Al-Khwarizmi Engineering!!! Journal Al-Khwarizmi Engineering Journal, Vol. 7, No. 2, PP 14 - 21 (2011) The Effect of the Solution Heat Treatment on the Mechanical Properties of Aluminum-Copper Alloy (2024-T3) Using Rolling Process Hani Aziz Ameen * Asma Hassan Ismail ** Khairia Salman Hassan *** * Department of Dies and tools Engineering/ Technical College/ Baghdad E-mail: Haniazizameen@yahoo.com ** Department of Mechanical Engineering/ College of Engineering/ University of Baghdad E-mail: asma.sawaf@yahoo.com *** Department of Mechanic/ Institute of Technology/ Baghdad E-mail: almaden20002000@yahoo.com (Received 2 August 2010; accepted 19 April 2011) Abstract The effect of solution heat treatment on the mechanical properties of Aluminum-Copper alloy. (2024-T3) by the rolling process is investigated. The solution heat treatment was implemented by heating the sheets to 480 C° and quenching them by water; then forming by rolling for many passes. And then natural aging is done for one month. Mechanical properties (tensile strength and hardness) are evaluated and the results are compared with the metal without treatment during the rolling process. ANSYS analysis is used to show the stresses distribution in the sheet during the rolling process. It has been seen that good mechanical properties are evident in the alloy without heat treatment due to the strain hardening and also the mechanical properties are improved after heat treatment and rolling process but with lower forces and stresses when compared with the untreated. Keywords: Forming process, rolling, heat treatment, ANSYS. 1. Introduction The ability to use the rolling processin different industries purposes depends on whether the metal is ferrous or non ferrous. This is because of the different mechanical properties, e.g., strength, ability of plastic forming and physical properties like thermal, electrical and magnetic conductivities. From the important things for choosing the suitable metal for production is having confined chemical construction and good ability for plastic forming in order to take the desired form without changing the chemical instruction of metal experimentally. Due to the ability of plastic forming of metal by applying confined force related with the volume and shape of the product, the procedures are various depending on the way of applying the force; these procedures are: rolling, dragging, extrusion, bending and shearing. Wang (2009), studied the alloy (Al–10.8Zn–2.8Mg–1.9Cu) synthesized by the spray atomization and deposition technique. Microstructure and mechanical properties of the spray-deposited alloy processed through hot rolling and heat treatment were investigated by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction and tensile test. The results indicate that the microstructure of the spray-deposited alloy is mainly composed of the Al matrix and the Mg(ZnCu)2 compounds. The fragmentation of the Mg(ZnCu)2 phases in the alloy has been regarded as one of the main feature during hot rolling. After solution treating, the microstructure is found to be composed of the Al matrix and a spot of Al7Cu2Fe, Al9FeNi compounds. The spray- deposited Al–Zn–Mg–Cu alloy in the T6 temper displays superior strength due to the presence of two types of coherent GP zones (spherical GPI zones and thin platelet GPII zones). Shahani et al, (2009), parametrically studied hot rolling process by the finite element method of AA5083 This page was created using Nitro PDF trial software. To purchase, go to http://www.nitropdf.com/ http://www.nitropdf.com/ Hani Aziz Ameen Al-Khwarizmi Engineering Journal, Vol. 7, No. 2, PP 14 - 21 (2011) 15 aluminum alloy. Chandramohan et al (2009) made a review for of rolling process with ohsas and texture formation. This study investigates the effect of solution heat treatment on the mechanical properties using rolling process is. 2. Calculating the Force and Energy Required for Rolling Process The required force for rolling in simple rolling mechanism with two rollers could be calculated as shown in Fig. (1) by equation (Nagpal,1998) : Fr = L W σ QP …(1) Fig.1. Dimensions of Rolling Process. From Fig.