Microsoft Word - 9-2242_s6 Engineering, Technology & Applied Science Research Vol. 8, No. 5, 2018, 3350-3354 3350 www.etasr.com Jayaswal & Palwalia: Performance Analysis of Non-Isolated DC-DC Buck Converter Using Resonant … Performance Analysis of Non-Isolated DC-DC Buck Converter Using Resonant Approach Kuldeep Jayaswal Department of Electrical Engineering Rajasthan Technical University Kota, India kuldeep12555@gmail.com Dheeraj Kumar Palwalia Department of Electrical Engineering Rajasthan Technical University Kota, India dheerajpalwalia@gmail.com Abstract—DC-DC converters preserve or control the output DC voltage. Due to parasitic constituents such as leakage capacitance of both diode and inductor, and transformer leakage inductance, DC-DC converters mostly operate on rigid switching conditions which result in high switching losses. These parasitic constituents affect the dc-dc converter’s operational reliability, instigate electromagnetic interference issues and limit the converter’s operation at higher frequency operations. In this paper, resonant or soft-switch approach has been employed to improve the operating performance and design-oriented principle investigations have been carried out for overcoming the issues of parasitic constituents in 24-12V DC-DC step-down (buck) converter. This paper divulges the analysis and Matlab Simulation results for 24-12V buck converter based on resonant or soft-switching approach. Keywords—operational reliability; DC-DC converter; resonant converter; Matlab simulation; step-down converter I. INTRODUCTION DC-DC conversion technologies are an important subject of research in the power engineering and drives area. These devices are electronic platforms used to customize DC electric voltage efficiently [1]. These converters are mostly used for changing the different voltage level [2-5]. Mainstream PWM converters do not work on soft-switch approach, they mostly operate on hard switching conditions. Semiconductor devices suffer from switching losses and electro-magnetic interference problems during switching-on and off which results in poor converter performance [5-6]. There are various factors which are accountable of switching loss like capacitance of both diode and switch [7-11]. This paper shows the soft- switch/resonant approach based on null voltage switching operation for reduction of all uncertainties related to customary DC-DC buck converter. II. NON-ISOLATED DC-DC CONVERTER TOPOLOGIES AND RESONANT/SOFT-SWITCH APPROACH A. The Concept Behind the Requirment of Resonant Approach DC-DC semiconductor devices like BJT, MOSFET or IGBT work as a switch at required frequency (f) [12]. The elementary circuit topologies of non-isolated dc-dc converters are shown in Figure 1 [13-19]. The voltage and current waveforms of the switch may have different shapes. As the voltage and current across the switch are not zero during switching times, there will be switching losses. Due to this, the switching frequency is bounded in pulse-width modulating converters. If the frequency is increased, then high electromagnetic interference problems will occur [2]. High stress will be on device during switching times due to high spikes in switch voltage and current. That’s why such a switching results to low switching losses. Fig. 1. Non-isolated DC-DC converter topologies without resonant/soft- switch approach In this paper, the buck non-isolated topology has been used as a principal platform to revamp performance and operational reliability of the converter. For this purpose, zero voltage switch operational approach has been used via appropriate placement of resonant switches. MOSFETs and IGBTs are mostly used as a switch in electronic conversions where at a particular time period they have to operate either in fully on or off condition. Being a current controlled device, MOSFETs are much faster in switching operation in comparison to BJT [8]. Thus, these devices are most eligible to work at higher switching frequencies. Engineering, Technology & Applied Science Research Vol. 8, No. 5, 2018, 3350-3354 3351 www.etasr.com Jayaswal & Palwalia: Performance Analysis of Non-Isolated DC-DC Buck Converter Using Resonant … B. Switch Configuration Concept for ZVS Approach Switching losses are related to the switching frequency fs, and these losses limit the maximum switching frequency. The energy reserved in output capacitance Co of switch just before the transistor turns on is given as ��� = ����� � 2⁄ (1) where ����=transistor voltage during off-instant. When the switch turns on, the energy imposed on the switch, causes transistor switching loss � �(���) = ����� �� 2⁄ (2) In this approach, a special switch configuration has been used which is made up with combinations of two different resonant elements with an anti-parallel diode. Figure 2 shows the switch configuration for resonant or