume of the piston, the cam length and Air Mass Flow (AMF) were calculated. The amount of AMF for jaw movement to open the jaw was calculated by equa­ tion (2), and in the closed cycle, equation (3) was used for the AMF. Finally, the total AMF to open and close the jaws was calculated by equation (4). Qext = p x (D2/4) x c x n x (P1 ‐ P0)/P0 (2) Qret = p x [(D2­d2)/4] x c x n x (P1 ‐ P0)/P0 (3) Qtot = p x [(2D2­d2)/4] x c x n x (P1 ‐ P0)/P0 (4) Assuming that the total pneumatic energy was converted to the kinematic energy, the maximum velocity could be determined using Equation (5). E = ½ m (nmax) 2 (5) The total energy required was calculated by equa­ tion (6). E = [½ P x pD2 x m (0.5)2] / (2g x 4) (6) The total energy for opening the jaw was calculat­ ed by equation (7): E = 5 x 10­4 x P (D2 ‐ d2) (7) The determinations show that the detachment force of olive fruit from the tree and the pressure required for the pneumatic jack were 10 N and 7 bar, respectively. The machine had one handle and it was gripped by one operator’s hand and a telescoping rod up to a maximum length of 3 m. The harvesting mechanism had two jaws and each jaw contained 7 fingers that allowed for easy and deep access to all types of foliage without getting caught in the branch­ es. 90 degrees was selected for the angle between two jaws based on the previous researches. The jaws had 18 cm length and the distance between them must be equal to the olive fruit width, so 1 cm dis­ tance was considered. We assume that in every impact of jaws, 23 olive fruits were detached from tree branches. So, the total force required for each impact was determined. The force related to the pneumatic cylinder was determined by equation (8). 2fd Cos (Ɵ/2) = F (8) The amount of force of each jaw for the olive fruit detached from the tree was 325.3 N, and for calculat­ ing the piston diameters equation (9) was used. F = A x P (9) After determining the piston diameters, the length of the cam was calculated and the standard jack with these characters was selected. The cylinder provides a closed system which assists the movement of the piston. For moving the piston across the cylinder in high frequency, valves must be used or the manual control applied. Because of the operation conditions, the pneumatic valve was selected to change the airflow direction. When the pneumatic valve was in position A, high air pressure pushed the piston to the right side (Fig. 1). By moving the piston to right, the airflow was transferred to the C input of the pneumatic valve which changed the direction of airflow, resulting in the activation of the B position of the pneumatic valve. When high­pres­ Adv. Hort. Sci., 2021 35(1): 43­51 46 sure air moves to the B output of the pneumatic valve, the piston moves to the left side, and air moves toward the D input of the pneumatic valve, and such a cycle is replicated. After assembling the parts, the frequencies of these cycles were measured by an electronic eyes sensor. The frequency of the piston movement is 5.21 Hz in 7 bar air pressure. So, after defining design parameters, the mechanical value of No. G1/8’’ was selected. Other parts of the harvester such as the chain, cam, and pneumatic value along with the parts were designed. Figure 2 shows the details of NPH, including har­ vester jaws, cylinder and pneumatic valve, power transmission, and telescoping rod. The common properties of the collector system for olive fruit are shown in Table 1. By applying this system, the olive fruits falling from the tree were col­ lected into a box. The driving power of the collector system are provided by labor. It is possible to conclude from figure 3 that the collector system is ready to collect the fruits in the box. The collector system includes the wheels, steer­ ing wheel, bendable bars, wire for hold cover, poly­ ester cover, trunk holder, position for boxes, and out­ let, all of which are assembled on chassis. Statistical design The variance analysis was done in