(Microsoft Word - \307\315\343\317 \332\343\355\31782- 88) Al-Khwarizmi Engineering Journal Al-Khwarizmi Engineering Journal, Vol. 15, No. 1, March, (2019) P.P. 82- 88 Study of Fatigue Fractography of Mild Steel Used in Automotive Industry Ahmed Ameed Zainulabdeen Department of Materials Engineering/ University of Technology Email: ahmed_ameed@yahoo.com (Received 27 February 2018; accepted 1 July 2018) https://doi.org/10.22153/kej.2019.07.003 Abstract Fatigue failure is almost considered as the predominant problem affecting automotive parts under dynamic loading condition. Thus, more understanding of crack behavior during fatigue can strongly help in finding the proper mechanism to avoid the final fracture and extent the service life of components. The main goal of this paper is to study the fracture behavior of low carbon steel which is used mostly in automotive industry. For this purpose, the fractography of samples subjected to high and low stress levels in fatigue test then was evaluated and analyzed. Hardness and tensile tests were carried out to determine the properties of used steel. Also, the samples were characterized by microstructure test and XRD analysis to examine the constitute phases. The fatigue test (S-N curve) was done at stress ratio (R= -1), and the fracture examination was perform using Scanning Electron Microscope (SEM). The results of microstructure and XRD analysis were indicating that the Ferrite and a little amount of pearlite are the dominant phases of this steel. Whereas, the fractography observations reveal that the void coalescence ductile fracture is the main failure mode in samples with high stress level, while the ductile fracture (void coalescence) with Transgranular Cleavage fracture was noticed in low stress fatigue mode for this alloy. Keywords: Automotive, fatigue, fracture, mild steel. 1. Introduction Automotive vehicles have become an important part of our everyday lives. Therefore, it is necessary to continually attempt to enhance their service life and design. Nowadays, with the fast progress in advanced technologies, the automotive industries become under grown pressure to produce vehicles which are more life service, safe and with best crash performance [1, 2]. Mild Steel have wide usage in automotive industry as a shafts, axles, gears, suspension and chassis parts. However, a lot of these parts are very liable to fatigue failure, which happened without any prior warning, because of the elevation levels of cyclic loading that encounter normal use [2, 3]. Therefore, it is critical to understand the loading mechanisms and evaluation the fatigue behavior of the parts under dynamic loading conditions to ensure extend their service life and make it more safe. In the last decades there has been a growing interest in studying the mechanism of fatigue failure at different environments. So, many fatigue fractography investigation in last decade were made, Chang-Yeol Jeong [4] showed that fatigue life and the fatigue strength increased with higher yield and tensile strengths. The fatigue fracture behavior of AISI 1018 mild steel which expose to rotating bending- torsional fatigue were studied by M.W. Dewan et al [5]. They noticed that the small size dimples were due to high tensile stress. The effect of microstructure and short cracks in three groups of low carbon steel specimen subjected to tension-tension, rotating bending and pure bending loading on fatigue strength were investigated by Donka et al [6]. They noticed that the tension- tension fatigue specimen possesses the smallest crack growth rate due to lesser applied loading than Ahmed Ameed Zainulabdeen Al-Khwarizmi Engineering Journal, Vol. 15, No. 1, P.P. 82- 88 (2019) 83 other groups, while shorter fatigue life span were noticed for rotating bending specimen groups due to elevation fatigue load. This work presents a systematic study of the mechanisms of fatigue damage in terms of initiation and propagation of fatigue cracks to failure of low carbon steel samples under low and high stress levels. The main goal is to provide greater insights into the alloy design of this steel and their subsequent engineering. 2. Experimental work A. The Materials The used steel in this study was (St 37) according to DIN standard which supplied as rods of 13 mm diameter and 1m long which were cut later to 150 mm long. The chemical composition was performed using Oxford X-Met 3000TX spectroscopy and the chemical compositions as shown in Table (1). Table 1, chemical composition of steel Element C Mn Si S P Fe wt.