(1), it is seen that the output speed is greater than the input speed for the constant speed of rollers and there is one point of contact angle (α) in case of the sheet and rollers moves in the same speed. Due to this process the friction force affects at the neutral point therefore it is important for rolling which cause to reduce the energy from the rollers caused forming. If the friction coefficient of roller approaches to zero, the roller will slide on sheet, the means no forming will be done, so that the lubrication must be controlled during the rolling process to prevent skidding ( Johnson and Needham,1982) . The force during the rolling process could be calculated related to the contact line measured from equation (2). L= √R(ho – hi) …(2) In the case of (h/L<1), the roller diameter is bigger when compared with the sheet thickness and the plastic deformation will be plane strain case and homogeneously and the rolling pressure can be determined from Pr = σ tm QP …(3) Hence, the force is equal to Fr =L w σ tm QP …(4) In spite of that the length increases along the rolling but the width will be constant if (w/h>10) is for the most rolling processes. From equation (4) it is seen that the decrease in contact length (L) by decreasing the radius of roller made the required force decrease . In case of (h/L>1) which means that the sheet thickness is bigger when compared with roller radius therefore the non homogeneous forming occurrs, because of sticking which is undesired, but it happens in rolling process for big blocks, and pressure could be obtained in this case by(Johson and Miller,1973); Pr = σ tm Qi …(5) The non homogeneous deformation could cause cracking defect in the condition of; 18.1*)1(  i oo h h R h …(6) The torque of roller obtained from T=Fr L …(7) The roller power could be determined by; Power = ω T …(8) where ω is the angular velocity determined from; ω = V / R …(9) 3. Experimental Part 3.1. Alloy Selection Aluminum alloy (2024-T3) had been selected treatable because an employment in many engineering applications such as air transmission structures. To check up the chemical instruction of metal alloy, chemical analysis had been done by spectrometer and the results explained in table(1). This page was created using Nitro PDF trial software. To purchase, go to http://www.nitropdf.com/ http://www.nitropdf.com/ Hani Aziz Ameen Al-Khwarizmi Engineering Journal, Vol. 7, No. 2, PP 14 - 21 (2011) 16 1.5 mm 2 0m m 100m m Table 1, Chemical Instruction for Aluminum Alloy (2024-T3). Element Al Ti Cr Zn Si Fe Mn Mg Cu Real Value 92.6 0 0.05 0.1 0.4 0.3 0.6 1.5 4.4 Standard Value 0-0.15 0-0.1 0-0.25 0-0.5 0-0.5 0.30-0.9 1.2-1.8 3.8-4.9 However the mechanical properties illustrated in table(2), where the available alloy sheet was formed as a plate having 10mm thickness to be suitable for deferent conditions research like making rolling processes experiments in deferent rates. Table 2, Mechanical Properties of Aluminum Alloy (2024- T3). ρ (Kg/m3) Elongation EL.% U MPa y MPa (proof stress 0.2%) 280010%483414 3.2. Preparing Sheets for Rolling The dimension of the rolling sheet is shown in Fig.(2). Fig.2. Specimen Dimensions. Table 3, Classification of Used Sheets. Specimen symbol Case AThe basic material BRolled without heat treatment B1Rolled to 1.4mm B2Rolled to 1.275mm B3Rolled to 1.2mm B4Rolled to 1.1mm CSolution treatment before rolling 3.3. Classification of Sheets After cutting the sheets they had been classified into groups shown in table (3). 4. Heat Treatment Solution Solution heat treatment had been done for sheets (type C) where the sheets are heated to 480 C° temperature then cooled quickly (quenching ) by water. 5. Rolling Process Rolling process had been done for sheets (types B & C) from table (3) by rolling machine has two rollers of 50mm diameter. 6. Manufacturing Test Specimens To evaluate mechanical properties, the sheets are manufactured according to table (3), as follows: 6.1. Tensile Test Specimens Four specimens are formed according to standard (DIN 50125) specification, there dimensions are shown in figure (3). Fig.3. Tensile Specimen (DIN 50125). 7. Tests 7.1. The Rolling Process 1- Measuring grains size for specimen group before and after rolling by using optical microscope having a camera, the results are explained in table(4) and Fig.