randomized complete block design with three replicate and the statistical computations as well as analyzing the data were performed by the MSTAT­C software. Duncan’s multi­scope test was used for comparison of the means. The performance of the developed harvest machine was measured by the Harvesting Productivity (HP), harvesting efficiency (HE), and leaves downfall per­ cent (LD). The performance of the developed collec­ tor system was measured by the olive fruit damage (FD). For measuring the harvesting productivity of olive fruit harvester, the total mass of detachment fruits was recorded using the machine. The total har­ vesting time includes selecting, detaching fruit, and the time required for moving machine between olive trees inside the field. The productivity of the operat­ ed harvester was calculated using equation (10) (Polat et al., 2007): HP = k1/T (10) Harvesting efficiency was calculated by equation (11) (Srivastava et al., 2006). HE = [k1/(K2 + K1)] x 100 (11) Fig. 1 ­ Schematic of the piston, cylinder, valve, and connector pipes Fig. 2 ­ The different parts of the new pneumatic harvester. Table 1 ­ Collector system properties Parameters Value Chasses length 140 cm Chasses width 95 cm Trunk holder height 60 cm Trunk diameter up to 40 cm Cover diameter 300 cm Fig. 3 ­ Collector system parts. Zare et al. ‐ A new pneumatic harvester for olive fruits harvesting 47 The percent of olive leaves downfall is defined as the percent of branches and leaves fall down by the harvester and was calculated by equation (12): TD = Mbl/ Mtbl x 100 (12) The total weight of branches and leaves of the olive trees previously measured. Some trees that had to be removed were collected and weighed separately, finally the means weight of the branches and leaves of three trees were used in the equation (12). Fruit damage includes the visual inspection and the fruit appearing broken to the naked eye. Fruit damage was calculated by equation (13). FD = Md/ Mt x 100 (13) The main criteria for designing the New Pneumatic Harvester (NPH) were as follows: easy design, simple to use, low weight, high productivity, less fruit damage, and low operating costs. The main novelty of this type of harvester is low operating costs and use in gardens far from the energy net­ works. A double­sided jack was used to provide jaw movement so, the required airflow rate, pressure drop, airflow control valve, and jack size must be defined. To show the advantages and disadvantages of the present device with existing devices, the results of the evolution of the NPH compared with a Pneumatic Harvester (PH) that the features of the PH are shown in Table 2. 3. Results and Discussion Results of the harvesting tests Harvesting productivity was calculated among 3 types of different harvesters’ system (MH, PH and NPH), using the equation number “10” (Table 3). Results showed that the three harvesters have a sig­ nificant difference at 5% levels of probability. Due to different treatments, the means were compared and the NPH was found to have more HP placed in a group (a) with an amount of 29.47 kg/h. The PH was placed in a group (b) with an amount of 21.33 kg/h and the MH was placed in a group (c) with an amount of 9.37 kg/h. Figure 4 shows the HP means for three harvest methods. Due to the special properties of NPH such as the power of vibration, frequency, and shape of a bar, the HP of this machine was more when com­ pared to two other methods of harvesting. Kermani (2016) indicated that the mounted branches shaker machine has 130.72 kg/h of HP, but it fails to be used in traditional gardens. This type of harvester needs a tractor to perform, which is not feasible for small gar­ dens (Kermani, 2016). Table 4 shows the results of variance analysis related to the difference between two types of har­ vesting machine concerning the Harvesting Efficiency (HE). The analysis shows that the effect of machine type on HE is significant at 1% probability. The pneu­ matic harvester can