% 0.17 1.4 0.3 0.045 0.045 Rem. B. Mechanical Tests A Microhardness of a sample is tested by digital micro hardness tester (H.V.) under load of (9.8) N and dwell time of (15) second. A cylindrical shape specimen with (Ø 10mm× 6 mm) was used. The taken reading was an average of three reading. The tensile test of specimen was carried out using WP 300 universal material tester device. The specimen was prepared according to (ASTM E8) standard. A roughness test was performed using stylus probe type device to ensure the constancy of a tested surface subjected to fatigue. The average value of all samples were approximately Ra =0.5 (µ m). Fatigue tests were done using Gunt WP-140 fatigue testing machine with rotating bending load type and stress ratio (R= -1) at laboratory temperature. Cycles of 1×106 cycles were considering as a run out test. An average value of 3 specimens was adopted. Also Stress-Number of cycle to fail (S-N curve) was plotted and fatigue limit was concluded. A fatigue specimen dimensions is shown as in Fig (1). C. Non Destructive Inspections Microstructure examination were performed using BEL type optical microscope with 5 Mega pixel accompanied camera. Wet grinding was carried out using different grades of emery papers (320 up to 1200) followed with diamond paste 0.2 μm and its lubricant for polishing to get a high surface finish. Finally, the specimen was etched using Nital solution (2% HNO3 and 98% Ethanol). X-ray Diffraction analysis was used to ensure the contestant of ferrite and little amount of pearlite for the used alloy. The fractured specimens from fatigue tests have been examined using scanning electron microscope TESCAN VEGA3 LMU. This inspection was done to fractured specimens subjected to low and high stresses with different magnifications. All the tests and measurements in this research were carried out at room temperature. Fig 1. Fatigue test specimen dimensions (mm) . 3. Results and Discussion A. Microstructure Examination The microstructure of used steel is illustrated in Fig (2) with two magnifications. It is clear from Fig that the microstructure consists of pearlite regions (dark area) uniformly distributed with irregular shapes and imbedded in the matrix of ferrite (bright area). The percentage of pearlite content was about 17% (according to Image J software). More information can be concluded using X-ray Diffraction analysis which revealed the peaks of ferrite (pure iron) which it is the matrix of the used alloy as shown in Fig (3). Ahmed Ameed Zainulabdeen Al-Khwarizmi Engineering Journal, Vol. 15, No. 1, P.P. 82- 88 (2019) 84 Fig. 2. Pictures show the microstructure of steel sample. Fig. 3. XRD analysis of Sample. B. Tensile and Hardness Results Table (2) and Fig (4) present the hardness and tensile properties of used steel. A high ductility level can be observed due to the high content of ferrite which is very suitable for most automotive applications. These results have good agreement with previous literatures [7]. Table 2, Hardness and Tensile tests results State Hardness (HV), (Kg/mm) ∆L (%) Yield strength (σy),(MPa) Tensile strength (σu),(MPa) As received 182 29 325 (approx.) 413 Fig. 4. Stress-strain of As-received steel material (St 37). Ahmed Ameed Zainulabdeen Al-Khwarizmi Engineering Journal, Vol. 15, No. 1, P.P. 82- 88 (2019) 85 C. Fatigue Behavior Before fatigue test was carried out a roughness measurement have been made to ensure the proper surface roughness for fatigue samples. Rotating bending fatigue testing machine was used to determine Fatigue limit of used steel as a stress- number of cycle to failure (S-N) curve. Fig (5) and Table (3) shows the results of this test, which was 160 MPa, and this is deal with previous literatures [8]. Table 3, Stress-Number of cycles data for as received samples Sample no. Stress (MPa) Number of cycle 1 400 11600 2 380 19480 3 350 27260 4 300 46720 5 260 60080 6 210 91200 7 200 210300 8 180 480500 9 160 1e6 (not fail) Fig. 5. S-N curve for steel (St 37) in as received condition. Particular attention is paid to the fractography study, which was done using Scanning Electron Microscope, for samples at high and low stress levels. Fig (6) presents section of fracture surface for specimen at high stress level (380 MPa). For more clarify the failure zones marked with number from 1 to 4. It can be shown from Fig (7) that the crack initiate from the surface and propagate quickly with small extension. At the same time, the final catastrophic failure zone was wider comparing to that of crack progress zone. This is attributed to high levels of load in this region. Fig. 6. Fatigue fractography for (St 37) in as received condition at high stress. Fig .7. Fatigue fractography for sample in as received condition at high stress (cont.). Fig (8) represents fracture surface for specimen at low stress levels. Fig reveal different features than previous one (high stress levels) due to difference in loading levels. It’s clear that there is wider crack propagation zone because the crack Cycles to fail S tr e ss ( M P a ) Ahmed Ameed Zainulabdeen Al-Khwarizmi Engineering Journal, Vol. 15, No. 1, P.P. 82- 88 (2019) 86 has more time to advance before failure. More than initiation spot was noticed and the final catastrophic failure zone was smaller. Also river marks were noticed in the propagation zone which refer to crack advancing direction toward final fracture. In addition to, by viewing the fractography in more details and reviewing the previous literature [9], it can be concluding that this configuration of