CHEMICAL ENGINEERING TRANSACTIONS  
 

VOL. 51, 2016 

A publication of 

 
The Italian Association 

of Chemical Engineering 
Online at www.aidic.it/cet 

Guest Editors: Tichun Wang, Hongyang Zhang, Lei Tian 
Copyright © 2016, AIDIC Servizi S.r.l.,  
ISBN 978-88-95608-43-3; ISSN 2283-9216 

OPNET-based WLAN Modeling and its Performance Testing 
Wei Jiang 
School of Computer & Information, Anqing Normal University, Anqing 246011, China 
wjiang@aqnu.edu.cn  

With the rapid development of wireless communication and network technologies, people have higher demand 
for the network in its free access at any time or place, which prioritizes the convenience of the network. As a 
result, WLAN communication technologies will surely see a stronger momentum. This paper models a WLAN 
for its simulation and performance tests. Then the paper conducts the simulation analysis of the model, and 
systematically analyzes and compares statistics overall and between nodes as well as the simulation 
experiments with different parameters, leading to results that fully achieve WLAN modeling and its performance 
simulation based on the OPNET software.  

1. Introduction 

Wireless Local Area Network (WLAN) is one way to connect the data communication system by wireless 
communication, wireless connections and dots. WLAN sends and receives data through the 
electromagnetic wave instead of the fiber twisted pair cable or traditional LAN coaxial line. Also, WLAN enables 
website browsing, file transfer, traditional network communication, e-mailing, database visiting and peripheral 
sharing. Compared to traditional cable network, WLAN has its advantages in low operating and time cost, 
instant investment and rapid returns, steadiness, extension-friendliness and strong resistance from natural 
environment, landscape and disasters as the flexible and high-efficiency network (Kim et al, 2014; Lin and Chi, 
2005). For recent years, as the IEEE802.11 protocol gets enriched and supplemented, Wi-Fi technology sees 
faster growth. Compared to cable network, wireless network equips with both the mobility of high nodes and the 
convenience of the network, which makes wireless network more suitable to the network scenarios newly built 
or of highly movable nodes, such as on-site investigation and on-spot emergency. In a sense, the wireless 
network extends and supplements the cable network.  
On the other hand, it should be noted that there still exist some problems in WLAN technology compared to 
cable network as follows: the limited brand width and communication distance as well as high error rate and 
mobility (Manodham et al, 2008; Eckhardt and Steenkiste, 1999; Jansons et al, 2012; Vaidya et al, 2005; 
Bianchi, 2006; Cali et al, 2000). Besides, the wireless protocol only covers MAC and physical layer but not the 
amendment of the upper-layer protocol, so the protocol above IP layer still follows the traditional TCP/IP model. 
It is reasonable in terms of network hierarchy, but may exert some negative impact on the working performance 
of upper-layer service (Khan et al, 2013; Willig et al, 2002; Keong and Ming, 2010; Sabra et al, 2013; Maniotis 
et al, 2012; Tseng et al, 2003). Thus, further research is required in this respect.  
OPNET is widely recognized and used in communication, national defense and computer network. 
Webmasters of operators manages the network with the help of network intelligence of OPNET.  
And thanks to its sound openness and inter-connectivity, many popular software on network management and 
monitoring are formulated. As the network is a complicated system, OPNET Modeler classifies the complicated 
modeling system into different layers in line with hierarchy and modularity, with each layer having its specific 
function.  
Also, each layer has more sub-layers with smaller tasks, and each module completes its inner modules. 
OPNET modeler consists of network domain, domain nodes and process domain. From the above-mentioned, 
OPNET can serve as the platform for modeling and test to optimize the network performance. 

                               
 
 

 

 
   

                                                  
DOI: 10.3303/CET1651061

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Please cite this article as: Jiang W., 2016, Opnet-based wlan modeling and its performance testing, Chemical Engineering Transactions, 51, 
361-366  DOI:10.3303/CET1651061   

361

file:///C:/Users/MS_PC/AppData/Local/Yodao/DeskDict/frame/20160119165938/javascript:void(0);
file:///C:/Users/MS_PC/AppData/Local/Yodao/DeskDict/frame/20160119165938/javascript:void(0);


2. WLAN network modeling 

The latest version OPNET 14.5 is used in this paper for modeling. The first step to build a new network model is 
to set up a new project and a new scenario in this project. The Startup Wizard is done step by step in this paper 
as the following procedures: 1. Choosing the type of network topology; 2. Setting the coverage and size of the 
network; 3. Setting the background image of the network; 4. Choosing the target model family. 

