Edelweiss Applied Science and Technology ISSN: 2576-8484 Vol. 2, No. 1, 184-186 2018 DOI: 10.33805/2576-8484.136 © 2018 by the author © 2018 by the author History: Received: 15 February 2018; Accepted: 22 February 2018; Published: 26 February 2018 How Can the Nanomaterial Surfaces Be Highly Cleaned? Viet Phuong Pham1,2 1SKKU Advanced Institute of Nano Technology (SAINT), Sungkyunkwan University (SKKU), Suwon, Republic of Korea; pvphuong85@ibs.re.kr (V.P.P.). 2Center for Multidimensional Carbon Materials, Institute for Basic Science, 44919, Ulsan, Republic of Korea. 1. Introduction The induced contaminations (e.g polymer residues or impurities in air) on nanomaterial surfaces have been a serious problem to probe their intrinsic properties and for unique applications in surface chemistry, electronic, and optoelectronic. The polymer residues still presented on chemical vapor deposited graphene surface after its wet transfer (e.g. poly(methyl methacrylate) (PMMA)) on the arbitrary substrates tends to cause problems such as electrical degradation and unwanted intentional doping. Polymer residues (e.g PMMA), defects, and other contaminations are commonly leaving the thin layers or the particles as residues on nanomaterials. Nowadays, the nanomaterials are receiving broad interests. Among them, grapheme [1-36], hexagonal-boron nitride (h- BN) [37-40], carbon nanotubes (CNTs) [41,42], and graphene oxide [43] are emerging as many promising potential materials with novel properties in electronics and optoelectronics (Figure 1). These nanomaterials have attracted a huge research interest in recent decades due to its anomalous properties such as very high carrier mobility, extremely high mechanical strength and optical transparency, electrical conductivity, chemical stability and thermal conductivity [1-43] and that is the reason above nanomaterials are being observed as a potential material for next-generation semiconductor devices that would replace silicon-based technology. Due to being an atomically thin material, every atom of nanomaterials has an access to surface that is directly responsible for its electronic and chemical activity. However, for many applications, the nanomaterials in pristine form cannot be used due to high resistance and performance degradation on poor nanomaterial quality. Thereby, the exploration of new methods in order to mitigation as much polymer residues as possible on nanomaterials (CVD Graphene, CNT, GO, h-BN) is highly desirable (Figure 2). For instance on CVD graphene material, many reports have demonstrated to remove poly(methyl methacrylate) (PMMA) residues and other impurities on surface achieved the significant achievements such as wet chemical by acetone [25,26], cleaning by chloroform or toluene [44] by N-methyl-2-pyrrolidone [45] by diazonium salt [46] a modified RCA cleaning process and mechanically sweeping away the contamination [47] oxygen plasma and reactive ion etching treatment for a short time [25,26,46] mechanical method: AFM tip can remove all resist (theoretically without damaging the sample) in a contact mode [34] annealing in high temperature [18,25,26,48] current annealing [49] by acetic acid [50] by electrostatic force [16] by lithography resist [17] by annealing [18] by electric current [19] by electrolytic [20] by titanium sacrificial layer [22] by heat treatment in air and vacuum [23] by dry-cleaning [24]. Very recently, a superior technique for cleaning of nanomaterials using plasma (Ar, oxygen) proved extremely efficient in residue cleaning from graphene surface and tuning