fracture topography indicates the low stress with high stress concentration conditions. The failure zones marked with number from 1 to 3 as shown in Fig (8). Fig .8. Fatigue fractography for sample in as received condition at low stress. For more analysis, failure zones divided in Fig (9) into three areas and marked with number from 1 to 3. first zone (1) shows the crack initiation zone with many river marks, while zone (2) shows the evolution of micro cracks with circumferential direction around the final rupture. Zone (3a) indicates the final fracture with formation of voids as a part of ductile fracture phenomena. Zone (3b) represents a magnifying zone of the same zone (3a) which reveal crack facet which is the main feature of Transgranular cleavage fracture. This type of failure (Cleavage fracture) is familiar for BCC structures especially steels [10]. Also it was noticed that the final fracture is off-center, i.e. shifted toward the opposite side of final overload, this result is in a good agreement with Shipley et al [11]. Fig. 9. Fatigue fractography for sample in as received condition at low stress. 4. Conclusions From the obtained results, it is possible to conclude the following: 1. The Void coalescence ductile fracture is the main failure mode in high stress level. 2. The dominant failure mode is the general fatigue failure mode, which started by crack initiation and propagation, also ductile fracture (void coalescence) with Transgranular Cleavage fracture was noticed in low stress fatigue mode for this alloy. 3. This alloy is seeming to be encouraged to use in automobile applications subjected to moderate fatigue loading due to good fatigue limit and elongation. 5. References [1] Nacy, Somer M. "Effect of Heat Treatment on Fatigue Behavior of (A193-51T-B7) Alloy Steel.", Proceedings of the World Congress on Engineering, pp1247-1250, Vol II, 2007, London, U.K. Ahmed Ameed Zainulabdeen Al-Khwarizmi Engineering Journal, Vol. 15, No. 1, P.P. 82- 88 (2019) 87 [2] Shrama, Kadhum. “Fatigue of welded high strength steels for automotive chassis and suspension applications”, PhD. Thesis, School of Engineering, Cardiff University, 2016. [3] B. Claude, “Fatigue of materials and structures”, John Wiley & Sons, 2013. [4] J. C. Yeol. "High-Cycle Fatigue Properties of Automobile Cold-Rolled Steel Sheet with Stress Variation", Materials Transactions vol.54, No.10, pp.2037-2043, (2013). [5] M. W. Dewan, G. González, and M. A. Wahab. "Effects of Rotating-Bending and Torsional Fatigue Loads on Gas Tungsten Arc (GTA) Welded AISI 1018 Low Carbon Steel Joints." ASME 2015 International Manufacturing Science and Engineering Conference. American Society of Mechanical Engineers, 2015. [6] D. Angelova, R. Yordanova, and S. Yankova. "Fatigue crack development in a low-carbon steel. Microstructure influe- ence Modelling." Procedia Structural Integrity Vol.2 pp. 2726-2733, (2016). [7] ASM Handbook, Volume 1, Properties and Selection: Irons, steels and high performance alloys, ASM International, USA, 1990. [8] A. A. abid and A. F. Jawad,” Effect of Martensite Volume Fraction On the Microstructure and Mechanical Properties of Low Carbon Dual Phase Steel”, Applied Research Journal, Vol.2, No.6, pp.266-274, June, 2016. [9] N.W. Sachs, "Understanding the surface features of fatigue fractures: how they describe the failure cause and the failure history." Journal of Failure Analysis and Prevention Vol.5, No.2, pp. 11-15, (2005). [10] S. K. Akay, M. Yazici, A. Bayram and A. Avinc, "Fatigue life behaviour of the dual- phase low carbon steel sheets", Journal of materials processing technology, Vol. 209, No.7, pp. 3358-3365, (2009). [11] R.J. Shipley and W.T. Becker, ASM Handbook, Vol.11,” Failure Analysis and Prevention. ASM International, 2002. )2019( 82- 88، صفحة 1د، العد15دجلة الخوارزمي الهندسية المجلم احمد عميد زين 88 دراسة مقطع كسر الكالل للفوالذ المطاوع المستخدم في صناعة السيارات احمد عميد زين العابدين الجامعة التكنولوجية /قسم هندسة المواد ahmed_ameed@yahoo.com :البريد االلكتروني الخالصة الشائعة المؤثرة على أجزاء السيارات المعرضة ألحمال دورانية. لهذا فان فهم سلوك الشقوق اثناء حدوث الكالل تفشل الكالل من أخطر المشاكال ديع لكربون والمستخدم تجنب حدوث الفشل النهائي للجزء اثناء الخدمة واطالة عمره. ان الهدف األساس للبحث هو دراسة سلوك الكسر للفوالذ الواطئ ا علىيساعد . كما تم اجراء اختبارات الصالدة هاوتحليل يم األجزاءوفي صناعة السيارات. لهذا السبب، تم دراسة مقطع الكسر للكالل عند احمال كالل واطئة وعالية لتق د االشعة السينية لتفحص االطوار والمكونات دراسة البنية المجهرية ودراسة حيو عن طريقوالشد لتحديد خواص الفوالذ المستخدم. كذلك، تم توصيف المادة . (SEM)، وتم دراسة مقطع الكسر باستخدام المجهر االلكتروني الماسح (R=-1)عدد الدورات) تم اجراءه عند نسبة اجهاد -للسبيكة. ان اختبار الكالل (االجهاد ن الفوالذ هو الفرايت مع نسبة قليلة من البيراليت، بينما اظهر مقطع الكسر تكون اشارت نتائج الفحص المجهرية واالشعة السينية بان الطور السائد لهذا النوع م قسامي تكون الكسر كسر مطيلي بالتحام الفجوات حيث ان هذا هو األسلوب عند اجهادات عالية، بينما أظهرت النتائج عند اجهادات كالل واطئة تكون الكسر االن السبيكة.المطيلي الناتج عن التحام الفجوات لهذه