Vol49_2_2006 625 ANNALS OF GEOPHYSICS, VOL. 49, N. 2/3, April/June 2006 Key words deep-sea borehole observatory – broad- band seismometer – seismic noise level – long-term observation 1. Introduction Tomographic studies using earthquake waves propagating through the Earth’s interior have rev- olutionized our understanding of mantle structure and dynamics. One of the most important limita- tions on existing tomographic analyses and im- ages of the Earth’s interior is the uneven distribu- tion of seismic stations, specifically the lack of stations situated on oceanic crust or in oceanic basins. The scientific importance of establishing long-term geophysical stations at deep ocean sites has been acknowledged by the Earth science communities and is detailed in various reports (e.g., ION/ODP International Workshop, 1995). The objective of tomographic studies is to under- stand the structure and dynamics of the tectonic system from a regional to global scale by imag- ing the Earth’s interior with seismic waves. Un- fortunately, few seismometers are sited on the 71% of the Earth’s surface covered by oceans. Deep-sea borehole seismological observatories in the Western Pacific: temporal variation of seismic noise level and event detection Masanao Shinohara (1), Ei’ichiro Araki (2), Toshihiko Kanazawa (1), Kiyoshi Suyehiro (2), Masashi Mochizuki (3), Tomoaki Yamada (1), Kazuo Nakahigashi (1), Yuka Kaiho (2) and Yoshio Fukao (1) (2) (1) Earthquake Research Institute, University of Tokyo, Japan (2) Japan Agency for Marine-Earth Science and Technology, Yokosuka, Japan (3) Institute of Industrial Science, University of Tokyo, Japan Abstract Seismological networks provide critical data for better understanding the dynamics of the Earth; however, a great limitation on existing networks is the uneven distribution of stations. In order to achieve a more uniform distri- bution of seismic stations, observatories must be constructed in marine areas. The best configuration for ocean- ic seismic observatories is thought to be placement of seismometers in deep boreholes. Two deep-sea borehole seismological observatories (WP-1 and WP-2) were constructed in the Western Pacific and form the initial in- stallations of a 1000 km span network. At present, seismic records of more than 400 total days were retrieved from both the WP-1 and WP-2. Long-term variations in broadband seismic noise spectra (3 mHz-10 Hz) in the Western Pacific were revealed from these records, and the data showed that ambient seismic noise levels in bore- hole observatories are comparable to those of the quietest land seismic stations. In addition, there is little tem- poral variation of noise levels in periods greater than 10 s. Due to this low seismic noise environment, many tele- seismic events with magnitudes greater than 5 were recorded. It is confirmed that seismic observation in deep- sea borehole gives the best environment for earthquake observation in marine areas. Mailing address: Dr. Masanao Shinohara, Earthquake Research Institute, University of Tokyo, Tokyo 113-0032, Japan; e-mail: mshino@eri.u-tokyo.ac.jp 626 Masanao Shinohara et al. The asymmetry and non-uniformity of the seis- mic station distribution makes high-resolution imaging of some parts of the mantle nearly im- possible. Many ocean bottom geophysical sen- sors, whose locations have been carefully select- ed to optimize imaging, are needed around the world to attain the goals of the various interna- tional geoscience programs. The Japanese Ocean Hemisphere Network Project (OHP: 1996-2002, http://eri-ndc.eri.utokyo.ac.jp/en/ohp/index.html) selected the Western Pacific area for installation of ocean-bottom sensors because it is ideal for addressing problems related to plate subduction. Based on the results of previous studies using borehole seismometers on the seafloor, it is be- coming clear that emplacement of seismometers into the igneous crust using boreholes can pro- vide low noise environments (Kanazawa et al., 1992; Suyehiro et al., 1992; Montagner et al., 1994; Beauduin and Montagner, 1996; Roma- nowicz et al., 1998; Stephen et al., 1999; Collins et al., 2001; Araki et al., 2004). However there are no observational records covering a span of more than a half year in any deep-sea borehole observatory. The OHP installed four borehole geophysical stations at three sites covering a pe- riod from 1999 to 2001 (fig. 1). In 1999, two borehole stations (JT-1 and JT-2) were installed during ODP Leg 186 (Sacks et al., 2000) and are located immediately above the inter-plate earth- quake generation zone on the landward side of the Japan Trench. The JT-1 and JT-2 stations were installed approximately 50 km apart and have two broadband seismometers, a strainmeter and a tiltmeter for each station. In August 2000, during ODP Leg 191, the borehole seismological obser- vatory WP-2 was successfully