the graphene properties [25-29,51]. Figure 1. Schematic of cleaning of various nanomaterial surfaces (CVD graphene, CNTs, GO, h-BN) by chemistry, physic, nanotechnology, and engineering for tuning their electronics and optoelectronics. The cleaning of CNT materials surface by cyclic Ar plasma and nitric acid treatment for enhancing the electrical conductivity of flexible transparent conducting film [41] or by RF-PECVD technique [42] has also well-investigated. Or the surface of the h-BN material was cleaned greatly by wet chemical (HF solution) and annealing in vacuum at 10500C [52] or annealing at 4500C in air and ozone [40]. In addition, the contamination on GO surface was removed significantly assisted by an oxidation process and washing-centrifugation cycles which is controlled by pH of the supernatant. mailto:pvphuong85@ibs.re.kr 185 Edelweiss Applied Science and Technology ISSN: 2576-8484 Vol. 2, No. 1: 184-186, 2018 DOI: 10.33805/2576-8484.136 © 2018 by the author Figure 2. Cleaning process of various nanomaterial surfaces such as carbon nanotubes (a- c), graphene (d-e), h-BN (f,g), and GO (i,j). (a-c) reproduced with permission from [41]. (d,e) reproduced with permission from [17]. (f,g) reproduced with permission from [40]. (i,j) reproduced with permission from [43]. The cleaning of nanomaterials (CVD Graphene, CNT, h-BN, GO) using various strategies related to chemistry, physic, nanotechnology, and engineering in order to obtain the ultra-clean material layer and resulting in improving their electrical characteristics is highly desiring with targeting toward practical applications in the industry to serve human society. The enhancing of electrical properties of cleaned nanomaterials would be raising up the current on-off ratio, photoluminescence, and other unexploited and unexplored exotic properties. Consequently, it could unlock and take a leap forward on developing superior plasma-based cleaning methods [15,32] for other TMDs and low-dimensional materials in various advanced devices and applications. References [1] K. S. Novoselov et al., "Electric field effect in atomically thin Carbon films," Science, vol. 306, no. 5696, pp. 666-669, 2004. https://doi.org/10.1126/science.1102896 [2] V. P. Pham, H.-S. Jang, D. Whang, and J.-Y. Choi, "Direct growth of graphene on rigid and flexible substrates: Progress, applications, and challenges," Chemical Society Reviews, vol. 46, no. 20, pp. 6276-6300, 2017. https://doi.org/10.1039/c7cs00224f [3] V. P. Pham et al., "Chlorine-trapped CVD bilayer graphene for resistive pressure sensor with high detection limit and high sensitivity," 2D Materials, vol. 4, no. 2, p. 025049, 2017. https://doi.org/10.1088/2053-1583/aa6390 [4] V. P. Pham, K. N. Kim, M. H. Jeon, K. S. Kim, and G. Y. Yeom, "Cyclic chlorine trap-doping for transparent, conductive, thermally stable and damage-free graphene," Nanoscale, vol. 6, no. 24, pp. 15301-15308, 2014. https://doi.org/10.1039/c4nr04387a [5] V. P. Pham, K. H. Kim, M. H. Jeon, S. H. Lee, K. N. Kim, and G. Y. Yeom, "Low damage pre-doping on CVD graphene/Cu using a chlorine inductively coupled plasma," Carbon, vol. 95, pp. 664-671, 2015. https://doi.org/10.1016/j.carbon.2015.08.070 [6] V. P. Pham, A. Mishra, and G. Y. Yeom, "The enhancement of Hall mobility and conductivity of CVD graphene through radical doping and vacuum annealing," RSC advances, vol. 7, no. 26, pp. 16104-16108, 2017. https://doi.org/10.1039/c7ra01330b [7] V. P. Pham et al., "Low energy BCl3 plasma doping of few-layer graphene," Science of Advanced Materials, vol. 8, no. 4, pp. 884-890, 