 

Figure 1: OPNET modeller 14.5-input of project and scenario name 

Create an empty scenario, click “next” to choose the network type and scenario size that can be set as will. In 
the modeler menu, choose nodes of simulating network topology and the debugging module of network 
operating parameters in network service setting in the description of link features to run the simulation. The 
required family models are 3Com, Ethernet and wireless_lan. After all these steps, click “next” to verify the 
correctness of the parameters chosen, then click “finish” to complete the setting of parameters. Figure 2 below 
shows the whole process. 

 

Figure 2: Setting of Network Type and Scenario Size 

After the scenario setting, the network model is to be built. Choose needed network node models from the object 
panel, namely the switch, Ethernet server, wireless AP and wireless terminal, and then put them in the prepared 
setting. Connect the switch to Ethernet server and to the wireless AP by 10BaseT Link Model. Select 
3C_CB2500_4s_e16_fe switch model, needed models of Ethernet server, wireless AP and wireless terminal to 
build the network. The number of wireless terminals can be set randomly. The terminal communication go 
across the AP, then enter Ethernet server through the router to get access to the internet, as the figure below 
demonstrates. By this step, the network model has been basically built. If there are no errors identified or steps 
missed, the following WLAN simulation can begin (Figure 3 and Figure 4).  

 

Figure 3: Picture of simulation scenario   

362



 

Figure 4: Picture of inner structure of nodes 

3. The result and analysis of simulation experiments 

Before simulation experiments, parameters of the model should be known. Figure 5 is the picture of attribute 
parameters of wireless AP, detailing the attributes of wireless interface. The figure shows MAC address of 
WLAN is distributed automatically. Click Wireless LAN Parameters, then attributes of wireless AP interface can 
be seen from the pull-down menu, such as data rate, RTs threshold, low and high retry limit. 
 

 

Figure 5: Parameters of wireless AP 

 

Figure 6: Graph of traffic received of bank node   

363



 

Figure 7: Graph of traffic received of bank node 

Figure 6 is the graph of traffic received of Bank node. The abscissa means simulation time which is 3 hours 
totally, while the ordinate refers to the value of traffic received with the unit as bytes/sec. 
 

 

Figure 8: Graph of traffic sent of bank node     

 

Figure 9: Graph of traffic sent of laptop_0 under hotel, hotel_0 and hotel_1 nodes 

Figure 7 and Figure 8 refers to traffic received and sent of Bank node. The abscissa means simulation time 
totaling 3 hours, while the ordinate refers to the value of traffic received with the unit as bytes/sec. From the 
figures, it can be seen that the curves of traffic received and sent at the same time are consistent with each 
other. 

364



Figure 9 is the graph of traffic sent of laptop_0 under Hotel, Hotel_0 and Hotel_1 nodes. The abscissa means 
simulation time totaling 3 hours, while the ordinate refers to the value of traffic sent with the unit as bytes/sec. 
The figure shows the traffic sent of laptop_0 under Hotel is more than that under Hotel_1 and Hotel_0. 
 

 

Figure 10: Graph of traffic received and sent of bookstore nodes 

 

Figure 11: Graph of data received and sent  

Figure 10 is the graph of traffic received and sent of laptop_0 and laptop_1 under Bookstore nodes. The 
abscissa means simulation time totaling 3 hours, while the ordinate refers to the value of traffic received with 
the unit as bytes/sec. The figure shows, if simulation time is at the range of 0h-1h, laptop_0 receives less traffic 
than laptop_1. But if the time ranges from 1h to 2h, laptop_0 receives more traffic than laptop_1. The traffic 
received is different in different time ranges. 
Figure 11 is the graph of data received and sent. The abscissa means simulation time totaling 3 hours, while 
the ordinate refers to the value of traffic received and sent at the same time with the unit as bytes/sec. The 
figure shows, this WLAN receives much more traffic than it sends. 

4. Conclusion and discussion 

To summarize, this paper builds a WLAN model for simulation and performance test, and conducts the 
simulation analysis of the model. Then the author systematically analyzes and compares statistics overall and 
between nodes as well as the simulation experiments with different parameters. The satisfying results fully 
achieve WLAN modeling and its performance simulation based on OPNET and provide a new and efficient way 
for WLAN network modeling and its performance simulation. 
In nature, WLAN has no big difference from the traditional computer network in many aspects except in the 
transmission media. WLAN can connect networks in places that traditional Ethernet cannot reach, expand the 
network transmission distance, achieve resource sharing by its connect to the existing Ethernet and build an 

365



independent network through wireless terminals. However, regarding current situation, WLAN cannot dominate 
the network, because WLAN or traditional Ethernet is a supplement to each other rather than a replacement. 

