Microsoft Word - 3debree.docx CHEMICAL ENGINEERING TRANSACTIONS VOL. 54, 2016 A publication of The Italian Association of Chemical Engineering Online at www.aidic.it/cet Guest Editors: Selena Sironi, Laura Capelli Copyright © 2016, AIDIC Servizi S.r.l., ISBN 978-88-95608-45-7; ISSN 2283-9216 Determining Separation Distances to Avoid Odour Annoyance With Two Models for a Site in Complex Terrain Martin Piringera, Werner Knaudera, Erwin Petza, Günther Schaubergerb aCentral Institute for Meteorology and Geodynamics, Department of Environmental Meteorology, Hohe Warte 38, A 1190 Vienna, Austria bWG Environmental Health, Department of Biomedical Sciences, University of Veterinary Medicine Vienna, Veterinärplatz 1, A-1210 Vienna, Austria martin.piringer@zamg.ac.at Direction-dependent separation distances to avoid odour annoyance, calculated with the Gaussian Austrian Odour Dispersion Model AODM and the Lagrange particle diffusion model LASAT for a site in complex terrain, will be analysed and compared. The relevant short-term peak odour concentrations are calculated with a stability-dependent peak-to-mean algorithm. For both models, the same emission and meteorological data, but model-specific atmospheric stability classes have been used. The estimate of atmospheric stability is obtained from three-axis ultrasonic anemometers using the standard deviations of the three wind components and the Obukhov stability parameter. In addition, separation distances are also determined for an odour threshold of 0.25 (factor 4) of the German TA Luft (Technical Guideline for Clean Air) uniquely applied over all stability conditions and distances. The results are demonstrated for the Austrian village Weissbach in the narrow Saalach valley. Meteorological data at this site are provided by a three-axis ultrasonic anemometer from which also stability information (Obukhov stability parameter, OSP) is directly deduced. Separation distances are determined for two odour impact criteria, namely exceedence probabilities of 3 and 8 %, each in combination with the odour threshold of 1 ouE/m 3. The form of the separation distances around the fictitious odour source depends strongly on the prevailing meteorological conditions (wind and stability), on the odour impact criteria and on the peak-to-mean factors. 1. Introduction Separation distances to protect the neighbourhood from odour annoyance can be obtained from dispersion models. Such models predict the ambient odour concentration on an hourly or half-hourly basis. To account for the ability of the human nose to perceive odour within a single breath, the authors have developed and already published a peak-to-mean approach used with the Austrian Odour Dispersion Model (AODM), a Gaussian model adapted for the prediction of odour sensation (Schauberger et al., 2000; Piringer et al., 2007; Piringer et al., 2014). This approach is here used also with the Lagrangian particle diffusion model LASAT in a post-processing mode as described in Piringer et al. (2015). Both models can now calculate direction- dependent separation distances for a prescribed combination of odour threshold and exceedance probability which are a function of the prevailing atmospheric stability conditions. This is demonstrated for a site in complex terrain. 2. Material and methods The Austrian odour dispersion model (AODM, Piringer et al., 2007; Piringer et al., 2013; Schauberger et al., 2000; Schauberger et al., 2013; Schauberger et al., 2002) estimates mean ambient concentrations by the Austrian regulatory dispersion model (Österreichisches Normeninstitut, 1996; Kolb, 1981) and transforms these to instantaneous values depending on the stability of the atmosphere (Section 2.2). The model uses a traditional discrete stability classification scheme with dispersion parameters developed by Reuter (1970). DOI: 10.3303/CET1654002 Please cite this article as: Piringer M., Knauder W., Petz E., Schauberger G., 2016, Determining separation distances to avoid odour annoyance with two models for a site in complex terrain, Chemical Engineering Transactions, 54, 7-12 DOI: 10.3303/CET1654002 7 The dispersion model LASAT (Janicke Consulting, 2013) simulates the dispersion and the transport of a representative sample of tracer particles utilizing a random walk process (Lagrangian simulation). It computes the transport of passive trace substances in the lower atmosphere (up to heights of about 2000 m) on a local and regional scale (up to distances of about 150 km). LASAT as well as AUSTAL2000 are usually run with the Klug-Manier stability scheme (TA Luft, 2002). The peak-to-mean approach used to transform the half-hourly model concentrations into short-term peak values as well as the scheme to transform the Obukhov stability parameter OSP [m-1] to atmospheric stability classes depending on the local roughness length z0 [m] are described in full detail in Piringer et al. (2014). The Obukhov stability parameter and the standard deviations of the three wind components are derived from a one-year time series of ultrasonic anemometer measurements. Sonic anemometers measure the along-path velocity components from the travel time of acoustic waves between transducers separated about 10-20 cm. In addition to the three-dimensional wind vector, the sound velocity is derived, from which the so-called “sonic temperature” is calculated. The measurement of sonic temperature fluctuations is necessary to calculate the sensible heat flux. Other quantities which are derived from sonic measurements are the means, standard