installed at ODP Site 1179 in the northwestern Pacific Basin (Kanazawa et al., 2001). Borehole seismic obser- vatory WP-1 was installed in the west Philippine Basin during ODP Leg 195 in April 2001 (Salis- bury et al., 2002). The WP-1 and WP-2 observa- tories each have two identical broadband seis- mometers. Together, these observatories can cov- er a large expanse of the northwestern Pacific in areas that comprise major gaps in the coverage provided by pre-existing global seismological ob- servatories. At present, the data from these four borehole observatories are retrieved by ROV vis- its at an interval of about 0.5-1.5 year (Suyehiro et al., 2002). Araki et al. (2004) have already re- ported on the JT-1 and JT-2 observatories and the characteristics of the geophysical data obtained from the JT-1 Observatory. In this paper, we de- scribe the characteristics, layout, and system pa- rameters of the WP-1 and WP-2 seismological observatories, and the characteristics of the seis- mic data retrieved from them, specifically the am- bient seismic noise levels, temporal noise varia- tions, and performance of the observatories. 2. Deep-sea borehole seismological observatories WP-1 and WP-2 2.1. System The WP-1 and WP-2 seismic observatories were designed to work for more than five years as stand-alone systems. Because the characteris- tics of the WP-1 and WP-2 observatories have al- ready been described in detail (Kanazawa et al., 2001; Salisbury et al., 2002), we explain their Fig. 1. Location map of seismic station coverage in the northwest Pacific. Small black and light gray cir- cles indicate land seismic stations, dark gray circles are seafloor borehole observatories. The WP-1 and WP-2 observatories were installed in August 2000 and April 2001, respectively. Note that a few bore- hole stations can effectively complement and expand the existing network. 627 Deep-sea borehole seismological observatories in the Western Pacific F ig . 2. S ch em at ic b lo ck d ia gr am o f th e W P -1 s ei sm ic o bs er va to ry . T w o id en ti ca l se ns or s ba ck u p ea ch o th er . T he s ig na ls f ro m t he s en so r ar e di gi - ti ze d at t he b ot to m o f th e bo re ho le a nd a re r ec or de d to h ar d di sk s on t he s ea fl oo r. F ig . 3. S ch em at ic b lo ck d ia gr am o f th e W P -2 s ei sm ol og ic al o bs er va to ry . T he p ow er f or t he e nt ir e sy st em i s su pp li ed f ro m t he S ea W at er B at te ry an d ba ck up l it hi um b at te ri es . T he s en so rs w er e gr ou te d at d ep th s of 4 60 m b el ow t he s ea fl oo r in b as al ti c ba se m en t. 2 3 628 Masanao Shinohara et al. design and layout briefly here. Both systems are basically identical except for the power supply (figs. 2 and 3). There is a retired co-axial trans- oceanic telephone cable near the WP-1 Observa- tory that will be utilized in the future for data re- covery and power supply. Presently, however, both observatories work as stand-alone systems with their own batteries and recorders. Two broadband seismometers (Guralp CMG-1TD) were placed near the bottom of the borehole in igneous basement. The seismometers were em- placed in the borehole permanently; they were cemented into the hole in order to assure good coupling with the surrounding crust. The signals are digitized in the sensor packages and sent in digital form to the seafloor data-recording pack- ages. The seafloor package serves to combine the digital data from the two seismometers to a single serial data stream. The data are stored to a data recorder in a digital format via a RS-232C link. Because the recorder unit can be recovered by an ROV, the recorder has been improved in concert with the improved electronics packages developed over the past few years. At present, the recorder has four 30 Gb SCSI hard disks equivalent to more than 6 channels of one-year continuous data of 24 bit dynamic range at a 100 Hz sampling rate. The recorder unit also pro- vides a communication link to the borehole sys- tem. The status of the observatory can be check- ed via an «ROV interface» that enables RS-232C communication between the recorder and the ROV during an ROV visit. The major difference between the WP-1 Ob- servatory and the WP-2 Observatory is in the electric power supply system. For the WP-1 Ob- servatory, power is supplied from a Lithium Bat- tery System (LBS) consisting of two units, each comprising sixteen lithium cells. Eight of these cells are connected serially and two series are connected in parallel, and each unit has a capaci- ty of 2600 Ah. Each battery unit is contained in two titanium spheres with a diameter of 65 cm. The battery system should, based on system spec- ifications, provide power to the observatory for ∼2.5 years. Electric power for the WP-2 Observa- tory is supplied from a Sea Water Battery (SWB) (Hasvold et al., 1997), which can