Microsoft Word - 476hernandez.docx CHEMICAL ENGINEERING TRANSACTIONS VOL. 43, 2015 A publication of The Italian Association of Chemical Engineering Online at www.aidic.it/cet Chief Editors: Sauro Pierucci, Jiří J. Klemeš Copyright © 2015, AIDIC Servizi S.r.l., ISBN 978-88-95608-34-1; ISSN 2283-9216 Determination of Enzyme (Cellulase from Trichoderma reesei) Kinetic Parameters in the Enzymatic Hydrolysis of H2SO4- Catalyzed Hydrothermally Pretreated Sugarcane Bagasse at High-Solids Loading Laura Plazas Tovar, Emília Savioli Lopes, Maria Regina Wolf Maciel, Rubens Maciel Filho School of Chemical Engineering, University of Campinas, UNICAMP, Zipcode 13083–852, Campinas–SP, Brazil lplazast@feq.unicamp.br Enzymatic kinetic studies of celulignin material obtained from acid-catalyzed hydrothermally pretreated sugarcane bagasse at high-solids loading (S / 25%), acid concentration (A) equal to 1.0; 2.0 and 3.0% w/v and pretreatment time (tP) equal to 30; 90 and 150 min were carried out using the synergistic action of cellulase from T. reesei and cellobiase from Aspergillus niger. The kinetic experiments were carried out at 50 oC, 150 rpm and 3 h with substrate (water insoluble solids after pretreatment - WIS) loading range between 30 gsubstrate/Lsol and 100 gsubstrate/Lsol, and mixed with cellulase (at 5.0; 15.0; 30.0 and 60.0 FPU cellulase/gsubstrate) and β-glucosidase (at 33.0 IU β-glucosidase/gsubstrate) enzymes. A Michaelis-Menten dependence on the cellulase from T. reesei concentration and substrate concentration plots were obtained based on experimental data. The rate constant, Km and maximum reaction rate attainable, Vmax were determined to characterize the cellulase-catalyzed reaction. Results showed that the cellulase from T. reesei behavior was highly specific for each WIS fraction obtained under a combination of [A-S-tP] where Vmax varies greatly as enzyme (cellulase) concentration rises. For example, Vmax values when considered a substrate obtained at [1.0% w/v - 25% - 30 min] and [3.0% w/v - 25% - 30 min] using 5.0 FPU cellulase/gsubstrate(WIS) and [1.0% w/v - 25% - 90 min] and [3.0% w/v - 25% - 90 min] using 60.0 FPU cellulase/gsubstrate(WIS) were 5.96±0.27 gGLC/LSOLh; 2.90±0.05 gGLC/LSOLh; 5.16±0.18 gGLC/LSOLh; 7.48±0.81 gGLC/Lh, respectively. Dependence on the Km of enzyme-catalyzed reaction exhibited a considerably variation with the substrate nature and the enzymatic kinetic conditions establishing that Km for the cellulase from T. reesei –substrate complex was between 54.81 gGLC/LSOL and 209.99 gGLC/LSOL. 1. Introduction The enzymatic hydrolysis is a heterogeneous reaction catalyzed by cellulases, distinguished by an insoluble substrate (cellulose) and a soluble catalyst (enzymes). The complete hydrolysis of the cellulose requires the combined action of multiple enzymes with different substrate specificities (Kumar et al., 2008), and offers the potential for a long term reduction in costs, since it is possible to attain high yields under less critical conditions of pressure, temperature and chemical attack (Canilha et al., 2011). Kinetic modeling of enzymatic saccharification results in a complex procedure comprising the kinetics of enzyme-catalyzed reactions: Michaelis-Menten kinetics, enzyme Inhibition and the enzyme-substrate interactions among others. Bansal et al. (2009) provides an overview of the models published in the open literature about enzymatic mechanism on cellulose hydrolysis. In