Microsoft Word - Srivastava et. al _104-113_.doc R C O S T N Publisher: Research Council of Science and Technology, Biratnagar, Nepal p. 104 BIBECHANA A Multidisciplinary Journal of Science, Technology and Mathematics ISSN 2091-0762 (print), 2382-5340 (online) Journal homepage: http://nepjol.info/index.php/BIBECHANA Implementation of designed jigs and fixtures for hand operated press in production of mainframe for paddy-weeder Ankitesh Shrivastava 1* , S.K. Ganguly 2 , Ajay Verma 3 1 Production Engineering, Bhilai Institute of Technology, Durg (C.G.), India. 2 Mechanical Engineering Department, Bhilai Institute of Technology, Durg (C.G.), India. 3 Farm Machinery & Power Engineering, Indira Gandhi Agricultural University, Raipur (C.G.), India. *Email: ankiteshrivastava@gmail.com Accepted for publication: December 18, 2014 Abstract The main purpose of paddy weeder is to dislocate the weeds present in paddy fields. The operation, when done manually causes drudgery in workers, which in turn reduces their efficiency in fields. Paddy weeder proved to be efficient enough to perform the work manually with less efforts & time consumed. The product was being manufactured by traditional methods, i.e. without implementation of jigs & fixtures. The paper presents a procedure for inclusion of designed & developed jigs and fixtures in the production of paddy weeder, and hence fulfills the need of mass production. The designed jigs proved quite efficient & were helpful in reduction of 50 % in welding operations performed. Hence, it is helpful in enabling mass production. DOI: http://dx.doi.org/10.3126/bibechana.v12i0.11672 © 2014 RCOST: All rights reserved. Keywords: Designed jigs & fixtures; hand operated press; production; paddy-weeder. 1. Introduction Weeds are the plants which grow, in a region where they are not desired. Paddy weeder is agricultural equipment used to remove weeds from a desired area. One of the major laborious and time consuming operations in rice cultivation is weeding. The concept of weed control is as old as agriculture itself. The global figure for crop yield loss is accepted as 10% of actual yield [1]. To get the full benefit of mechanization it is very necessary to use proper weeding implements, which will reduce drudgery and cost of cultivation [2]. Study was conducted by [3] to evaluate and compare the inputs of manual energy only and manual-cum-mechanical energy in the production of ground-nuts. Study revealed that weeding had the most energy requirement (45% and 52% of the mean total energy inputs) in ground- nut cultivation. The human labour output capacity is increased by 8 – 10 times in weeding by the use of mechanical weeder [4]. Jig is a special tool used for locating and firmly holding work piece in the proper position during the manufacturing or assembly operation. It also guides the tool or work piece during the operation. Jig is designed to increase the productivity of operation assisting worker to do job easier, faster and more comfortable [5]. Fixtures are mechanism used to rapidly, accurately, and securely position workpiece Shrivastava et al./ BIBECHANA 12 (2015) 104-113: p. 105 during machining such that all machined parts fall within the design specifications. This accuracy facilitates the interchangeability of parts. The goal of research was to find appropriate systematic approach to quality improvement in the production preparation, within the frame of metal production. Starting from the main principles and methodologies of manufacturing process quality improvement, in the paper are identified possibilities of integration of methods and tools in an operational model of quality improvement in the process of production preparation [6]. The implementation of power press into the production operation was not a feasible alternative, as the pressure developed by it would be way too much. As the desired outcome was just to get a bend of 900 on MS plates of 6mm thickness, its implementation would lead towards more time consumption in the process, with added quantity of scrap. 2. Problem Statement Keeping an eye on the huge demand of the paddy weeder in the present scenario, and on the other hand workers presently operating without jigs and fixtures, the parts were welded using visual observations which resulted in in-accuracy in dimensions, and poor workmanship & lack of interchangeability. Jigs to serve for the sole purpose has been designed and developed at Faculty of Agricultural Engineering workshop. Mass production aims at high productivity to reduce unit cost and interchangeability to facilitate easy assembly. This necessitates production devices to increase the rate of manufacture and inspection device to speed-up inspection procedure. Nowadays new machine tools, high-performance cutting tools, and modern manufacturing processes enable industries to produce parts faster and better than ever before. To counterbalance the need and production, implementation of jigs and fixtures in the production line is extremely important to produce good parts with low cost and high quality. When changes in a manufacturing method are proposed, it is first necessary to assess the extent of the change. Similarly, in consideration of paddy weeder the change should be within the limits defined for the parameters of manufacturing process. In this case, since the whole process had been demonstrated to yield product that meets the design intent, change within the process can be allowed with no further process validation. Based on this evaluation, it was found that there were processes that need upgrading for enabling mass-production with less time consumed and material wastage with higher accuracy. Since there were a lot of parameters that needed the attention, hence the need to design the jigs for the processes emerged. Jig is one of the most important components in the processes