supply up to ∼24 W with more than 400 kWh capacity. The power is derived from electrolytic dissolution of a magnesium anode in seawater, and power gen- eration is dependent on seawater conditions (salinity, temperature). Because the performance of the SWB depends on the condition of seawa- ter, additional lithium batteries are used as a backup power supply. All the seafloor instru- ments and the magnesium anode of the SWB are designed to be replaceable by ROV. 2.2. Installation Installation of the seismometer systems for the WP-1 and WP-2 observatories was performed in April, 2001 and August, 2000, respectively. Each of the boreholes was drilled through sedi- mentary rock into basaltic oceanic basement, and the seismometers were installed in the basaltic sections of the boreholes. The seismometers were supported on 4.5m diameter casing pipe hanging on the base of a permanent reentry cone mounted on the mouth of the borehole at the seafloor (fig. 4). This pipe provided a basis for instrument in- sertion and a conduit for cement pumping for an- choring of the seismometers. Grouting cement was pumped through the casing pipe, and then up around the seismometers. The seismometers were grouted at depths of 561 m below seafloor (mbsf) and 460 mbsf in basement rock 19 m and 15 m above the bottom of the boreholes for WP- 1 and WP-2, respectively. After cementing, the drill pipe from the ship was decoupled and with- drawn leaving the casing pipe in the hole. The power and data cables attached to the seismome- ter and leading to the data recording and power supply were protected from wear and chafing by being anchored to the casing pipe and are protect- ed from wall contact by centralizers. The cable it- self is designed to be almost neutrally buoyant in seawater, further minimizing long term stress on the cables. After cementing of the seismometers was complete, assembly of the battery/recorder unit was accomplished onboard, and the battery/rec- order unit was lowered through the moon pool on drilling deck of the Joides Resolution and mounted on the reentry cone, after which time the batteryrecorder unit was released from the ship via acoustic signal and the drill string was recovered. 629 Deep-sea borehole seismological observatories in the Western Pacific 2.3. System activation and data recovery In March 2002, KAIKO, a full-ocean depth ROV belonging to the Japan Marine Science and Technology Center (JAMSTEC), visited the WP- 1 site to activate the observatory, and long-term observation was started using the first LBS unit. Both the seismometers at the WP-1 were con- Fig. 4. Installation procedure of the deep-sea borehole broadband seismic observatory. After completion of drilling, the sensor string assembly was lowered into the hole. Because a TV camera was needed for the re-entry of the sen- sor string assembly, the sensors could not be connected to the batteries and data recorder on the seafloor. The cement was displaced down hole for fixing of the sensors. The battery/recorder unit was lowered along the drill string and was released by an acoustic command. After installation, an ROV was used to activate the system. 630 Masanao Shinohara et al. firmed to work properly from the R/V Kairei via an RS-232C link, one seismometer was deactivat- ed to decrease power consumption. In October 2002, the KAIKO re-visited the WP-1 site and we obtained ∼6 months of continuous data (Mar 26- October 6, 2002) (fig. 5). The KAIKO visited the WP-1 site again in May 2003 and ∼ 7 months of continuous data (October 7, 2002-May 7, 2003) were retrieved. During the third visit, the KAIKO changed an electric connection and the second LBS unit was put on line to supply the power to the system. At present, seismic records of 408 days in total have been obtained from the WP-1 Observatory. The WP-2 Observatory was activated in Oc- tober 2000 using the ROV KAIKO. Since the per- formance of Sea Water Batteries (SWB) depends on the environment around the deployed position, there was a possibility that SWB could not gener- ate enough power for the whole system. There- fore, we decided to operate WP-2 using lithium batteries during the first observation period as the preliminary observation and had developed a lithium battery system, which supplies the power to the system. The lithium battery system consists of five lithium batteries with a total capacity of 1300 AH. Only one seismometer was activated in order to minimize power consumption, similar to the case for WP-1. In August 2001, the KAIKO re-visited the WP-2 site. Approximately three- months of continuous data (October 29, 2000- January 21, 2001) were recovered. During the second visit, it was confirmed that the SWB sys- tem continued working properly, and long-term observation using both the SWB and backup Table I. Summary of observation period of the WP- 1 and WP-2 observatories. WP-1 