their review are presented eighteen works about empirical models where the main predicted variables were: the glucose concentration, glucan to glucose DOI: 10.3303/CET1543096 Please cite this article as: Plazas Tovar L., Savioli Lopes E., Wolf Maciel M.R., Maciel Filho R., 2015, Determination of enzyme (cellulase from trichoderma reesei) kinetic parameters in the enzymatic hydrolysis of h2so4-catalyzed hydrothermally pretreated sugarcane bagasse at high- solids loading, Chemical Engineering Transactions, 43, 571-576 DOI: 10.3303/CET1543096 571 conversion and hydrolysis yield. On the other hand, they presented Adsorption and Michaelis – Menten based models clustered in five groups: Michaelis – Menten, Product inhibition, Quasi Steady State assumption, Adsorption based approach, BG –β-glucosidase). For the adsorption based approach to approximate the kinetic equations governing the enzymatic hydrolysis and analyzing the enzyme-substrate reactions, Philippidis and Hatzis (1997) and Philippidis et al. (1992), defined a mathematical model based on quality and concentration of the cellulosic-substrate; quality and concentration of the cellulase and β-glucosidase enzyme system and the mode of interaction between substrate and enzyme (Figure 1). [ ] { } [ ] [ ] [ ] [ ] [ ] * 1 1 * 2 2 2 exp 1,3 1 1 i i B G m G k C t r i B G K K k B r G K B K λ− = = + + =   + +    Cellulose [C] Cellobiose [B] Glucose [G] r1 r2r3 where: [C], [B] and [G]: are the concentrations (g/L) of cellulose, cellobiose, glucose K1B, K1G and K2G: are inhibition constants (g/L) k1 *, k2* and k3 * : are the lumped specific rate constants for cellulose (h-1) and cellobiose (g/L h) hydrolysis λ: s the rate of decrease in the specific surface area of cellulose (h-1) Rate constants of the heterogeneous cellulose hydrolysis [ ] [ ] * i i eq k enzyme k K enzyme = + where: ki: are the maximum specific cellulose hydrolysis rates (h-1) [enzyme]: concentration of the cellulase and β-glucosidase enzyme complex (FPU/gsubstrate or IU /gsubstrate, respectively) Keq: is the cellulase enzyme saturation constant (g/L) Michaelis-Menten dependence on the cellulase concentration [ ]( )*2 2 1 Lk k enzimeg K L= − where: k2: is the specific cellobiose hydrolysis rate (g/IU h) [enzymeg]: concentration of the β-glucosidase enzyme complex (IU /gsubstrate) KL: is the β-glucosidase adsorption constant to lignin (L/g) L: is the lignin concentration (g/L) Homogeneous cellobiose hydrolysis Figure 1: Philippidis based kinetic model: adsorption of cellulose and β-glucosidase onto lignin Moreover, aiming to determine lumped specific rate constants for cellulose using the Philippidis and Hatzis (1997) and Philippidis et al. (1992) model associated to a Michaelis-Menten dependence on the cellulose, Kumar et al. (2008) described a methodology to ensure the validity of the steady state assumption for a standard enzyme-substrate reaction. In this sense, based on Philippidis and Hatzis (1997) and Philippidis et al. (1992) model to describe the enzymatic hydrolysis from lignocellulosic biomass, the present manuscript is an attempt to analyze the kinetic activator constant (Km) and maximum reaction rate attainable or theoretical maximal velocity, Vmax based on enzymatic kinetic investigation of celulignin material from H2SO4-catalyzed hydrothermally pretreated sugarcane bagasse at high-solids loading (S / 25%), acid concentration (A) equal to 1.0; 2.0 and 3.0% w/v and pretreatment time (tP) equal to 30; 90 and 150 min. For such an enzymatic complex of cellulase from T. reesei and cellobiase from Aspergillus niger was used. 2. Material and methods Sugarcane bagasse (SCB) was donated by a Brazilian sugar-alcohol-co-generation mill (Usina São João, Araras, São Paulo - Brazil) and its composition is presented in Figure 2. 