smooth switching [14- 19]. Here a capacitor is coupled in counterpart with SW and resonant inductor in series. In this paper, resonant or zero voltage, switch operational approach has been used for the analysis of 24-12V DC-DC step-down converter. According to this when the switch is on, the voltage at the switch becomes zero, and that’s why the energy reserved in the output capacitance of switch is null during turn this time. Hence, the switching on losses becomes zero, which provides smooth efficient operation at high frequencies and results in the reduction in the amplitude of the converters. During this period, the above mentioned switch configuration plays a crucial role. In this, the resonant capacitor will resonate to null voltage before SW is turned-on. On the other hand, when the switch is turned-off, a little time is required to charge the resonant capacitor and hence the voltage over the SW is not increased abruptly. So, there is a very small overlapping between the SW current and voltage. So, the zero voltage switch operation is achieved. The main idea behind this approach is the fact that these soft-switch converter topologies absorb different parasitic components, like transformer’s leakage inductance, output capacitance of both transistor and diode. Figure 3, exhibits the proposed topology for non-isolated buck (step-down) converter based on resonant technique. Initially the switch remains in off situation during this instant current across switch is null but the voltage is not. Fig. 2. ZVS approach based on resonant switch configuration Fig. 3. Topology for non-isolated buck converter based on zero voltage switch/resonant approach During the switch-on, the voltage is forced to be zero and the current is a little-bit delayed so that it will start to lift after the zero voltage as shown in Figure 4(b). In zero current switch approach, a switch is off during zero current. The voltage through it might be zero but the current across the device is not. Voltage is granted to lift after current becomes zero as illustrated in Figure 4(c). Fig. 4. (a) Firm-switching converter incident, (b) zero or null Voltage switching case, (c) zero or null current switching case III. ANALYSIS OF DC-DC BUCK CONVERTER WITH AND WITHOUT SOFT SWITCH APPROACH Figure 5 shows the conventional buck or step-down converter without resonant or soft switch approach, which is a cheap electronic device used to obtain reduced voltage. Fig. 5. DC-DC buck converter topology without resonant or soft switch approach The switch operation is regulated by a modulator and turned-on and off at duty ratio “D” and at required switching frequency � = 1/�. Closed loop control has been used for stable operation: �� = ��� ⇒ ��� ∕ (��� + ����) = ���� (3) The operational strategy consists of two stages. At t=0, the switch is in ON state and the diode is in OFF state because VD =−VI. Further current across the inductor increases continuously due to voltage difference VL=VI–VO. At this time the current through the inductor and switch are both equal and energy is delivered to energy storage elements. In the second stage, at t=DT, the switch is in OFF state by gate driver, but during this time the inductor still has the previously stored current which turns the diode ON. During this instant, the voltage over the inductor is given as (–VO) and the voltage over the switch is given as (VI). That’s why IL decreases continuously with a slope of (–VO)/L. Input voltage is unplugged from the circuit and doesn’t transfer any energy to the storage elements. The average output voltage in the buck converter is given by (4), which does not depend on load [6]. �� ��⁄ = � ⇒ �� = ��� (4) The buck converter circuit based on the proposed approach is shown in Figure 8. Time Time Time (a) (b) (c) Power Loss Voltage Curve Voltage Curve Current Curve Current ZVS Switching Current ZCS Switching Conventional Conventional On Off Voltage Engineering, Technology & Applied Science Research Vol. 8, No. 5, 2018, 3350-3354 3352 www.etasr.com Jayaswal & Palwalia: Performance Analysis of Non-Isolated DC-DC Buck Converter Using Resonant … Fig. 6. Circuit state & waveform for time interval 0 65./?0�. Calculation of capacitor’s value > ?/650�. Max. voltage across switch � 2 (1 + !@AB ?⁄ ) IV. SIMULATION RESULTS A. Without Resonant/Soft-Switch Approach Fig. 9. Current across inductor Fig. 10. Output current of buck converter (current versus time) Fig. 11. Output voltage (12V) of buck converter (voltage versus time) Engineering, Technology & Applied Science Research Vol. 8, No. 5, 2018, 3350-3354 3353 www.etasr.com Jayaswal & Palwalia: Performance Analysis of Non-Isolated DC-DC Buck Converter Using Resonant … TABLE II. OPERATIONAL PROCESS FOR NON-ISOLATED DC-DC BUCK CONVERTER USING RESONANT OR SOFT-SWITCH APPROACH Time interval Circuit models/States Response/Behavior Waveforms 0