detach 86% of olives from the tree, but NPH shares 92% of HE. Because of the avail­ ability of all olives on the tree, the HE of this method Table 2 ­ PH technical features Number Feature Amount 1 model Campagnola srl 2 weight 1 kg 3 length 1.8 ­ 3 m 4 Max pressure 7 bar Table 3 ­ Result of variance analysis velocity (m s­1) for harvest­ ing productivity Parameters df Sum of squares Means of squares F Block 2 34.925 17.462 1.6126 * Harvest method 2 283.554 141.777 13.093 * total 4 43.314 10.828 CV 25% Fig. 4 ­ Harvesting productivy means for three harvesting methods. NPH= New pneumatic harvester; PH= pneuma­ tic harvester; MH= manual harvesting. * = significant at 5% of probability. ** = significant at 1% of probability. NS = not significant. 48 Adv. Hort. Sci., 2021 35(1): 43­51 is considered as 100% for labor in the case of manual harvest (Fig. 5). It is very important to understand how to place the harvesting head on the telescoping rod. The angle between the harvester head and telescoping rod in the NPH is fixed and the jaws move between 123 to 213 degrees, and such a property differs from the PH. The other important difference resulting in increased HE is the jaws speed, where they move quicker in NPH compared to the PH. Some places of olive fruits on the tree are not available for NPH and PH. The harvester rod plays the important role in the HE. Whatever the harvesters rod has high maneuver­ ability the more olive fruits can detected and the HE increased. Kermani (2016) showed that the olive tree branches shaker machine has 84.51% HE, but com­ pared to other machines, the leaves downfall percent in this harvesting method is high (Kermani, 2016). Equation 12 was used to determine Leaves down­ fall percent (LD). After harvesting, all the branches and leaves were collected and weighted. By increas­ ing in branches and leaves that fall from the tree the LD was increased. Table 5 shows the variance analy­ sis among the three harvesting methods and olives types. The effect of variety (type) on LD was not sig­ nificant, but harvesting methods have a significant effect on LD. Figure 6 shows the LD for three harvest­ ing methods; NPH has more LD than the two other harvesting methods. The speed of jaws in the PH is 1080­1150 rpm, while in the NPH the minimum speed of jaws is 1290 rpm. This difference in jaws speed led to an increase in the leaves’ downfall per­ cent. Comparison of the means of harvesting method shows that the NPH with an amount of 2.52% LD has the highest detachment of leaves from the tree. The PH and MH were not significantly different, and they were placed in a group (b). The electrical rotation bar in Kermani’s (2016) research has the highest LD with a 2.20% damage (Kermani, 2016). Due to the prob­ lems with the head location on the handle in the NPH, the amount of LD was increased, however, such a problem can be surmounted. Table 4 ­ Result of variance analysis of for harvesting efficiency Parameters df Sum of squares Means of squares F Between data 1 717.883 717.838 118.644 ** Inside data 4 24.203 6.05 CV 3.25% Fig. 5 ­ Harvesting efficiency means for three harvesting methods.NPH= New pneumatic harvester; PH= pneuma­ tic harvester; MH= manual harvesting. Table 5 ­ Result of variance analysis for leaf downfall Parameters df Sum of squares Means of squares F Block 2 0.286 0.143 42503 NS Harvest method 2 1.006 0.503 14.934 * total 4 0.135 0.034 CV 8.93% Fig. 6 ­ Leaf downfall (%) means for three harvesting methods. NPH= New pneumatic harvester; PH= pneumatic harve­ ster; MH= manual harvesting. * = significant at 5% of probability. ** = significant at 1% of probability. NS = not significant. * = significant at 5% of probability. ** = significant at 1% of probability. NS = not significant. Zare et al. ‐ A new pneumatic harvester for olive fruits harvesting 49 Product quality results with the use of the collector system Olive fruits fall on the ground after harvesting and get damaged as a result of this matter. To prevent