Microsoft Word - ETASR_V11_N6_pp7964-7967 Engineering, Technology & Applied Science Research Vol. 11, No. 6, 2021, 7964-7967 7964 www.etasr.com Alshortan et al.: Low Cost High Gain 8×8 Planar Array Antenna for 5G Applications at 28GHz Low Cost High Gain 8×8 Planar Array Antenna for 5G Applications at 28GHz Hammad H. Alshortan Department of Electrical Engineering University of Hail Hail, Saudi Arabia en.hail1411@gmail.com Abdullah S. Alogla Department of Electrical Engineering University of Hail Hail, Saudi Arabia abdullahogla@gmail.com Mohamed A. H. Eleiwa Department of Electrical Engineering University of Hail Hail, Saudi Arabia mohamed.eleiwa@yahoo.com Muhammad I. Khan Department of Electrical Engineering University of Hail Hail, Saudi Arabia mu.khan@uoh.edu.sa Abstract- In next-generation mobile networks, hundreds of diverse devices aim to be interconnected, posing huge challenges in capacity, coverage, efficiency, reliability, and connectivity. These and other challenges are addressed at Radio Frequency (RF) parts such as several radiating unit antennas, with very fine beamforming capabilities along with the requirements of high gains and minimized size. This work presents an 8×8 Aperture Coupled Microstrip Patch Antenna (AC-MPA) in the form of a planar array modeled for the 28GHz frequency band with high gain and compact size, making it suitable for 5G networks. The antenna is designed using a substrate with overall dimensions of 74.6×85.648×0.107mm 3 and relative permittivity of ε0 = 4.3. Keywords-5G; microstrip patch antenna; planar array I. INTRODUCTION Moving towards 5G means increased data rate needs in order to meet the requirements of high quality applications such as video streaming, endless connectivity, and maximum capacity and coverage with reduced cost [1-3]. Antenna arrays in next generation networks for mobile communication at higher frequency spectra, such as the mm-Wave band, have received attention to meet and support the growing higher data rates with greater throughput and improved performance [4-6]. Very precise and proper consideration is needed regarding the antenna design of future wireless devices due to increased operating frequency [7-10]. It is very challenging to put more antenna elements in a confined specific space. Apart from design issues in terms of physical geometry, designing 5G broadband antennas, operating at multiple frequencies as candidates for 5G bands is a challenging issue. A number of array designs for 5G broadband communication have been proposed [11-13]. Almost all these antennas occupy large space in mobile phone devices operating at very few 5G bands. In this work, a high gain, compact size, and wider band antenna has been proposed. The structure of the antenna contains 64 elements in an 8×8 array arrangement. At different scanning angles, it provides quite considerable radiation beams. The antenna has been modeled, simulated, and analyzed with the CST software [14]. Geometry and structure of the antenna are discussed in detail below. The need of enhanced communication is essential due to the advancement and exponential growth of new technologies such as the massive Internet of Things (IoT), which are less power demanding and low-cost. These technologies consist of connections among hundreds of small size sensors, with specific application such as agriculture, smart cities, smart home, etc.. Services with specific purpose need very high throughput, lower latency, improved security, and reliability. Therefore, communication needs wide coverage and faster service [15]. The proposed spectrum for 5G by 3GPP (3 rd Generation Partnership Project) consists of two bands, one below 6GHz (also known as the sub-six band) and one above 6GHz, typically from 26GHz to 40GHz (also known as millimeter wave) [15-16]. II. ANTENNA DESIGN In order to fulfill the requirements of 5G networks in terms of flexibility, usefulness, proficiency, and integration, microstrip antennas are a considerable solution as they put together all the required characteristics. They are compacted and easy to develop on PCBs (Printed Circuit Boards) cost- effective solutions [17]. The primary structure of these antennas consists of a dielectric material both sides of which contain conducting sheets, one known as the radiating element (patch) and the other as the ground plane. An antenna array must be properly designed so that beam-forming and beam- steering abilities can be achieved. Each element in the array must be separately fed. The proposed antenna is a planar array with 64 elements formed with single elements of dimensions 9.4×10.75×0.107mm 3 . Figure 1 depicts the diagram of the proposed 5G array antenna. Corresponding author: Hammad Alshortan Engineering, Technology & Applied Science Research Vol. 11, No. 6, 2021, 7964-7967 7965 www.etasr.com Alshortan et al.: Low Cost High Gain 8×8 Planar Array Antenna for 5G Applications at 28GHz (a) (b) Fig. 1. Single element patch antenna. (a) Top view, (b) side view. III. SINGLE ELEMENT ANTENNA Figure 2 shows the schematic diagram of the single element of antenna and Figure 3 shows its S11 result. These elements are further combined to form an antenna array. From the results it can be observed that return loss below -26dB is achieved at 28GHz and a bandwidth around 4GHz