Observatory WP-2 Observatory Installation ODP Leg 195 ODP Leg 191 April, 2001 August, 2000 Activation March 26, 2002 October 29, 2000 Data periods March 26, 2002- October 29, 2000- October 6, 2002 January 21, 2001 October 7, 2002- August 3, 2001- May 7, 2003 June 30, 2002 Total 408 days 417 days Status In operation In operation Fig. 5. An ROV view of the WP-1 station after the maintenance of the system (October 6, 2002). The power is supplied from lithium batteries in the titani- um spheres (Lithium Battery System unit). Top of the battery frame is also used as an ROV landing pad. The data recorder package can be seen on top of the battery/recorder unit. Fig. 6. Installation of the titanium sphere contain- ing the data recorder and the lithium batteries as backup at the top of the platform for long-term ob- servation for the WP-2 station (August 5, 2001). The power is mainly supplied from the Sea Water Battery system. The SWB system has four SWB1200 cells. The cell is a magnesium and oxygen battery based on a magnesium anode that uses seawater as the elec- trolyte. When voltage from the SWB is dropped, the lithium batteries in the sphere supply backup power. 631 Deep-sea borehole seismological observatories in the Western Pacific lithium battery system was initiated (fig. 6). When the SWB generates enough electric power for the system, the system is supplied the power from the SWB. If the SWB cannot generate the power, the backup lithium battery system sup- plies the power to the system. The backup lithium battery system can supplies the power for approx- imately three months. The KAIKO visited the WP-2 site again in June 2002 and ∼11 months of continuous data (August 3, 2001-July 29, 2002) were retrieved for the second observation period. The KAIKO also recovered the monitoring data for the SWB system, confirming that the SWB system worked continuously for almost one year. The operation details of the WP-1 and WP-2 ob- servatories until the end of 2003 are summarized in table I. 3. Seismic records from the WP-1 and WP-2 observatories 3.1. Background seismic noises in deep-sea boreholes The seismic data from the WP-1 and WP-2 seismological observatories enable the study of broadband seismic noise in the frequency range from 3 mHz to 50 Hz in the northwestern Pacific over a period covering more than one year of con- tinuous recording. Temporal changes in ambient seismic noise within deep-sea borehole can be analyzed in depth using this data. Figure 7a-d shows the noise level as a func- tion of time and period for vertical and horizontal components of the WP-1 and the WP-2 observa- Fig. 7a. Running spectra of the records from the deep-sea borehole observatories. Each spectrum is calculated with a moving time window for a total of one hour record. Here the spectra are for the vertical component of the WP-1 Observatory. There is little change in noise levels above 10 s period. Many earthquakes are visible on the running spectra in periods greater than 10 s. Small temporal variations (maximum fluctuation is 10 dB) of noise levels for periods around a few seconds are seen. 632 Masanao Shinohara et al. Fig. 7b,c. Running spectra of the records from the deep-sea borehole observatories. Each spectrum is calculated with a moving time window for a total of one hour record. b) Spectra for the horizontal component of WP-1. A to- tal of 408 days of continuous data were obtained form the WP-1 Observatory. c) Spectra for the vertical component of the WP-2 Observatory. A total of 417 days of continuous data were retrieved from WP-2. There is little change in noise levels above 10 s period. Many earthquakes are visible on the running spectra in periods greater than 10 s. Small temporal variations (maximum fluctuation is 10 dB) of noise levels for periods around a few seconds are seen. b c 633 Deep-sea borehole seismological observatories in the Western Pacific tories. Each spectrum is calculated with a time window of about four minutes shifted every two minutes and is averaged for a total of one hour record. All spectra for one hour are plotted as a function of time. The major advantage of bore- hole observatories is that there are little or no temporal changes in noise levels for periods longer than 10 s. Vertical high-level bars in the running spectra indicate earthquakes. In contrast, small temporal variations (maximum fluctuations of 10 dB) in noise levels for periods around a few seconds are seen. All power spectrum densities calculated using the moving window for every one hour are plot- ted as a function of periods (fig. 8a-d), and the spectra are grouped by seasons. It is confirmed from fig. 8a-d that the noise levels for both verti- cal and horizontal components of the both the WP-1 and WP-2 observatories for periods of greater than 10 s are stable year round. It is found that the noise levels in the