2016. https://doi.org/10.1166/sam.2016.2549 [8] V. Pham, "Chemical vapor deposited graphene synthesis with same-oriented hexagonal domains," Eng Press, vol. 1, pp. 39-42, 2018. [9] K. N. Kim, V. P. Pham, and G. Y. Yeom, "Chlorine radical doping of a few layer graphene with low damage," ECS Journal of Solid State Science and Technology , vol. 4, no. 6, p. N5095, 2015. https://doi.org/10.1149/2.0141506jss [10] V. P. Pham and G. Y. Yeom, "Recent advances in doping of molybdenum disulfide: Industrial applications and future prospects," Advanced Materials, vol. 28, no. 41, pp. 9024-9059, 2016. https://doi.org/10.1002/chin.201651225 [11] A. Ferrari, F. Bonaccorso, and V. Fal'ko, "Science and technology roadmap for graphene, related two-dimensional crystals, and hybrid systems," Nanoscale, vol. 7, pp. 4587-5062, 2015. [12] S. Z. Butler et al., "Progress, challenges, and opportunities in two-dimensional materials beyond graphene," ACS Nano, vol. 7, no. 4, pp. 2898-2926, 2013. [13] A. K. Geim and K. S. Novoselov, "The rise of graphene," Nature Materials, vol. 6, no. 3, pp. 183-191, 2007. [14] H. Zhang, P. Yang, and M. Prato, "Grand challenges for nanoscience and nanotechnology," ACS Nano, vol. 9, pp. 6637-6640, 2015. [15] K. S. Kim et al., "Atomic layer etching of graphene through controlled ion beam for graphene-based electronics," Scientific Reports, vol. 7, no. 1, p. 2462, 2017. https://doi.org/10.1038/s41598-017-02430-8 [16] W. J. Choi et al., "A simple method for cleaning graphene surfaces with an electrostatic force," Advanced Materials, vol. 26, no. 4, pp. 637-644, 2014. https://doi.org/10.1002/adma.201303199 [17] M. Ishigami, J.-H. Chen, W. G. Cullen, M. S. Fuhrer, and E. D. Williams, "Atomic structure of graphene on SiO2," Nano Letters, vol. 7, no. 6, pp. 1643-1648, 2007. [18] Y.-C. Lin, C.-C. Lu, C.-H. Yeh, C. Jin, K. Suenaga, and P.-W. Chiu, "Graphene annealing: How clean can it be?," Nano Letters, vol. 12, no. 1, pp. 414-419, 2012. https://doi.org/10.1021/nl203733r [19] J. Moser, A. Barreiro, and A. Bachtold, "Current-induced cleaning of graphene," Applied Physics Letters, vol. 91, no. 16, p. 161513, 2007. [20] J. Sun, H. O. Finklea, and Y. Liu, "Characterization and electrolytic cleaning of poly (methyl methacrylate) residues on transferred chemical vapor deposited graphene," Nanotechnology, vol. 28, no. 12, p. 125703, 2017. https://doi.org/10.1088/1361-6528/aa5e55 [21] J. D. Wood et al., "Annealing free, clean graphene transfer using alternative polymer scaffolds," Nanotechnology, vol. 26, no. 5, p. 055302, 2015. https://doi.org/10.1088/0957-4484/26/5/055302 https://doi.org/10.1126/science.1102896 https://doi.org/10.1039/c7cs00224f https://doi.org/10.1088/2053-1583/aa6390 https://doi.org/10.1039/c4nr04387a https://doi.org/10.1016/j.carbon.2015.08.070 https://doi.org/10.1039/c7ra01330b https://doi.org/10.1166/sam.2016.2549 https://doi.org/10.1149/2.0141506jss https://doi.org/10.1002/chin.201651225 https://doi.org/10.1038/s41598-017-02430-8 https://doi.org/10.1002/adma.201303199 https://doi.org/10.1021/nl203733r https://doi.org/10.1088/1361-6528/aa5e55 https://doi.org/10.1088/0957-4484/26/5/055302 186 Edelweiss Applied Science and Technology ISSN: 2576-8484 Vol. 2, No. 1: 184-186, 2018 DOI: 10.33805/2576-8484.136 © 2018 by the author [22] C. A. Joiner, T. Roy, Z. R. Hesabi, B. Chakrabarti, and E. M. Vogel, "Cleaning graphene with a titanium sacrificial layer," Applied Physics Letters, vol. 104, no. 22, p. 223109, 2014. https://doi.org/10.1063/1.4881886 [23] M. Tripathi et al., "Cleaning graphene: Comparing heat treatments