for manufacturing precision parts in mass production. Both the material costs and manufacturing time will be decreased in many of the process involved in manufacturing steps, this means the cost of these steps would be reduced as a result as well. 3. Materials and Methods Considerations while designing jigs and fixtures Designing of jigs and fixtures depends upon so many factors. These factors are analyzed to get design inputs for jigs and fixtures. The list of such factors is mentioned below- (a) Study of work piece and finished component size and geometry. Shrivastava et al./ BIBECHANA 12 (2015) 104-113: p. 106 (b) Type and capacity of the machine, its extent of automation. (c) Provision of locating devices in the machine. (d) Available clamping arrangements in the machine. (e) Available indexing devices, their accuracy. (f) Evaluation of variability in the performance results of the machine. (g) Rigidity and of the machine tool under consideration. (h) Study of ejecting devices, safety devices, etc. (i) Required level of the accuracy in the work and quality to be produced. Main-frame The main frame of the paddy weeder consists of two metal plates of 205mm each, one plate of 125mm, are weld together at 900 (Fig. 1). Fig. 1: Frame manufactured traditionally. A different metal plate is taken with dimensions 405mm, and was bent with the help of a handmade fixture (Fig.2). The part is called float, as it skids over the fields so as to facilitate proper working of equipment. Shrivastava et al./ BIBECHANA 12 (2015) 104-113: p. 107 Fig. 2 Hand-made jig for bending float Table 1 shows the amount of welding operations being performed, while manufacturing the equipment’s frame traditionally. Table 1: Welding operation for traditional method S. No. Name of part No. of welding operations 1 Weeder frame 02 2 Joining frame with float 02 Total 04 Shrivastava et al./ BIBECHANA 12 (2015) 104-113: p. 108 Design of jigs & fixtures To facilitate the fast manufacturing process for the production, jigs and fixtures were designed on designing software solid works 2012. Fig.3(a) Fixture be fixed on bending machine Fig. 3 (b) Jig for bending float Shrivastava et al./ BIBECHANA 12 (2015) 104-113: p. 109 For bending float, set of jigs & fixtures were developed to facilitate the bending of float, the MS plates cut after the marking operation were placed on the elevated corners (Fig. 3(a)) and the other fixture was made to be fixed on the bending machine (Fig. 3(b)), with the help of nuts and bolts. Fig. 4: Designed jig for bending at right angles. A solution was needed for replacing welding with the bending operation and hence a jig was designed to serve for this purpose. The plates were bent with the help of a set of jigs and fixtures, plates were placed on the elevated surface (Fig. 4), and were pressed with the help of bending machine and hence creating a bend of 90 0 , and eliminating the need of welding operation to remarkable extent. 4. Results and Discussion Hand operated press The jigs and fixtures designed for the weeder were developed and were made to serve the sole purpose of reducing the time consumed in the production with less efforts to be laid for operations (Fig. 5). Hand operated press was used instead of power press, to reduce the complexity of operation and to ensure the mobility of operation. Shrivastava et al./ BIBECHANA 12 (2015) 104-113: p. 110 Fig. 5 Hand operated press Developed jigs & fixtures The purpose of designing a jig for paddy weeder was to eliminate the time consumption in process and increase the quality of the product. The jig and fixture designed for bending the float was hence developed (Fig.6 & 7) in accordance with the design produced. Fig. 6 Developed fixture for bending the float Shrivastava et al./ BIBECHANA 12 (2015) 104-113: p. 111 Fig. 7 Developed jig for bending float. The jig and fixture developed for producing frame (Fig.8) with minimum number of welding operations involved, desired the plates to be bent at an angle of 90 0 . Fig. 8 Developed jig for bending plates Shrivastava et al./ BIBECHANA 12 (2015) 104-113: p. 112 Fig.9 shows the jig and fixture setup on the bending machine, which uses mechanical force to create bends. The jigs were designed so as to reduce the welding operation. Fig. 9 Set of jig &fixture for manufacturing frame The new developed jigs and equipments helped in reducing the number of welding operations to half, i.e. two (Fig.10) Fig. 10 Frame manufactured by jigs & fixtures Shrivastava et al./ BIBECHANA 12 (2015) 104-113: p. 113 5. Conclusion The developed jigs & fixtures according to the designs generated, proved helpful in reducing the time elapsed in manufacturing by reducing the number of times an operation was being performed to achieve the goal. The reduction in operations to half, proved helpful in reducing the time consumed in manufacturing operation. Hence, the goal of enabling mass-production was achieved. References [1] W.W. Fletcher, Recent Advances in Weed Science. Introductory Chapter.(Ed W.WFletcher) Commonwealth Agricultural Bureaux. The Gresham Press: Surrey, UK, (1983) pp1–3. [2] R. Remesan, M.S. Roopesh, N. Remya, P.S. Preman, Wet Land Paddy Weeding- A Comprehensive Comparative Study from South India. Agricultural Engineering International: the CIGR Journal, 9 (2007). [3] B. Umar, Agricultural Engineering International: The CIGR Journal of Scientific Research and Development, (2003) 1-11. [4] B.P. Mishra, V.K. Panday, D.K. Dwivedi, Effect of different weeding methods on energy and economic management under Khura rice cultivation system. All India seminar of Agril. Engineers, Institution of Engineers, India (1993). [5] A. Saptari, W.S. Lai, M.R. Salleh, Jordan Journal of Mechanical and Industrial Engineering, 5(1) (2011) 9-16. [6] D. Pavletic, M. Sokovic, International Journal for Quality research, 3(4) (2009) 309-315.