vertical component at the WP-1 reach −180 db for time-periods be- tween 10 s and 100 s. On the other hand, small temporal changes of noise levels in periods around a few seconds are seen. The WP-1 Obser- vatory recorded relatively large noise levels in summer and fall. The vertical component of the WP-2 Observatory has minimum noise levels about −145 db. The noise levels in the horizontal component in the WP-2 seismometer are −160 db for time-periods between 10 s and 100 s and are lower than that of the vertical component. The records from the WP-2 Observatory reveal high noise levels in a period range of a few seconds during winter. For both the vertical and the hori- zontal components of both the observatories, the noise levels are close to the Low Noise Model (Peterson, 1993) near the 10 s period. In general, the peak in noise spectrum near a period of 100 s in measurements taken at the seafloor or in a shal- low-sea borehole is due to deformation of the seafloor by ocean gravity waves (Webb, 1998). Fig. 7d. Running spectra of the records from the deep-sea borehole observatories. Each spectrum is calculated with a moving time window for a total of one hour record. Here the spectra are for the horizontal component of WP-2. A total of 417 days of continuous data were retrieved from WP-2. There is little change in noise levels above 10 s period. Many earthquakes are visible on the running spectra in periods greater than 10 s. Small tem- poral variations (maximum fluctuation is 10 dB) of noise levels for periods around a few seconds are seen. 634 Masanao Shinohara et al. Fig. 8a,b. Power spectra of the deep-sea borehole seismic observatories. Power spectra estimated using one- hour records for the all observation period are plotted. HNM and LNM indicate the high noise model and the low noise model by Peterson (1993), respectively. The power spectra are grouped by seasons: a) for vertical com- ponent of WP-1; b) for horizontal component of WP-1. The horizontal component records of the WP-1 Obser- vatory have larger noises in periods longer than 20 s. The records of the WP-1 have larger noise levels near a few seconds period in summer. Araki et al. (2004) reported that installation of a seismometer in the basement rocks minimize the effect of the ocean gravity wave. Because all the seismometers of the WP-1 and WP-2 observato- ries were installed into basaltic basement, there is no peak due to the ocean gravity waves. The horizontal component records of the WP- 1 Observatory have larger noise levels than the a b 635 Deep-sea borehole seismological observatories in the Western Pacific vertical component records for periods longer than 20 s. There is a possibility that the horizon- tal sensors in the WP-1 seismometer have a cou- pling problem. In addition, the noise level of the vertical component for period longer than 10 s in the WP-2 Observatory is larger than those of the horizontal component. Because the vertical sen- sor of the WP-2 Observatory may have some Fig. 8c,d. Power spectra of the deep-sea borehole seismic observatories. Power spectra estimated using one-hour records for the all observation period are plotted. HNM and LNM indicate the high noise model and the low noise model by Peterson (1993), respectively. The power spectra are grouped by seasons: c) for vertical component of WP- 2. The vertical component records of the WP-2 Observatory have also larger noise levels in periods longer than 10 s. d) For horizontal component of WP-2. The WP-2 Observatory has quiet noise environment in summer. c d 636 Masanao Shinohara et al. damage, we switched the sensor to the alternative in June 2002. At present, we have not obtained records from the alternative sensor in the WP-2 Observatory. 3.2. Comparison with meteorological data Wind speeds on the Earth surface are consid- ered to increase seismic noise level at high fre- quency (> 0.1 Hz) with increasing velocity (Wil- cock et al., 1999; Collins et al., 2001). A small is- land (Okinotori-shima) lies about 150 km north- east from the WP-1 Observatory. A meteorologi- cal observatory is being operated at the Okinotor- ishima by JAMSTEC, and average wind speed, maximum wind speed, wind direction, air tem- perature, humidity, air pressure, insolation, and radiation are observed every 30 min. Comparison of the noise spectra of the vertical component of the WP-1 seismometer with average wind speed and atmospheric pressure (fig. 9a,b) indicates that wind speed seems to be related to noise levels for periods around a few seconds. Specifically, ty- phoon 200225 passed near the Okinotori-shima Island on November 23, 2002. Large noise levels for a few second periods at WP-1 were observed around November 23, 2002. For the WP-2 Obser- vatory, the high seismic noise level in winter is observed. Although there is no meteorological station near the WP-2, it is known that the north- western Pacific has strong winter winds due to dominant low-pressure weather systems. We in- fer that wind speed is also related with the seis- mic noise level of the WP-2. 