572 H2SO4-catalyzed hydrothermal pre-treatment and enzymatic digestibility experiments were carried out as exhibited in Figure 2. Water insoluble solids (WIS) and liquid streams were analyzed based on standard procedures (Canilha et al., 2011, Gouveia et al., 2009, Sluiter et al., 2008). --------------------------- 41.81 ± 3.31 g Cellulose 31.00 ± 2.54 g Hemicellulose 17.08 ± 2.19 g Total Lignin 8.93 ± 1.16 g Extractives 2.53 ± 0.13 g Ash --------------------------- Enzymatic hydrolysate Acid hydrolysate WIS(EH) Cellulase, from Trichoderma reesei ATCC 26921 Cellobiase from Aspergillus niger Novozyme 188 (50 o C); (0 - 3 h) 5.0; 15.0; 30.0; 60.0 FPU/g substrate (WIS) ; 33.0 IU/g substrate (WIS) Hydrolysis WIS Pretreatment Biomass: SCB H 2 SO 4 solution: 1.0% w/v - 3.0% w/v S=25% (121 o C) (30, 90 and 150 min) H 2 SO 4 pretreatment Enzymatic hydrolysis The solid fraction was washed over a 400 mesh wire sieve with warm water at 60 °C to raise the pH to ~6 and prepared to enzymatic digestibility loading range between 30 g/L and 100 g/L Figure 2: Enzymatic kinetic studies of celulignin material obtained from acid-catalyzed hydrothermally pretreated sugarcane bagasse 2.1 Method of modelling: Michaelis-Menten kinetics The Michaelis-Menten (MM) equation is the model of enzyme kinetics for a one-substrate (S) enzyme- catalyzed (E) reaction to product (P) which quantitatively relates the initial rate, the maximum rate, and the initial substrate concentration to the Michaelis constant Km (Figure 3). Furthermore, enzyme-catalyzed reaction is characterized by the formation of a complex between the enzyme and its substrate (ES) (Berg et al., 2002). 1 2 1 2 k k k k S E ES E P − − ⎯⎯→ ⎯⎯→+ +←⎯⎯ ←⎯⎯The MM equation Consideration 1 Consideration 2 Only consider initial time:  [P] is neglected  Formation products reaction is irreversible 1 2 1 k k k S E ES E P − ⎯⎯→+ ⎯⎯→ +←⎯⎯ Then: oInitial rate v0=k2[ES] o[Etotal]=[E]+[ES] oRate formation of ES=k1[S]([E]total-[ES]) oRate of breakdown of ES=k-1[ES]+k2[ES] Rate of ES formation = Rate of ES breakdown Where: k1[S]([E]total-[ES])=k-1[ES]+k2[ES] [ ] [ ][ ] [ ] 1 2 1 total S E ES k k s k − =  + +     oInitial rate v0=k2[ES] [ ][ ] [ ] 0 2 1 2 1 total S E v k k k s k − =  + +     Consideration 3  [S] >> [E] total [ES] = [E] total As the concentration of substrate increases, the enzyme becomes saturated with substrate. [ ]max 2 totalV k E= [ ] [ ] max 0 1 2 1 S V v k k s k − =  + +     [ ] [ ] max 0 m S V v s K = + Figure 3: Considerations to use the Michaelis-Menten equation to estimate Philippidis and Hatzis (1997) and Philippidis et al. (1992) model parameters Based on Michaelis-Menten equation, it is possible to estimate k1*, k2* and k3* (Figure 1) and described the kinetic behavior of enzyme by Eq(1) considering a variation in solid substrate at different soluble enzyme concentration (Carvalho et al., 2013, Magalhães et al., 2010). [ ] [ ] max 0 m V S v K S = + (1) where: Vmax is the maximal velocity for the initial concentration of adsorption sites on the substrate (gGLC/LSOLh); Km is the corresponding half-saturation constant (gGLC/LSOL), and [S] is the substrate concentration (gsubstrate/L). 