in air and in vacuum," Physica Status Solidi (RRL)– Rapid Research Letters, vol. 11, no. 8, p. 1700124, 2017. https://doi.org/10.1002/pssr.201700124 [24] G. Siller-Algara, O. Lehtinen, A. Turchanin, and U. Kaiser, "Dry-cleaning of graphene," Applied Physics Letters, vol. 104, no. 15, p. 153115, 2014. [25] N. Peltekis, S. Kumar, N. McEvoy, K. Lee, A. Weidlich, and G. S. Duesberg, "The effect of downstream plasma treatments on graphene surfaces," Carbon, vol. 50, no. 2, pp. 395-403, 2012. https://doi.org/10.1016/j.carbon.2011.08.052 [26] N. McEvoy, H. Nolan, N. A. Kumar, T. Hallam, and G. S. Duesberg, "Functionalisation of graphene surfaces with downstream plasma treatments," Carbon, vol. 54, pp. 283-290, 2013. https://doi.org/10.1016/j.carbon.2012.11.040 [27] V. Prudkovskiy, K. Katin, M. Maslov, P. Puech, R. Yakimova, and G. Deligeorgis, "Efficient cleaning of graphene from residual lithographic polymers by ozone treatment," Carbon, vol. 109, pp. 221-226, 2016. https://doi.org/10.1016/j.carbon.2016.08.013 [28] F. Hadish, S. Jou, B.-R. Huang, H.-A. Kuo, and C.-W. Tu, "Functionalization of CVD grown graphene with downstream oxygen plasma treatment for glucose sensors," Journal of The Electrochemical Society , vol. 164, no. 7, p. B336, 2017. https://doi.org/10.1149/2.0601707jes [29] H. Al-Mumen, F. Rao, W. Li, and L. Dong, "Singular sheet etching of graphene with oxygen plasma," Nano-Micro Letters, vol. 6, pp. 116-124, 2014. https://doi.org/10.1007/bf03353775 [30] H. Sun et al., "High quality graphene films with a clean surface prepared by an UV/ozone assisted transfer process," Journal of Materials Chemistry C, vol. 5, no. 8, pp. 1880-1884, 2017. [31] W. Choi, M. A. Shehzad, S. Park, and Y. Seo, "Influence of removing PMMA residues on surface of CVD graphene using a contact-mode atomic force microscope," RSC Advances, vol. 7, no. 12, pp. 6943-6949, 2017. https://doi.org/10.1039/c6ra27436f [32] K. S. Kim et al., "Surface treatment process applicable to next generation graphene-based electronics," Carbon, vol. 104, pp. 119-124, 2016. https://doi.org/10.1016/j.carbon.2016.03.054 [33] Y. Jia et al., "Toward high carrier mobility and low contact resistance: Laser cleaning of PMMA residues on graphene surfaces," Nano-Micro Letters, vol. 8, pp. 336-346, 2016. https://doi.org/10.1007/s40820-016-0093-5 [34] A. Goossens, V. Calado, A. Barreiro, K. Watanabe, T. Taniguchi, and L. Vandersypen, "Mechanical cleaning of graphene," Applied Physics Letters, vol. 100, no. 7, p. 073110, 2012. https://doi.org/10.1063/1.3685504 [35] H. M. Choi, J. A. Kim, Y. J. Cho, T. Y. Hwang, J. W. Lee, and T. S. Kim, "Surface cleaning of graphene by CO2 cluster," Solid State Phenomena, vol. 219, pp. 68-70, 2014. [36] K. Kumar, Y.-S. Kim, and E.-H. Yang, "The influence of thermal annealing to remove polymeric residue on the electronic doping and morphological characteristics of graphene," Carbon, vol. 65, pp. 35-45, 2013. https://doi.org/10.1016/j.carbon.2013.07.088 [37] C. R. Dean et al., "Boron nitride substrates for high-quality graphene electronics," Nature Manotechnology, vol. 5, no. 10, pp. 722-726, 2010. [38] C. Elbadawi et al., "Electron beam directed etching of hexagonal boron nitride," Nanoscale, vol. 8, no. 36, pp. 16182- 16186, 2016. https://doi.org/10.1039/c6nr04959a [39] Y. Liao et al., "Oxidative etching of hexagonal boron nitride toward nanosheets with defined edges and holes," Scientific Reports, vol. 5, no. 1, p. 14510, 2015. https://doi.org/10.1038/srep14510 [40] S. J. Cartamil-Bueno, M. Cavalieri, R. Wang, S. Houri, S. Hofmann, and H. S. van