3.3. Teleseismic events and performance of event detection The WP-1 and WP-2 deep-sea borehole seis- mic observatories reside in a quiet environment Fig. 9a. Comparison between the noise spectra of vertical component of the WP-1 and the meteorological da- ta (average wind speeds and air pressure) observed at Okinotori-shima, which lies about 150 km northeast of WP-1: from April to September 2002. Rapid decreases of air pressure indicates typhoon passing. The wind speed appears to be related to noise levels in periods around a few second. 637 Deep-sea borehole seismological observatories in the Western Pacific suitable for earthquake observation. Specifically, stable ambient seismic noise levels in marine ar- eas enables us to record many teleseismic events uniformly in time. Figure 10 shows three compo- nent seismograms of the teleseismic event that oc- curred on November 15, 2002 in the region of South Sandwich Island (Ms= 6.6) and was record- ed at the WP-1 Observatory. The seismogram clearly shows minor- and major-arc Love and Rayleigh waves. At present, we have data ob- tained simultaneously from both the WP-1 and WP-2 observatories for events that occurred be- tween March 26 and June 30, 2002. For example, an earthquake that occurred in the Mariana Is- lands region at a depth of 86 km on April 26, 2002 (mb = 6.6) was observed at both the WP-1 and the WP-2 observatories (fig. 11). Simultaneous obser- vation and data recording by both the WP-1 and WP-2 observatories continues to the present. To investigate the performance of the deep- sea borehole seismic observatory, we plotted all vertical seismograms obtained at the WP-2 Ob- servatory from October 29, 2000 to January 21, 2001 and manually picked events from the plot. The seismograms were filtered between periods of 20 and 500 s. A list of recorded events by the WP-2 observatories was compared to a list pub- lished by the USGS (the Quick Epicenter Deter- minations). As a result, the deep-sea borehole ob- servatory proved to record all the teleseismic events with magnitudes greater than 5 at this fre- quency band (fig. 12). Because there is little tem- poral variation of ambient seismic noise, we can obtain more than one seismic event per a day from the deep-sea borehole seismic observato- ries. The WP-2 Observatory records many events that are not included in the list of the QED, US- GS. Most of these events were identified by the Japanese seismic network and their magnitudes are less than 4. The epicentral distances of the re- gional events with magnitudes less than 4 are less than 2000 km. On the other hand, there is no ob- Fig. 9b. Comparison between the noise spectra of vertical component of the WP-1 and the meteorological da- ta (average wind speeds and air pressure) observed at Okinotori-shima, which lies about 150 km northeast of WP-1: from October 2002 to January 2003. Rapid decreases of air pressure indicates typhoon passing. The wind speed appears to be related to noise levels in periods around a few second. 638 Masanao Shinohara et al. Fig. 10. Example of observed earthquake at the WP-1 Observatory. All the components are shown. The records were band-pass filtered at periods from 50 s to 5 s. The earthquake occurred in the region of South Sandwich Is- lands on November 15, 2002, and had a magnitude of 6.6. Epicenteral distance is about 143°. Minor- and ma- jor-arc Love and Rayleigh waves are clearly seen. servation of local earthquake whose S-P time is less than 10 s for both the WP-1 and the WP-2 observatories, because both the WP-1 and the WP-2 are placed in inactive deep-sea basins. 3.5. Comparison with previous deep-sea borehole observations Prior to our observation, several deployments of broadband seismometers into boreholes on the seafloor had been carried out and ambient seis- mic noise spectra were obtained in the Atlantic Ocean and the Pacific Ocean off Hawaii (Mon- tagner et al., 1994; Beauduin and Montagner, 1996; Stephen et al., 1999; Collins et al., 2001). We compare the ambient seismic noise spectra from the WP-1 and the WP-2 observatories with those in previous deep-sea borehole observations (fig. 13a,b). For both vertical and horizontal com- ponents, noise levels in periods smaller than a few seconds are similar, however there are some differences for periods greater than 10 s. For the vertical component, the WP-2 Observatory has larger noise level than the other deep-sea bore- hole observatories in periods between 10 and 100 s. On the other hand, the WP-1 Observatory and the OSN-1 Observatory, the latter of which was installed in the Pacific Ocean off Hawaii, are qui- et in this frequency band for the vertical compo- nent. Noise