Microsoft Word - ETASR_V11_N1_pp6775-6780 Engineering, Technology & Applied Science Research Vol. 11, No. 1, 2021, 6775-6780 6775 www.etasr.com Nguyen et al.: Cutting Parameter Optimization in Finishing Milling of Ti-6Al-4V Titanium Alloy under … Cutting Parameter Optimization in Finishing Milling of Ti-6Al-4V Titanium Alloy under MQL Condition using TOPSIS and ANOVA Analysis Van Canh Nguyen Department of Manufacturing Technology Faculty of Mechanical Engineering Hanoi University of Industry Hanoi, Vietnam nguyenvancanh@haui.edu.vn Thuy Duong Nguyen Department of Machine Tool and Tribology School of Mechanical Engineering Hanoi University of Science and Technology Hanoi, Vietnam duong.nguyenthuy@hust.edu.vn Dung Hoang Tien Department of Manufacturing Technology Faculty of Mechanical Engineering Hanoi University of Industry Hanoi, Vietnam tiendung@haui.edu Abstract-Titanium and its alloys give immense specific strength, imparting properties such as corrosion and fracture resistance, making them the right candidate for medical and aerospace applications. There is a wide range of engineering applications that use titanium alloys in a variety of forms. The cost of these alloys is slightly higher in comparison to other variants due to the problematic extraction of the molten process. To reduce costs, titanium alloy products could be made by casting, isothermal forging, radial swaging, or powder metallurgy, although these techniques require some kind of finishing machining process. Titanium and its alloys are difficult to machine due to skinny chips leading to a small cutting tool-workpiece contact area. The thermal conductivity of titanium alloys is too low and the stress produced is too large due to the small contact area, which results in very high cutting temperatures. This paper deals with the experimental study of the influence of the Minimum Quantity Lubricant (MQL) environment in the milling of Ti-6Al-4V alloy considering the optimization of surface roughness and production rate. Taguchi-based TOPSIS and ANOVA were used to analyze the results. The experimental results show that MQL with vegetable oil is successfully applied in the milling of Ti-6Al-4V. The research confirms the suitability of TOPSIS in solving the Multiple Criteria Decision Making (MCDM) issue, by choosing the best alternative at Vc=120m/min, fz=0.065mm/tooth, and ap=0.2mm, where the surface roughness and material removal rate are 0.41µm and 44.1492cm 3 /min respectively. Besides, ANOVA can be used to predict the best parameters set in the milling process based on the regression model. The parameters predicted by ANOVA analysis do not coincide with any implemented parameters. Keywords-surface milling; surface roughness; Taguchi-based TOPSIS; titalium alloy; Ti-6Al-4V; MCDM; MQL I. INTRODUCTION According to the thermophysical properties at elevated temperatures, titanium alloy Ti-6Al-4V is considered as the best material to manufacture parts in medical or euro space industry [1, 2]. However, machining Ti-6Al-4V is complicated because the temperature is usually very high in the contact area between the workpiece and the cutting tool [3–9]. To reduce cutting heat, Metalworking Fluids (MWFs) have been selected as the most common solution [10]. Due to the harmful effects of WMF to the operator’s health and environment, reducing MWF consumption is always considered. In this aspect, dry machining and Minimum Quantity Lubricant (MQL) are two of the most effective alternatives. For the past 20 years, many publications have confirmed the effectiveness of using MQL metalworking in general and Ti-6Al-4V machining in particular. Authors in [11] researched the role of MQL condition in tool wear and surface quality in turning process with an uncoated cutting tool. The research showed the encouraging results where the MQL environment leads to the significant reducing of tool wear and surface roughness mainly through the declining of the temperature in cutting area and the change of the interaction between chip-tool and tool-workpiece during machining. Authors in [12] studied the grinding of Ti- 6Al-4V titanium alloy and the effects of different lubrication conditions on the surface quality. The research showed that vegetable oil can be applied in the milling of titanium alloys under MQL conditions. Hence, the MQL technique was applied in this study work to replace conventional lubricants in the milling process. Corresponding author: Thuy Duong Nguyen Engineering, Technology & Applied Science Research Vol. 11, No. 1, 2021, 6775-6780 6776 www.etasr.com Nguyen et al.: Cutting Parameter Optimization in Finishing Milling of Ti-6Al-4V Titanium Alloy under … Authors in [13] carried out a study research to apply a Multiple Criteria Decision Making (MCDM) approach for enhancing University accreditation process. The results showed that MCDM is suitable to solve multi response optimization problems. Taguchi-based techniques, namely TOPSIS, MOORA, VIKOR, COPRAS, etc. have been often used to solve MCDM problems with high accuracy. Authors in [13, 14] used the TOPSIS method to solve the MCDM problem. These researches show that TOPSIS could be applied to find the best alternative easily and quickly. The problem here is that the TOPSIS or other Taguchi-based technique can help finding the best solutions from the conducted experiments only. This means that this method cannot help predicting or finding the exact optimum parameters set. To come over this disadvantage, new methods can be applied, for example Genetic Algorihm or combinations of some of the conventional methods. Authors in [7] used statistical and soft computing techniques to determine the optimum surface