Reference 

Bianchi G., 2006, Performance analysis of the IEEE 802.11 distributed coordination function. IEEE Journal on 
Selected Areas in Communications, 18(3): 535-547. DOI: 10.1109/49.840210 

Cali F., Conti M., Gregori E., 2000, Dynamic tuning of the IEEE 802.11 protocol to achieve a theoretical 
throughput limit. IEEE/ACM Transactions on Networking, 8(6): 785-799. DOI: 10.1109/90.893874 

Chang C.Y., Sun H.C., Hsieh C.C., 2005, MCDA: an efficient multi-channel MAC protocol for 802.11 wireless 
LAN with directional antenna. IEEE International Conference on Advanced Information Networking & 
Applications, 2: 64-67. DOI: dx.doi.org/10.1109/AINA.2005.242 

Eckhardt D.A., Steenkiste P., 1999, A Trace-based Evaluation of Adaptive Error Correction for a Wireless Local 
Area Network. Mobile Networks & Applications, 4(4): 273-287. 

Jansons J., Petersons E., Bogdanovs N., 2012, Vehicle-to-infrastructure communication based on 802.11n 
wireless local area network technology. Congress on Future Internet Communications, 26-31. DOI: 
10.1109/BCFIC.2012.6217975 

Keong W.W., Ming L.T., 2010, OS-MDASO: An algorithm that guarantees correctness for P2P object-oriented 
database systems in a wireless local area network environment Information Technology, International 
Symposium in, 3: 1233-1237. 

Khan M.A., Khan T.A., Beg M.T., 2013, Optimization of Wireless Network MAC Layer Parameters. International 
Journal of Innovative Technology, 2(6).  

Kim Y.H., Lee, J., Ryu K.S., Kim J.K., 2014 Method for transmitting information in wireless local area network 
system. US. 

Lin Y.D., Chi P.L., 2005, Tapered Bent Folded Monopole for Dual-Band Wireless Local Area Network (WLAN) 
Systems. IEEE Antennas & Wireless Propagation Letters, 4(1): 355-357. 

Maniotis P., Kalfas G., Alonso L., Verikoukis C., Pleros N., 2012, Throughput and Delay Fairness through an 
agile Medium-Transparent MAC protocol for 60GHz Fiber-Wireless LAN networks. IEEE Wireless 
Communications & Networking Conference, 3769-3773. DOI: 10.1109/WCNC.2012.6524249 

Manodham T., Loyola L., Miki T., 2008, A Novel Wireless Positioning System for Seamless Internet Connectivity 
based on the WLAN Infrastructure. Wireless Personal Communications, 44(3): 295-309. 

Sabra R., Lb U.E., Shuman S., 2013, Collision Detection based on RE Energy Duration in IEEE 802.11 Wireless 
LAN. Communication System Software and Middleware, 25(5): 1-6. 

Tseng Y.C., Hsu C.S., Hsieh T.Y., 2003, Power-saving protocols for IEEE 802.11-based multi-hop ad hoc 
networks. Computer Networks, 43(3): 317-337. 

Vaidya N., Dugar A., Gupta S., Bahl P., 2005, Distributed fair scheduling in a wireless LAN. Mobile Computing 
IEEE Transactions on, 4(6): 616-629. DOI: 10.1109/TMC.2005.87 

Willig A., Kubisch M., Hoene C., Wolisz A., 2002, Measurements of a wireless link in an industrial environment 
using an IEEE 802.11-compliant physical layer. IEEE Transactions on Industrial Electronics, 49(6): 
1265-1282. 

 

366

http://xueshu.baidu.com/s?wd=author%3A%28Wong%20Wai%20Keong%29%20%3BSch.%20of%20Comput.%20Technol.%2C%20Sunway%20Univ.%20Coll.%2C%20Bandar%20Sunway%2C%20Malaysia%20%3B&tn=SE_baiduxueshu_c1gjeupa&ie=utf-8&sc_f_para=sc_hilight%3Dperson
http://xueshu.baidu.com/s?wd=author%3A%28Lim%20Tong%20Ming%29%20&tn=SE_baiduxueshu_c1gjeupa&ie=utf-8&sc_f_para=sc_hilight%3Dperson
http://xueshu.baidu.com/s?wd=author%3A%28Kim%2C%20Yong%20Ho%29%20&tn=SE_baiduxueshu_c1gjeupa&ie=utf-8&sc_f_para=sc_hilight%3Dperson
http://xueshu.baidu.com/s?wd=author%3A%28Ryu%2C%20Ki%20Seon%29%20&tn=SE_baiduxueshu_c1gjeupa&ie=utf-8&sc_f_para=sc_hilight%3Dperson
http://xueshu.baidu.com/s?wd=author%3A%28Kim%2C%20Jeong%20Ki%29%20&tn=SE_baiduxueshu_c1gjeupa&ie=utf-8&sc_f_para=sc_hilight%3Dperson