deviations, and co-variances of the wind components and the momentum flux, the Obukhov stability parameter, and the friction velocity. Sonic anemometers usually sample at 10 Hz, and the data are usually stored as averages over 10 minutes or half an hour. The investigation has been carried out for Weissbach near Lofer (12.789 E, 47.498 N, at 678 m asl.), situated in the Saalach valley in the county of Salzburg which at the site stretches from SE to NW. The valley with approx. only 1 km in width is relatively narrow, flanked by steep slopes of heights of several hundred meters. For all model runs, the same source data are used (Piringer et al., 2015). Besides using the peak-to-mean algorithm, separation distances are also determined for an odour threshold of 0.25 (factor 4) of the German TA Luft (Technical Guideline for Clean Air) uniquely applied over all stability conditions and distances. 3. Results 3.1 Meteorological conditions Due to the topographical situation at Weissbach, the wind is channelled along the valley axis. Up-valley flow is from NW, down-valley flow from SE (Fig. 1). The down-valley flow from SE shows a larger fraction of weaker winds, but also a slightly larger amount of stronger winds than the up-valley flow. The strong southerly winds might also be associated with Foehn events. Figure 1: Wind rose for Weissbach (01.09.2010 – 31.08.2011); colour coding denotes wind speed 8 The frequency of stability classes is determined from the OSP with a roughness length and 0.5 m in Weissbach. From Fig. 2, the frequency distribution is roughly 30:30:40 for unstable-neutral-stable conditions. The LASAT scheme calculates slightly more stable and less unstable conditions. Neutral conditions are more frequent with the LASAT scheme. Class 5 has no appropriate counterpart in the LASAT scheme. Figure 2: Relative frequency [%] of stability classes at Weissbach 3.2 Attenuation curves Site-specific attenuation curves for each stability class obtained from the ultrasonic anemometer measurements are presented in Fig. 3. The peak-to-mean ratios depend on the models because they use different stability classification schemes. Unstable classes are most relevant at Weissbach, for both models, the peak-to-mean ratios starting at high values near the source and approaching 1 at about 200 m. All in all, the AODM and LASAT curves in Fig. 3 do not differ much. Figure 3: Peak-to-mean ratios for Weissbach derived from ultrasonic anemometer data (OSP) using the conversion to stability classes for AODM (left) and for LASAT (right) 3.3 Separation distances Direction-dependent separation distances are calculated for two odour impact criteria used in Austria: 1 OUE/m 3 and 3 % exceedance probability, representative for recreation areas (high odour protection), 1 OUE/m 3 and 8 % exceedance probability, representative for residential areas mixed with commercial activity (lower odour protection). The separation distances are shown as isolines in Fig. 4, encompassing the area of 9 exceedance of the given thresholds. The larger the area, the more unfavourable is the odour impact criterion. AODM results (left) are compared to LASAT results (right) for the same scenario. The shape of the separation distances is strongly influenced by the wind directions in Weissbach (Fig. 1) and by atmospheric stability (Fig. 2). The peak-to-mean ratios play a minor role, as they approach 1 after 200 to 300 m (Fig. 3). An elongation along the valley axis is observed which is due to the valley wind system. Using AODM, maximum separation distances for an exceedance probability of 3 % are about 600 m towards NW and about 500 m towards SE; with 8 %, these distances are about 300 m in both directions (Fig. 6, left). The calculation with LASAT leads to a considerable increase of separation distances for an exceedance probability of 3 % (Fig. 6, right) compared to AODM. For 8 %, however, maximum separation distances calculated with LASAT only slightly increase to about 400 m in both directions, compared to the AODM results. Figure 4: Direction-dependent separation distances [m] with (left) AODM and (right) LASAT for 1 OUE/m 3 and 3 % (blue) and 8 % (orange) exceedence probability with peak-to-mean ratios derived from ultrasonic anemometer measurements at Weissbach Figure 5: Direction-dependent separation distances [m] with (left) AODM and (right) LASAT for 1 OUE/m 3 and 3 % (blue) and 8 % (orange) exceedence probability with the factor 4 of the German TA Luft (2002) for Weissbach 10 Using a constant factor 4 over all stability conditions and distances in combination with OSP-derived stability classes results in by far the largest separation distances for both models (Fig. 5). This is clearly a result of this factor dominating over the peak-to-mean ratios derived from ultrasonic anemometer measurements at distances over 100 m (Fig. 3). Along-valley maximum separation distances are well outside the area displayed, with the exception of the downvalley direction and 8 % exceedance probability for AODM (Fig. 5, left). Again, separation distances with LASAT are larger and comprise a bigger area than those with AODM. This is due to the fact that the stability classification scheme used with LASAT comprises more stable cases than that with AODM (Fig. 2). The largest separation distances are calculated for stable dispersion categories. The along-valley wind directions at Weissbach are often associated with stable conditions. The channelling of the flow in combination with frequent stable conditions causes high odour concentrations and leads to enhanced separation distances at Weissbach compared to a flatland site. This enhanced frequency apparently compensates for the peak-to-mean ratios which are not relevant at Weissbach for large separation distances. While the separation distances for the peak-to-mean ratios in Fig. 3 with up to several hundred meters are within a plausible range (Fig. 4), this is certainly not the case for the large separation distances in Fig. 5 (see also the discussion in Piringer et al., 2015). 