roughness in the milling of Ti-6Al-4V. Their results show that the RSM model could be applied in predicting the optimum surface roughness value in the milling of titanium alloys. However, the predictive result given by Artificial Neural Networks (ANNs) is more accurate than by the Response Surface Method (RSM). Authors in [15] applied an experimental model to optimize and predict the effect of the cutting tool on surface roughness and geometrical characteristics in the drilling of H13 steel. The Evolutionary Multiple Attribute Optimization algorithm was employed to find the optimum parameters set. NSGA-ІІ (Non- dominated Sorting Genetic Algorithm) method was developed, and the regression functions were considered to find the optimum of surface roughness. The successful optimization results are consistent with the experimental findings, and ultimately the optimal set of cutting parameters can be chosen by machining operators according to the application. The study also showed that increased cutting speed and liquid coolant intensity decline surface quality. By contrast, the rising of cutting depth, tool diameter, and feed rate led to better surface quality. Many other studies showed that MQL and vegetable oil are suitable for machining titanium alloy surfaces. The machining of titanium alloys is a major research topic. The challenge is mainly the cost, due to the very high price of the material and the cutting tools leading usually to a reduced number of experiments. In this case, using the Taguchi design method of an experiment is addressed as one of the best solutions [16]. The Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) effectively identifies the best alternative quickly. Authors in [17] succeeded in applying an MCDM model to find the optimum shot-peening parameters set. Authors in [18] were successful in multi-objective optimization on surface quality optimization and MRR in the face milling of AISI 304 steel. The results show that a significant influence of all milling parameters on the MRR and both the feed-rate and the depth of cut have a significant effect on the cutting force. In the current work, information entropy is performed to derive the objective weights of the evaluation criteria. An entropy-based TOPSIS is employed to rank the alternatives in order of preference and then choose the best solution that conforms to the decision maker’s idea [19, 21] II. RESEARCH METHODOLOGY A. Optimization Issues Surface roughness and production rate are two standard and essential criteria that must be considered in machining. Improving surface quality leads to reduced Material Removal Rate (MRR). So, finding the best solution to balance surface roughness and production rate is a critical issue. In this study, two primary responses, including the arithmetical mean roughness (Ra) and specific Material Removal Rate (MRR), are optimized simultaneously using the entropy-based TOPSIS model. The average roughness value is calculated as: �� = ���������� ��� ���� � (1) where Rai is the arithmetic roughness at the i-th position. The production rate is the amount of material removed per time unit and is determined by: MRR = �.��.�� ���� (2) where MRR is the production rate in cm 3 /min, ap is the depth of cut in mm, w is the width of cut in mm, and vf is feed speed in m/min. For the milling process, the cutting parameters, including cutting speed (Vc), depth of cut (ap), and feed rate (vf) can be considered as inputs. The values of cutting parameters are chosen by the suggestions of the cutting tool’s manufacturer and the recommendations of any mold manufacturers. The variance factor data are shown in Table I. In this study, the MQL is fixed at 150ml/h flow rate and 2MPa air pressure. The experiment is performed in 5-axis CNC Machine DMG DMU50 (Germany), and the surface roughness results were measured with the Mitutoyo Surftest JS-310 (Japan). TABLE I. THE VALUE SET OF CUTTING PARAMETERS No. Parameter Symbol Unit Level -1 0 1 1 Cutting Speed Vc m/min 120 210 300 2 Feed fz mm/tooth 0.02 0.06 0.10 3 Depth of cut ap mm 0.1 0.5 0.9 The optimizing issue is described below. The study's approach uses the MCMD method for selecting the best solution for minimizing surface arithmetic roughness (Ra) and maximizing the production rate (MRR). TABLE II. EXPERIMENTAL DATA Run Vc fz ap Ra MRR 1 60 0.03 0.2 0.281 5.42 2 60 0.065 0.4 0.336667 1.08 3 60 0.1 0.6 0.737333 16.25 4 90 0.03 0.4 0.328 21.67 5 90 0.065 0.6 0.321333 10.83 6 90 0.1 0.2 0.506667 2.17 7 120 0.03 0.6 0.358667 32.5 8 120 0.065 0.2 0.411667 43.33 9 120 0.1 0.4 0.635667 16.25 Engineering, Technology & Applied Science Research Vol. 11, No. 1, 2021, 6775-6780 6777 www.etasr.com Nguyen et al.: Cutting Parameter Optimization in Finishing Milling of Ti-6Al-4V Titanium Alloy under … B. Multi-Response Optimization Framework The TOPSIS method was presented in [22, 23], and its steps are: Step 1: Given a set of alternatives, � = ���|� = 1,2, . .��, and a set of criteria, � ! "|# � 1,2, . .$% , where & � !'�"|� � 1,2, . .�,# � 1,2,…$% denotes the set of performance ratings and ) � !)"|# � 1,2,. .$% is the set of weights. The information table I=(A, C, X, W) can be represented as shown in Table III. TABLE III. THE INFORMATION TABLE OF TOPSIS Alternative C1 C2 … Cm A1 x11 x12 … x1m A2 x21 x22 … … … … … An xn1 xn2 … xnm W w1 w2 … wm Step 2: Calculating the normalized rating by [20, 21, 24- 28]: *�" � +,-.∑ 0+,-� 12,3� , � � 1,2 …$;# � 1,2…� (3) Step 3: Calculating the weighted normalized rating by: 5�"0'1 � )"*�"0'1, � � 1,2…�;# � 1,2…$ (4) Step 4: Calculating a positive ideal point (PIS) and a negative ideal point (NIS) by: PIS � �� � �5��0'1,59�0'1,…,5:�0'1� � !