the olive fruits from damage, a collector system gath­ ering the fruits into the box was designed and manu­ factured. For evaluating the collector system, two types of olive trees were harvested with the new pneumatic harvester, and the percent of damaged and undamaged olive fruits were investigated. Table 6 shows the damaged and undamaged olive fruit in the NPH with the collector systems and manual har­ vest without the collector system. Results show that the use of a collector system can decrease the fruit damage (FD) from 60.80% to 25.12% in the ‘Mari’ variety. Similar results were achieved for the ‘Yellow’ variety. Table 6 shows the damaged and undamaged olive fruit for the harvest­ ing of ‘Yellow’ olive fruit variety in the two harvesting methods. Figure 7 shows the injured, bruised, and uninjured olive fruit percent in fourteen measured samples for the manual harvest. Due to the differ­ ence in the weight of olive fruits, the percent of each group shown was based on the number and weight of olive fruits. In the manual harvest, a large portion of the fruits of the olive falls on the ground, then picked up and collected into the box. This process led to the bruising of more than half of the olive fruits. Table 7 shows the means, standard deviation, aver­ age deviation, variance, minimum and maximum of weight along with the number of injured, bruised, and uninjured olive fruits in MH and NPH. Results show that after harvesting the fruits of the olive in the manually harvest method, 45.29% of olives fruits were bruised. Bruising occurred on the skin of the olive fruits as a result of fruit hitting on the soil. Also, the injuring situation occurred when fruits were hit by sharp branches or stones. The percent of injured, bruised, and uninjured olive fruits for NPH based on the number and weight is shown in figure 8. The results improved significant­ ly. Most parts of the olives fruit had no injury in the harvesting process. Olive fruits that were detached from the tree fall in the collector systems and avoid contact with the stones or the soil/ground. Table 7 also shows the results of measuring related to the injured olive fruit parameters. The means of unin­ Table 6 ­ Damaged and undamaged fruits in two types of harvesting method in Mari and Yellow variety Cultivar Manual harvesting New pneumatic harvester Undamaged fruit (%) Damaged fruit (%) Undamaged fruit (%) Damaged fruit (%) Mari 39.2 60.8 74.88 25.12 Yellow 39.45 60.54 75.45 24.54 Fig. 7 ­ Illustration of the injured, bruised, and no injured olive fruit in the manually harvest. Harvesting type Number of injured olives Weight of injured olives Number of bruised olives Weight of bruised olives Number of no injured olives Weight of no injured olives Manual harvesting 14.87±1.70 * 15.51±1.71 45.42±2.04 45.29±1.98 39.71±1.95 39.20±1.87 New pneumatic harvester 7.98±1.14 8.33±1.36 15.98±2.75 16.79±2.79 76.02±2.96 74.88±2.98 Table 7 ­ Results of measuring the injured parameters for the olive fruits in manual harvesting and new pneumatic harvester * Means ± standard deviation. Adv. Hort. Sci., 2021 35(1): 43­51 50 jured olive fruits in the NPH increased from 39.71% to 76.02%. This means that the NPH was able to save almost half of the olive fruits. The jaws hitting olive fruits and detached fruits from brunches after that fruits falling from the tree and collide with the branch and trunk of the tree. This process caused almost 24% damage to the olive fruits. 16% of the olive fruits in the harvesting process were bruised and the rest of the damaged fruits got the ruptured skin, which was then classified as the injured fruits. 