(4). This page was created using Nitro PDF trial software. To purchase, go to http://www.nitropdf.com/ http://www.nitropdf.com/ Hani Aziz Ameen Al-Khwarizmi Engineering Journal, Vol. 7, No. 2, PP 14 - 21 (2011) 17 Table 4, The Granule Size Before and After Rolling Process. Specimen Symbol A B1 B2 B3 B4 Granule size (μ) 3.68 8.61 15.02 18.32 7.45 Fig.4. Microstructure for the Sheets (A), (B1), (B2), (B3) and (B4). A B1 B2 B3 B4 This page was created using Nitro PDF trial software. To purchase, go to http://www.nitropdf.com/ http://www.nitropdf.com/ Hani Aziz Ameen Al-Khwarizmi Engineering Journal, Vol. 7, No. 2, PP 14 - 21 (2011) 18 2- Measuring rigidity for groups of table (3) treated and untreated. By Brinill hardness test method using a ball with 2.5mm diameter and 50kg load, the results explained in tables(5) and (6). Table 5, Mechanical properties of alloy after rolling without heat treatment Rolling force N Yield stress Mpa Maximum tensile stress Mpa Brinill rigidity Number of passing Thickness Mm Specimen symbol 781293.65111061.557A 1521277.6390.5100.541.4B1 2130304.342611061.275B2 2840339474.7123101.2B3 3481365.8512133121.1B4 Table 6, Mechanical properties of heat treatment alloy after rolling Rolling force N Yield stress Mpa Maximum tensile stress Mpa Brinill rigidity Number of passing Thickness Mm Specimen symbol 608253355911.557A 60829140810541.557C1 6082663739641.557C2 60831744411541.557C3 60830638210341.557C4 608295401.75104.7541.557C average Where the heat treatment alloys C1, C2, C3 and C4 are corresponding to B1, B2, B3 and B4 respectively with constant thickness, number of passing and rolling force. It can be seen the properties is differed with each case, and it properties is much better than the untreated one. 8. ANSYS Model Generation The ultimate purpose of a finite element analysis is to re-create mathematically the behavior of an actual engineering system. In other words, the analysis must be an accurate mathematical model of a physical prototype. In the broadest sense, the model comprises all the nodes, elements, material properties, real constants, boundary conditions and the other features that used to represent the physical system. In ANSYS terminology, the term model generation usually takes on the narrower meaning of generating the nodes and elements that represent the special volume and connectivity of the actual system. Thus, model generation in this study will mean the process of defining the geometric configuration of the model's nodes and elements. The program offers the following approaches to model generation: Creating a solid model and using direct generation. The method used in this research to generate a model is solid model. In solid modeling someone can be described the boundaries of the model, establish controls over the size and desired shape elements automatically, i.e. drawing the two dimensional specimen model and meshing using meshtool. Solid modeling is usually more powerful and versatile than other modeling, and is commonly the preferred method for generation models. The two Dimension model of specimen is done by plotting and meshing two dimension axisymmetric plane with elements, the sheet element is visco106 and the contact condition is used via elements contac171 for deformable body and target169 for rigid body. ANSYS software is used to analyze many case in linear and non-linear (Saeed Moveni, 1999). In this study ANSYS software is used to analyze and This page was created using Nitro PDF trial software. To purchase, go to http://www.nitropdf.com/ http://www.nitropdf.com/ Hani Aziz Ameen Al-Khwarizmi Engineering Journal, Vol. 7, No. 2, PP 14 - 21 (2011) 19 study the forming process i.e rolling process (Kawałek, 2007) and stresses distribution in the sheet with different conditions is evaluated. The model generated for nonlinear materials and non linear geometry in addition to contact case between the sheet and roller, also it is non linear process (ANSYS, 1999). Four types of elements are used as shown in Fig. (5) Fig.5. Rolling Process Model. Due to symmetry, half of the rolling process is modeled. The solid modeling is used in ANSYS to make the mesh with element type visco106 for the sheet and take into consideration the contact region which is meshed with element type target169 for rigid portion and contac171 for deformed portion. Fig.(6) shows the stress distribution in the sheet during rolling process . 9. Discussion The aluminum-copper alloy is considered one of high strength alloys therefore it is used in many engineering applications like aircraft structure; it requires heat treatment to improve its mechanical properties. The main object of rolling is to increase length and decrease thickness with keeping width constant. The solution heat treatment improves the mechanical properties; the rigidity increased 1.042 times, the tensile stress increased 1.028 times, the yield stress increased 1.662 times and the rolling force decreased 2.506 times. Fig.6. Stress Distribution in the Sheet during Rolling Process. This page was created using Nitro PDF trial software. To purchase, go to http://www.nitropdf.com/ http://www.nitropdf.com/ Hani Aziz