levels of both observatories are com- parable to those of quietest seismic station on land at periods between 10 s and 30 s. There is a possibility that at least one of the sensors for ver- 639 Deep-sea borehole seismological observatories in the Western Pacific Fig. 11. The records of earthquakes observed si- multaneously by both the WP-1 (upper) and the WP- 2 (lower) observatories. A one hour records of all the component from 16:00:00, April 26, 2002 are shown. No filter is applied. The earthquake occurred in Mar- iana region and its magnitude was 6.6. Fig. 12. Magnitude distribution of earthquakes rec- orded by the WP-2 Observatory from October 29, 2000 to January 21, 2001 with epicentral distance (large symbols). Plus signs and dots refer to body wave mag- nitude determined by the USGS. Solid circles and squares relate to surface wave magnitude. Small dots and squares denote the magnitude of earthquakes by the USGS, which were not detected by the WP-2 Ob- servatory. Almost all events with magnitudes greater than 5 are observed in the borehole observatories. tical component of the WP-2 Observatory was damaged during installation. Although the JT-1 observatory has a peak in noise levels near a pe- riod of 100 s in the horizontal component, the WP-2 Observatory has no such peak. This peak is explained by the ocean gravity wave, and we in- fer that WP-2 escapes from the noise due to in- stallation into the basement deep below the sea- floor (Araki et al., 2004). The noise levels record- ed by the horizontal component for periods greater than 10 s in the WP-1 Observatory are larger than those in the other observatories. Sen- sor coupling or mechanical problems may ac- 11 12 640 Masanao Shinohara et al. count for these results from the WP-1 Observato- ry. Generally, the noise levels of the WP-1 and the WP-2 observatories are comparable with those of previous observations in seafloor boreholes and land seismic stations. We confirm that seismic observation in deep-sea boreholes gives the best environment for earthquake observation in ma- rine areas. 4. Conclusions In 2000 and 2001, the seafloor borehole seis- mological observatories WP-1 and WP-2 were successfully installed in the northwestern Pacific. The WP-1 site is in the west Philippine Basin west of the Kyushu-Palau ridge. The WP-2 Ob- servatory is situated on normal oceanic Mesozoic crust in the northwestern Pacific Basin. Both ob- servatories fill important observational gaps in the worldwide seismic network, since no other land site can replace these sites. Each observato- ry has two identical broadband seismometers, which are cemented near the bottom of the hole. The WP-1 Observatory was activated in March 2002. At present, seismic records of 408 days in total have been obtained from the WP-1 Observa- tory. The WP-2 Observatory was activated in Oc- tober 2000. Approximately fourteen-months of data were retrieved from the WP-2 Observatory. The long-term variations of broadband seis- mic noise spectra (3 mHz-10 Hz) in the north- western Pacific Basin were revealed. The noise level above a period of about 10 s is stable in time. The vertical component of WP-2 has noise levels of about −145 db. Noise levels for the hor- izontal component in WP-2 are lower than that of the vertical component (−160 db in periods greater than 100 s). Because there is a possibili- ty that this vertical sensor was damaged, we ac- tivated an alternative seismometer and shut down the sensor that had been used during the third ROV visit. It is found that the noise levels of the vertical component at WP-1 reach −180 db in pe- riods between 10 s and 100 s. On the other hand, small temporal variations (maximum fluctuation is 10 dB) of noise levels in periods around a few seconds are seen; the WP-1 station and the WP- 2 Observatory have higher noise levels in sum- mer and in winter, respectively. From compari- son with meteorological data observed at a small island near the WP-1 Observatory, wind speed Fig. 13a,b. Comparison of ambient seismic noises between the station in this study and those in previous stud- ies: a) for vertical component; b) for horizontal component. OFP and OSN-1 indicate borehole observatories in North Atlantic Ocean (Montagner, 1994) and the Pacific Ocean off Hawaii (Stephen et al., 1999), respectively. At present, observations at both these stations have been discontinued. HNM and LNM indicate the high noise model and the low noise model by Peterson (1993), respectively. The noise levels of the WP-1 and WP-2 obser- vatories are comparable with those of the previous studies. There is no horizontal record for the OFP. a b 641 Deep-sea borehole seismological observatories in the Western Pacific appears to be related to the noise levels in peri- ods around a few seconds. Due to the low seismic noise environment, many events were recorded in the records from