4. Conclusions Harvesting is one of the important steps in the olive farming and the device that used also strongly effected on the quality of the harvesting. In this study, tried to investigate the New Pneumatic Harvester performance to show its advantage in compared with other pneumatic harvesters that exist in the market. When considering the fruit ripening index of 4.52%, one can say only 8% of olive fruits remained on the trees. On the other hand, the amount of HP was 29.47 kg/h. This result shows that NPH can detach 92% of olives on the tree in a short time. In the case of the traditional and small gardens, this machine is very practical because it can work effectively in the garden in different situations. The collector system saves more time and prevents olive fruit from damage and can be easily used for every harvesting method. Acknowledgements This research was supported by Iran National Science Foundation (INSF) with 92032254 number. We thank our colleagues from INSF who provided insight and expertise that greatly assisted the research. References AHMAD R.L., 2018 ­ Efficiency of mechanical tools for olive harvest and effect on fruit quality. ­ Acta Horticulturae, 1199: 315­319. BABANATSAS T., GLAVAN D.O., BABANATIS MERCE R.M., GLAVAN A.I., 2019 ­ Study of forces influencing the shaking parameters in mechanized/robot‐assisted har‐ vesting of olives. ­ MATEC Web of Conferences, vol. 290, pp. 03001. BARBERA A.C., MAUCIERI C., CAVALLARO V., IOPPOLO A., SPAGNA G., 2013 ­ Effects of spreading olive mill waste‐ water on soil properties and crops, a review. ­ Agric. Wat. Manag., 119: 43­53. BENTAHER H., BEN ROUINA B., 2002 ­ Mechanical harvest‐ ing of ‘chemlali de sfax’ olive‐trees. ­ Acta Horticulturae, 586: 365­368. ÇAKMAK B., SARAÇOĜLU T., ALAYUNT F.N., ÖZARSLAN C., 2011 ­ Vibration and noise characteristics of flap type olive harvesters. ­ Appl. Ergonomics, 42(3): 397­402. FIORINO P., MARONE E., OTTANELLI A., 2010 ­ Mechanical harvesting, productivity and superintensive planting systems in olive groves. ­ Adv. Hort. Sci., 24(1): 91­94. KERMANI A., 2016 ­ Comparison of four harvesting machines for harvesting of oil olive. ­ J. Engineering Res. Agric. Mechan. Systems, 16(65): 1­18. LUPI F.R., GABRIELE D., FACCIOLO D., BALDINO N., SETA L., DE CINDIO B., 2012 ­ Effect of organogelator and fat source on rheological properties of olive oil‐based organogels. ­ Food Res. Inter., 46(1): 177­184. MANSOUR H.A., ELMESIRY T.A., ABDELHADY A.A., 2018 ­ The effect of operating speed and olive varieties har‐ vested by hand‐held machine on productivity and dam‐ age percentage. ­ World Wide J. Multidisc. Res. Develop., 4(2): 355­360. NAYERI F., TORKASHVAND A.M., 2016 ­ Techno‐economic efficiency of trunk and mechanical harvest aid shakers for harvesting olive fruits in Guilan Province, Iran. ­ Inter. J. Agric. Manag. Devel. (IJAMAD), 6(3): 273­280. OTTANELLI A., MARONE E., FIORINO P., 2019 ­ A new device to improve the mechanical winter pruning in olive trees hedgerows. ­ Adv. Hort. Sci., 33(1): 113­122. PLASQUY E., SOLA­GUIRALDO R.R., FLORIDO C., GARCÍA J.M., BLANCO­ROLDÁN G., 2019 ­ Evaluation of a man‐ ual olive fruit harvester for small producers. ­ Res. Agric. Engineering, 65(4): 105­111. POLAT R., GEZER I., GUNER M., DURSUN E., ERDOGAN D., BILIM H.C., 2007 ­ Mechanical harvesting of pistachio nuts. ­ J. Food Engineering, 79(4): 1131­1135. Fig. 8 ­ Schema of the injured, bruised, and no injured olive fruit in harvesting with new pneumatic harvester. Zare et al. ‐ A new pneumatic harvester for olive fruits harvesting 51 SOLA­GUIRADO R.R., CASTILLO­RUIZ F.J., BLANCO­ROLDAN G.L., 2020 ­ Mechanical canopy and trunk shaking for the harvesting mechanization of table olive orchards. ­ Revista Facultad Ciencias Agrarias, UNCuyo, 52(2): 124­ 139. SRIVASTAVA A.K., GOERING C.E., ROHRBACH R.P., BUCK­ MASTER D.R., 2006 ­ Engineering Principles of Agricultural Machines. ­ Amer.Soc. Agric. Biol. Engineers, Second Edition, St. Joseph, MI, USA. YOUSEFI Z., ALMASSI M., ZEINANLOO A.A., MOGHADASI R., KHORSHIDI M.B., 2010 ­ A comparative study of olive removal techniques and their effects on harvest productivity. ­ J. Food, Agric. Environ., 8(1): 240­243. ZIPORI I., DAG A., TUGENDHAFT Y., BIRGER R., 2014 ­ Mechanical harvesting of table olives: Harvest efficien‐ cy and fruit quality. ­ HortSci., 49(1): 55­58.