der Zant, "Mechanical characterization and cleaning of CVD single-layer h-BN resonators," npj 2D Materials and Applications, vol. 1, no. 1, p. 16, 2017. https://doi.org/10.1038/s41699-017-0020-8 [41] V. P. Pham et al., "Effect of plasma–nitric acid treatment on the electrical conductivity of flexible transparent conductive films," Japanese Journal of Applied Physics, vol. 52, no. 7R, p. 075102, 2013. https://doi.org/10.7567/jjap.52.075102 [42] H. Di, M. Li, H. Li, B. Huang, and B. Yang, "Purification and characterization of carbon nanotubes synthesized by RF-PECVD," ECS Transactions, vol. 44, no. 1, pp. 499-504, 2012. https://doi.org/10.1149/1.3694360 [43] I. Barbolina, C. Woods, N. Lozano, K. Kostarelos, K. Novoselov, and I. Roberts, "Purity of graphene oxide determines its antibacterial activity," 2D Materials, vol. 3, no. 2, p. 025025, 2016. https://doi.org/10.1088/2053- 1583/3/2/025025 [44] N. Patra, M. Salerno, A. Diaspro, and A. Athanassiou, "Effect of solvents on the dynamic viscoelastic behavior of poly (methyl methacrylate) film prepared by solvent casting," Journal of Materials Science, vol. 46, pp. 5044-5049, 2011. [45] X. Liang et al., "Toward clean and crackless transfer of graphene," ACS Nano, vol. 5, no. 11, pp. 9144-9153, 2011. https://doi.org/10.1021/nn203377t [46] X.-Y. Fan, R. Nouchi, L.-C. Yin, and K. Tanigaki, "Effects of electron-transfer chemical modification on the electrical characteristics of graphene," Nanotechnology, vol. 21, no. 47, p. 475208, 2010. https://doi.org/10.1088/0957- 4484/21/47/475208 [47] C. Y. Stephen, P. R. Krauss, and P. J. Renstrom, "Nanoimprint lithography," Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena , vol. 14, no. 6, pp. 4129-4133, 1996. [48] L. S. Wei, C. T. Nai, and J. T. Thong, "What does annealing do to metal–graphene contacts?," Nano Letters, vol. 14, no. 7, pp. 3840-3847, 2014. https://doi.org/10.1021/nl500999r [49] H. Michael, R. Beams, and L. Novotny, "Graphene transfer with reduced residue," Physics Letters A, vol. 377, no. 21- 22, pp. 1455-1458, 2013. https://doi.org/10.1016/j.physleta.2013.04.015 [50] Y.-D. Lim, D.-Y. Lee, T.-Z. Shen, C.-H. Ra, J.-Y. Choi, and W. J. Yoo, "Si-compatible cleaning process for graphene using low-density inductively coupled plasma," ACS Nano, vol. 6, no. 5, pp. 4410-4417, 2012. https://doi.org/10.1021/nn301093h [51] S. W. King, R. J. Nemanich, and R. F. Davis, "Cleaning of pyrolytic hexagonal boron nitride surfaces," Surface and Interface Analysis, vol. 47, no. 7, pp. 798-803, 2015. https://doi.org/10.1002/sia.5781 https://doi.org/10.1063/1.4881886 https://doi.org/10.1002/pssr.201700124 https://doi.org/10.1016/j.carbon.2011.08.052 https://doi.org/10.1016/j.carbon.2012.11.040 https://doi.org/10.1016/j.carbon.2016.08.013 https://doi.org/10.1149/2.0601707jes https://doi.org/10.1007/bf03353775 https://doi.org/10.1039/c6ra27436f https://doi.org/10.1016/j.carbon.2016.03.054 https://doi.org/10.1007/s40820-016-0093-5 https://doi.org/10.1063/1.3685504 https://doi.org/10.1016/j.carbon.2013.07.088 https://doi.org/10.1039/c6nr04959a https://doi.org/10.1038/srep14510 https://doi.org/10.1038/s41699-017-0020-8 https://doi.org/10.7567/jjap.52.075102 https://doi.org/10.1149/1.3694360 https://doi.org/10.1088/2053-1583/3/2/025025 https://doi.org/10.1088/2053-1583/3/2/025025 https://doi.org/10.1021/nn203377t https://doi.org/10.1088/0957-4484/21/47/475208 https://doi.org/10.1088/0957-4484/21/47/475208 https://doi.org/10.1021/nl500999r https://doi.org/10.1016/j.physleta.2013.04.015 https://doi.org/10.1021/nn301093h https://doi.org/10.1002/sia.5781