Ameen Al-Khwarizmi Engineering Journal, Vol. 7, No. 2, PP 14 - 21 (2011) 20 Results are taken from this research are; rigidity and tensile strength, it is found that the solution heat treatment improves the mechanical properties for (2024-T3) alloy. By decreasing number of passing between rollers, keeping thickness and a free from strain hardening. It is found that force needed for rolling untreated sheets is greater than force needed for solution heat treated because of strain hardening. The stresses’ result in sheet B4 is bigger than that of sheet B3 , B2 , B1 respectively, due to the factor (ho-hi) is bigger in spite of the yield stress is bigger, while the stresses in sheets C1,C2,C3, and C4 is not vary significantly due to constant thickness. 10. Conclusions It can be concluded the following: 1. Mechanical properties for the alloy without heat treatment and rolling were good because of strain hardening. 2. Mechanical properties for the alloy after heat treatment and rolling is improved 1.5% but with less force and stress compared with untreated. 3. The availability of using ANSYS program to make the rolling process and to show the stresses distribution in the alloy during rolling process. Notation L the length of contact line between roller and sheet (mm). R radius of roller (mm). ho the thickness before rolling (mm). hi is thickness after rolling (mm). Pr roller pressure (N/mm2). QP multiplication factor Fr roller force (friction ) (N). w sheet width (mm). T roller torque (T.m). V linear velocity (m/sec). R roller radius (mm). Greek letters ρ density (Kg/m3). σ stress (N/mm2). σtm flow stress (N/mm 2). ω angular velocity (rad/sec). 11. References [1] Wang Feng" Microstructure And Mechanical Properties Of Spray-Deposited Al–Zn–Mg– Cu Alloy Processed Through Hot Rolling And Heat Treatment", 2009. [2] Shahani A. R., Nodamaie S.A. and Salehinia I. “Parametric Study of Hot Rolling Process by the Finite Element Method”, Transaction B: Mechanical Engineering Vol. 16, No. 2, pp. 130{139, Sharif University of Technology, April 2009. [3] P. Chandramohan, K. Manikanda Subramanian, P. Chandrasekar “ Rolling Process With Ohsas And Texture Formation– A Review”, Journal Of Engineering Science And Technology, Vol. 4, No. 1, 1–19, School Of Engineering, Taylor’s University College,2009 [4] Johnson W. and Needham G. “Further Experiments in Asymmetrical Rolling”, Int. J. Mech. Sci., Vol. 8, 1982. [5] Johnson W. and Mellor P.B. “Engineering Plasticity”, Elshorwood Limited, New York, 1973. [6] Nagpal G.R. "Metal forming processes", first edition, 1998. [7] Kawałek A. “The analysis of the asymmetric plate rolling process” Journal of Achievements in Materials and Manufacturing Engineering, Vol.23, issue 2, August, 2007. [8] Saeed Moveni, “Finite element analysis, theory and application with ANSYS”. 1999. [9] ANSYS – help, “Structural Manual”, Ansys, Inc., 1999. This page was created using Nitro PDF trial software. To purchase, go to http://www.nitropdf.com/ http://www.nitropdf.com/ 21 ، صفحة2، العدد 7مجلة الخوارزمي الھندسیة المجلد ھاني عزیز أمین - 14 )2011( 21 تأثیر المعاملة الحراریة المحلولیة على الخواص المیكانیكیة لسبیكة باستعمال عملیة الدرفلة (T3-2024)نحاس -ألمنیوم *** خیریة سلمان حسن ** أسماء حسن أسماعیل * ھاني عزیز أمین بغداد/ الكلیة التقنیة /ب والعددم ھندسة القوالقس * haniazizameen@yahoo.com : البرید االلكتروني جامعة بغداد /كلیة الھندسة/ ھندسة المیكانیكیةقسم ال ** asma.sawaf@yahoo.com : البرید االلكتروني بغداد/ التكنولوجیامعھد /يالقسم المیكانیك *** almaden20002000@yahoo.com : البرید االلكتروني !!!!!!!!!!!!! الخالصة ة T3-2024نحاس -دراسة تأثیر المعاملة الحراریة المحلولیة على الخواص المیكانیكیة لسبیكة ألمنیوم ة الدرفل الل عملی ة . من خ راء معامل م إج ث ت حی دن (C°480)حراریة تضمنت تسخین صفائح من ھذه السبیكة إلى درجة حرارة كیل الل ة التش راء عملی م إج دھا ت اء بع ریع بالم د الس ة (ثم التبری ى ) بالدرفل عل ة ا م دراس دھا ت ھر بع كیل ھذه الصفائح المقساة ثم إجراء عملیة تعتیق طبیعي لمدة ش ة التش راء عملی م إج ث ت الدة حی د وص ة ش ن مقاوم ة م واص المیكانیكی لخ ل دون تعام دن ب ائج للمع ة النت ددة ومقارن كیل متع ب تش ل وبنس ین درافی فائح ب ر الص الل تمری ن خ ة م ة الدرفل امج . بواسطة عملی تخدام برن م اس ANSYSت ة ة الدرفل ي عملی ادات ف ع االجھ ة توزی ین أن . لدراس د تب ولق الي الخ الد االنفع مى باالص ا یس بب م ل بس راري افض ل ح دون تعام بیكة ب ة للس اص المیكانیكی . والخواص المیكانیكیة للسبیكة بعد المعاملة الحراریة والدرفلة تحسنت ایضًا ولكن بجھد وقوى اقل مقارنة بتلك التي اجریت بدون معاملة This page was created using Nitro PDF trial software. To purchase, go to http://www.nitropdf.com/ http://www.nitropdf.com/