4. Conclusions In this paper, direction-dependent separation distances to protect the neighbourhood from odour nuisance have been calculated with two models, the Gaussian Austrian Odour Dispersion Model AODM and the Lagrange particle diffusion model LASAT. Short-term peak odour concentrations have been calculated either with the stability-dependent peak-to-mean algorithm developed with AODM (Piringer et al., 2014) or with the factor 4 – approach used with LASAT in Germany (TA Luft, 2002). The same emission and meteorological data have been used, but atmospheric stability is determined from different stability schemes used with the models. Differences in the resulting separation distances are then both due to the different peak-to-mean concepts and to the different atmospheric stability schemes. The results are demonstrated for Weissbach near Lofer, a rural site in the narrow Saalach valley in the county of Salzburg. On-site meteorological conditions are presented in Figs. 1 and 2. The wind is channelled along the valley axis. The down-valley flow from SE shows a larger fraction of weaker winds, but also a slightly larger amount of stronger winds than the up-valley flow. The strong southerly winds might also be associated with Foehn events. The frequency distribution of stability classes is roughly 30:30:40 for unstable-neutral-stable conditions. The LASAT scheme calculates slightly more stable and less unstable conditions than the scheme used with AODM. Neutral conditions are more frequent with the LASAT scheme. The maximum of the separation distances occurs in all cases along the main valley axis. Applying the factor 4 gives by far the largest separation distances, because this factor dominates over the peak-to-mean ratios deduced from ultrasonic anemometer data from about 100 m onwards. LASAT calculates larger separation distances than AODM. This is attributed to the fact that the Klug-Manier scheme used with LASAT shows a tendency to deliver more stable cases than the Reuter scheme used with AODM. Probably more important, LASAT, in contrast to the stationary concentration fields of AODM, calculates concentrations as long as the trajectories stay within the model domain, thus likely increasing residence times and also separation distances. Acknowledgement This work has been kindly funded by the Austrian Climate Research Programme ACRP within the current project “Climate change and future pig and poultry production: implications for animal health, welfare, performance, environment and economic consequences”, project number B567131, duration: 01.04.2016 – 31.03.2018, in which the methodology to calculate separation distances presented here will be applied. References Janicke Consulting, 2013, Dispersion model LASAT. Reference/Working Book for Version 3.3. Kolb, H., 1981, Ein normatives physikalisches Modell zur Simulierung der Ausbreitung von Schadstoffen in der Atmosphäre mit besonderer Berücksichtigung der Verhältnisse in Österreich. Publ. d. Lehrk. f. theoret. Met., Institut für Meteorologie und Geophysik, Universität Wien, vol. 29. Piringer, M., Knauder, W., Petz, E. & Schauberger, G., 2015, A comparison of separation distances against odour annoyance calculated with two models, Atmospheric Environment 116, 22 – 35. Piringer, M., Knauder, W., Petz, E. & Schauberger, G., 2014, Use of Ultrasonic Anemometer Data to Derive Local Odourrelated Peak-to-mean Concentration Ratios, Chemical Engineering Transactions, 40, 103-108. 11 Piringer, M., Petz, E., Groehn, I. & Schauberger, G., 2007, A sensitivity study of separation distances calculated with the Austrian Odour Dispersion Model (AODM), Atmospheric Environment, 41, 1725-1735. Piringer, M., Petz, E., Groehn, I. & Schauberger, G., 2013, Corrigendum to "A sensitivity study of separation distances calculated with the Austrian Odour Dispersion Model (AODM)" [Atmos. Environ. 41 (2007) 1725- 1735], Atmospheric Environment, 67, 461-462. Reuter, H., 1970, Die Ausbreitungsbedingungen von Luftverunreinigungen in Abhängigkeit von meteorologischen Parametern, Archiv für Meteorologie, Geophysik und Biokimatologie, series. A,, 19, 173- 186. Schauberger, G., Piringer, M. & Petz, E., 2013, Corrigendum to "Diurnal and annual variation of the sensation distance of odour emitted by livestock buildings calculated by the Austrian odour dispersion model (AODM)" [Atmos. Environ. 34 (2000) 4839-4851], Atmospheric Environment, 67, 459-460. Schauberger, G., Piringer, M. & Petz, E., 2002, Calculating Direction-dependent Separation Distance by a Dispersion Model to avoid Livestock Odour Annoyance, Biosyst Eng, 82, 25-37. TA Luft, 2002, Erste Allgemeine Verwaltungsvorschrift zum Bundes–Immissionsschutzgesetz. (Technische Anleitung zur Reinhaltung der Luft – TA Luft). Bundesministerium für Umwelt, Naturschutz und Reaktorsicherheit. ÖNorm M 9440, 1992, Ausbreitung von luftverunreinigenden Stoffen in der Atmosphäre; Berechnung von Immissionskonzentrationen und Ermittlung von Schornsteinhöhen, Österr. Normungsinstitut, Fachnormenausschuss 139 - Luftreinhaltung. 12