573 3. Results and discussion 3.1 Estimation of kinetic parameters for cellulase The initial rate of the glucose released from cellulose presented in the H2SO4-catalyzed hydrothermally pretreated sugarcane bagasse (under a combination of [A-S-tP] equal to [1.0% w/v - 25% - 90 min]; [2.0% w/v - 25% - 90 min] and [3.0% w/v - 25% - 90 min]) by the synergistic action of cellulase from T. reesei and cellobiase from Aspergillus niger as a function of substrate concentration is shown in Figure 4. Experimental data showed the effect of the H2SO4-catalyzed hydrothermal pretreatment of sugarcane bagasse, the substrate concentration and the enzyme concentration on the initial enzymatic hydrolysis during 3 h (Figure 4). Due to polymeric nature, it is observed that it is not a linear behavior and it rises as the substrate concentration and enzyme concentration increase up to substrate become limiting (about 80 gsubstrate/LSOL). 20 40 60 80 100 At A=2.0% w/v [E]=5 FPU/g substrate [E]=15 FPU/g substrate [E]=30 FPU/g substrate [E]=60 FPU/g substrate S/ g substrate /L sol 20 40 60 80 100 At A=3.0% w/v S/ g substrate /L sol 20 40 60 80 100 0.8 1.6 2.4 3.2 4.0 4.8 At A=1.0% w/v V / g G L C / L s o l h S/ g substrate /L sol Figure 4: Initial rate of the glucose released from cellulose presented in the H2SO4-catalyzed hydrothermally pretreated sugarcane bagasse Initial rates were based on the quantification of glucose after 3 h of hydrolysis guarantying a linear region of the time curve. Table 1 lists the calculated Vmax and Km from the enzymatic hydrolysis data by nonlinear regression following the Eq(1). For high values of enzyme concentration (60.0 FPU/gsubstrate), the ratio substrate and solution (SOL) became limited and the initial rate asymptotically approaches to a maximum as being: 2.81±0.25 gGLC/LSOL h, 2.62± - gGLC/LSOL h and 4.51±0.59 gGLC/LSOL h, respectively. Similar trends were observed for the others substrates obtained from different pretreatment conditions. Comparing the hydrolysis of substrate pretreated at acid concentration equal to 1.0, 2.0 and 3.0% w/v at the same cellulase enzyme concentration, it is observed that acid concentration in the pretreatment increases the total sugar (glucose) yield on the saccharification process about two times when acid concentration rises from 1.0 to 3.0% w/v. Moreover, results evidenced that increasing enzyme (from 5.0 to 60.0 FPU/gsubstrate), it is produced higher amount of soluble reducing sugars, although for enzyme concentration between 15.0 and 30.0 FPU/gsubstrate, for H2SO4-catalyzed hydrothermally pretreated sugarcane bagasse at 1.0% w/v, small differences were observed because of the substrate saturation. Kinetics parameters were determined using Eq(1). A maximum rate, Vmax values, when considered a substrate obtained at [1.0% w/v - 25% - 30 min] and [3.0% w/v - 25% - 30 min] using 5.0 FPU cellulase/gsubstrate(WIS) and [1.0% w/v - 25% - 90 min] and [3.0% w/v - 25% - 90 min] using 60.0 FPU cellulase/gsubstrate(WIS) were 5.96±0.27 gGLC/LSOLh; 2.90±0.05 gGLC/LSOLh; 5.16±0.18 gGLC/LSOLh; 7.48±0.81 gGLC/LSOLh, respectively. Initial rate of enzymatic hydrolysis were calculated from the MM model and compared with the experimental results (Figure 4) and the MM model fits well with the experimental results reporting a adjustable-R2 higher than 0.93. 