both the deep-sea borehole observatories. It is possible to record teleseismic earthquakes with magnitude greater than 4.5 within an epicentral distance of 45°. We confirm that seismic obser- vation in deep-sea borehole gives the best envi- ronment for long-term, low-noise, high-resolu- tion earthquake observation in marine areas. Acknowledgements The success of the observations was made possible by the active co-operation of many scien- tists, engineers, technicians, ship officers and crew, and ROV operators from various institutions in the world. In particular, we express thanks to Drs. William W. Sager, Matthew H. Salisbury, Carlota Escutia, Carl Richter, Mr. Mike Storms and many people from ODP who led successful installations of the borehole observatories. The skillful maneuvers of the ROV by the KAIKO team, JAMSTEC are acknowledged. We thank Drs. Ralph A. Stephen, Hajime Shiobara, Hitoshi Mikada, Kenji Hirata, Kimihiro Mochizuki, Messrs. Michio Arisaka, Masakazu Ito for fruitful discussions and active support on this study. We would like to thank two anonymous reviewers for their thoughtful reviews and helpful comments. The comments by Dr. Daniel Curewitz were also helpful for improving the English of this manu- script. This study was partly supported by the Ocean Hemisphere Project from the Ministry of Education, Culture, Sports, Science and Technol- ogy of Japan. Most of the figures were created us- ing GMT (Wessel and Smith, 1998). REFERENCES ARAKI, E., M. SHINOHARA, I.S. SACKS, A. LINDE, T. KANAZAWA, H. SHIOBARA, H. MIKADA and K. SUYEHI- RO (2004): Improvement of seismic observation in the ocean by use of seafloor boreholes, Bull. Seismol. Soc. Am., 94, 678-690. BEAUDUIN, R. and J.P. MONTAGNER (1996): Time evolution of broadband seismic noise during the French pilot experi- ment OFM/SISMOBS, Geophys. Res. Lett., 23 (21) 2995-2998. COLLINS, J.A., F.L. VERNON, J.A. ORCUTT, R.A. STEPHEN, K.R. PEAL, F.B. WOODING, F.N. SPIESS and J.A. HILD- BRAND (2001): Broadband seismology in the oceans: les- sons from the ocean seismic network pilot Eexperiment, Geophys. Res. Lett., 28 (1), 49-52. HASVOLD, Ø., H. HENRIKSEN, E. MELVÆR, G. CITI, B.Ø. JO- HENSEN, T. KJØNIGSEN and R. GALETTI (1997): Sea-water battery for subsea control systems, J. Power Sources, 65, 253-261. ION/ODP INTERNATIONAL WORKSHOP (1995): Multidisci- plinary Observatories on the Deep Seafloor, Marseille (France). KANAZAWA, T., K. SUYEHIRO, N. HIRATA and M. SHINOHARA (1992): Performance of the ocean broadband downhole seismometer at Site 794, Proc. ODP, Sci. Results, 127/ 128, pt2, 1157-1171. KANAZAWA, T., W.W. SAGER, C. ESCUTIA and SHIPBOARD SCI- ENTIFIC PARTY (2001): Northwest Pacific seismic obser- vatory and Hammer Drill tests, Sites 1179-1182, Proc. ODP, Init. Rep., 191 (CD-ROM). MONTAGNER, J.P., J.F. KARCZEWSKI, B. ROMANOWICZ, S. BOUARICHA, P. LOGNONNÉ, G. ROULT, E. STUTZMANN, J.L. THIROT, J. BRION, B. DOLE, D. FOUASSIER, J.C. KOENIG, J. SAVARY, L. FLOURY, J. DUPOND, A. ECHARDOUR and H. FLOC’H (1994): The French pilot experiment OFM-SIS- MOBS: first scientific results on noise level and event de- tection, Physics Earth Planet. Inter., 84, 321-336. PETERSON, J. (1993): Observations and modeling of seismic background noise, US Dep. Inter. Geol. Surv., Open-File Rep. 93-322. ROMANOWICZ, B., D. STAKES, J.P. MONTAGNER, P. TARITS, R. UHRHAMMER, M. BEGNAUD, E. STUTZMANN, M. PASYA- NOS, J.F. KARCZEWSKI, S. ETCHEMENDY and D. NEUHAU- SER (1998): MOISE: a pilot experiment towards long term seafloor geophysical observatories, Earth Planets Space, 50, 927-937. SACKS, I.S., K. SUYEHIRO, G.D. ACTON and SHIPBOARD SCIEN- TIFIC PARTY (2000): Western Pacific Geophysical Obser- vatories, Sites 1150 and 1151, Proc. ODP, Init. Rep., 186 (CD-ROM). SALISBURY, M.H., M. SHINOHARA, C. RICHTER and SHIPBOARD SCIENTIFIC PARTY (2002): Seafloor observatories and the Kuroshio current, Proc. ODP, Init. Rep., 195 (CD-ROM). STEPHEN, R.A., J.A. COLLINS and K.R. PEAL (1999): Seafloor seismic stations perform well in study, Eos, Trans. Am. Geophys. Un., 80, 592. SUYEHIRO, K., T. KANAZAWA, N. HIRATA, M. SHINOHARA and H. KINOSHITA (1992): Broadband downhole digital seis- mometer experiment at Site 794: a techinical paper, Proc. ODP, Sci. Results, 127/128, pt2, 1061-1073. SUYEHIRO, K., E. ARAKI, M. SHINOHARA and T. KANAZAWA (2002): Deep-sea borehole observatories ready and cap- turing seismic waves in the Western Pacific, Eos, Trans. Am. Geophys. Un., 83 (621), 624-625. WEBB, S.C. (1998): Broadband seismology and noise under the ocean, Rev. Geophys., 36, 105-142. WESSEL, P. and W.H.F. SMITH (1998): New improved version of the generic mapping tools released, Eos, Trans. Am. Geophys. Un., 79, 579. WILCOCK, W.S.D., S.C. WEBB and I.T. BJARNASON (1999): The effect of local wind on seismic noise near 1 Hz at the MELT site and on Iceland, Bull. Seismol. Soc. Am., 89, 1543-1557.