574 575 Carvalho et al. (2013) studied the influence of substrate concentration for the exploded sugarcane bagasse treated with 4% NaOH during the enzymatic hydrolysis. Analyses during enzymatic hydrolysis were carried out for substrate loads ranges between 11.11 gsubstrate/LSOL and 111.11 gsubstrate/LSOL. Results reported a Vmax = 6.3 gGLC/LSOLh and Km = 8.78 gGLC/LSOL. Thus, the dependence on the Km of enzyme-catalyzed reaction exhibited a considerably variation with the substrate nature and the enzymatic kinetic conditions establishing that Km for the cellulase from T. reesei – substrate complex was between 54.81 gGLC/LSOL and 209.99 gGLC/LSOL. Higher Km values indicate that the cellulase from T. reesei binds the substrate weakly and due to wide variation in Km, it could be an indication of the presence of an inhibitor and/or loss of enzyme activity through adsorption to the lignin present in the substrate. 4. Conclusions The influence of enzyme concentration (between 5.0 and 60.0 FPU/gsubstrate) and substrate concentration (between 30 and 100 gsubstrate/LSOL) on the production of glucose was studied by the Michaelis–Menten model showing good correlation with experimental data. The parameters Vmax and Km have been determined with high accuracy. Acknowledgements The authors gratefully acknowledge the financial support provided by São Paulo Research Foundation- FAPESP (Grant N°. 2012/10857-3 and 2008/57873-8). References Bansal P., Hall M., Realff M.J., Lee J.H., Bommarius A.S., 2009, Modeling cellulase kinetics on lignocellulosic substrates. Biotechnol. Adv., 27, 833-848. Berg J.M., Tymoczko J.L., Stryer L., 2002, Section 8.4, The Michaelis-Menten Model Accounts for the Kinetic Properties of Many Enzymes < http://www.ncbi.nlm.nih.gov/books/NBK22430/>: W H Freeman. accessed December 1 2014. Canilha L., Santos V.O., Rocha G.M., Almeida E Silva J., Giulietti M., Silva S., Felipe M.A., Ferraz A., Milagres A.F., Carvalho W., 2011, A study on the pretreatment of a sugarcane bagasse sample with dilute sulfuric acid. J. Ind. Microbiol. Biotechnol., 38, 1467-1475. Carvalho M.L., Sousa Jr. R., Rodríguez-Zúñiga U.F., Suarez C.a.G., Rodrigues D.S., Giordano R.C., Giordano R.L.C., 2013, Kinetic study of the enzymatic hydrolysis of sugarcane bagasse. Braz. J. Chem. Eng., 30, 437-447. Gouveia E.R., Nascimento R.T.D., Souto-Maior A.M., Rocha G.J.D.M., 2009, Validação de metodologia para a caracterização química de bagaço de cana-de-açúcar. Quim. Nova, 32, 1500-1503. Kumar R., Singh S., Singh O., 2008, Bioconversion of lignocellulosic biomass: biochemical and molecular perspectives. J. Ind. Microbiol. Biotechnol., 35, 377-391. Magalhães S.P., Falcão P.W.C., Nogueira S.C., Pessoa F.L.P., 2010, The synthesis of biodiesel via enzymatic ethanolysis of the sunflower and palm oils: kinetic modeling. Chemical Engineering Transaction, 20, 37-42. Philippidis G.P., Hatzis C., 1997, Biochemical engineering analysis of critical process factors in the biomass- to-ethanol technology. Biotechnol. Prog., 13, 222-231. Philippidis G.P., Spindler D.D., Wyman C.E., 1992, Mathematical modeling of cellulose conversion to ethanol by the simultaneous saccharification and fermentation process. Appl. Biochem. Biotechnol., 34-35, 543- 556. Sluiter A., Hames B., Ruiz R., Scarlata C., Sluiter J., Templeton D., Crocker D. 2008. Determination of structural carbohydrates and lignin in biomass - NREL/TP-510-42618. Laboratory Analytical Procedure (LAP). Revised August 2012 ed.: National Renewable Energy Laboratory. 576