is obtained. The values of the parameters affect the performance of the antenna in terms of its matching and band. The optimized antenna parameters are shown in Table I. (a) (b) (c) (d) Fig. 2. Array antenna single element multiple views: (a) top, (b) bottom, (c) side, and (d) end. TABLE I. ANTENNA ELEMENT PARAMETER DESCRIPTION Name Parameter Value (mm) Frequency 27.89 Port_width 2.305 Port_height 0.967 Wavelength center 10.749 Groundplane_width 10.749 Groundplane_length 9.352 Groundplane_feed_extension -1.702 La 2.799 Wa 0.107 Lf 2.973 Wf 0.209 Lp 3.978 Wp 5.374 Εb 4.3 Εt 1 Ls 0.478 Hb 0.107 Ht 0.859 Tanδb 0 Tanδt 0 IV. THE PROPOSED 5G ANTENNA ARRAY The proposed design of the 5G antenna array with 64 elements formed using the discussed above single element is illustrated in Figure 4. The design has overall dimensions of 74.6×85.648×0.107mm 3 . As can be seen, 64 compact antenna components with distance d are used to make an array in the top segment of the PCB. The antenna is constructed on the FR- 4 as bottom substrate and vacuum as the top part. Fig. 3. S11 of the single element antenna. Fig. 4. Array arrangement of the 8×8 (64 elements) antenna. The antenna array was simulated in CST and the obtained values of S11 are shown in Figure 5. It can be observed that the designed antenna provides wide bandwidth more than 4.5GHz with an acceptable value of return loss at 28GHz, i.e. -28.5dB. Similarly, after the simulation of the antenna, a gain of 10.34dBi is achieved. Figure 6 gives the graphical representation of the 3D radiation pattern plot. Fig. 5. S11 graph of the antenna array. Lp Wp Engineering, Technology & Applied Science Research Vol. 11, No. 6, 2021, 7964-7967 7966 www.etasr.com Alshortan et al.: Low Cost High Gain 8×8 Planar Array Antenna for 5G Applications at 28GHz Fig. 6. 3D Radiation pattern (gain) at 28GHz. The results obtained for the s-parameter of the 64-element antenna, simulated and analyzed in this work are shown in Figure 7. It can be observed that a very consistent and directional response is obtained and radiation with a very acceptable s-parameter is attained. Figures 8-9 show the E- plane and H-plane patterns in polar and Cartesian coordinates at 28GHz. Fig. 7. S-parameter of the array arrangement in an 8×8 manner. (a) (b) Fig. 8. E-plane pattern in (a) polar and (b) Cartesian coordinates. (a) (b) Fig. 9. H-plane pattern in (a) polar and (b) Cartesian coordinates. The elements of the proposed array exhibit great performance. The efficiencies (radiation and total) of the proposed planar antenna array are exhibited in the related Figures. It can be observed that adequate efficiency outcomes are achieved at 25-30GHz. Higher than 97% radiation efficiency is gained. Likewise, more than 70% total efficiency has been attained for the introduced array elements [18-19]. It can also be observed that the proposed 5G antenna design offers steady radiation (patterns/beams) with enough gain [20]. V. COMPARISON WITH STATE OF THE ART ANTENNAS A comparison with known related antennas is shown in Table II. It can be understood that the presented antenna is a low-cost antenna with much improved impedance bandwidth and acceptable peak gain in comparison with other known, state of the art antennas. The antenna has efficient planar structure, it is easy to implement and has a high directive gain. The presented antenna achieves an impedance bandwidth of 29% and a peak gain of 10.5dBi which outperforms the other antennas, and is adequate for millimeter-wave communication. It has a much wider bandwidth of 4.5GHz. TABLE II. COMPARISON OF THE PROPOSED ANTENNA WITH PREVIOUS WORKS Ref./Year Freq. band (GHz) Bandwidth (GHz) Peakg gain (dBi) Type [21]/2021 24.25-29.5 6 0-5 Phased array [22]/2018 39–49.3 2.0 5.5 Reflector, omni [23]/2017 24–32 3.5 9 SIW/tapered slot [24]/2016 57–67 - 2.2 Micro-strip This work 25-30 4.5 10.5 Planar array Engineering, Technology & Applied Science Research Vol. 11, No. 6, 2021, 7964-7967 7967 www.etasr.com Alshortan et al.: Low Cost High Gain 8×8 Planar Array Antenna for 5G Applications at 28GHz VI. CONCLUSION The aim of this work was to present a new and compact array with WB function for 5G mobile communication. Its arrangement includes 64 compact antennas in an 8×8 planar form, positioned at the top edge of the FR4-material mainboard. The fundamental properties of the proposed antenna were examined. The introduced array shows satisfactory features over its operation band, which can be appropriate for multi-mode communications in 5G systems. This antenna has a considerable bandwidth over 4.5GHz, a gain of about 10.5dBi and is offered as a solution for beamforming application scenarios. Moreover, not only it has small dimensions but also it possesses a modular structure that can be simply scalable for a greater number of ports and elements. REFERENCES [1] A. Osseiran et al., "Scenarios for 5G mobile and wireless communications: the vision of the METIS project," IEEE Communications Magazine, vol. 52, no. 5, pp. 26–35, May 2014, https://doi.org/10.1109/MCOM.2014.6815890. [2] P. Gupta, "Evolvement of mobile generations: 1G to 5G," International Journal For Technological Research In Engineering, vol. 1, no. 3, pp. 152–157, 2013. [3] W. Roh et al., "Millimeter-wave beamforming as an enabling technology for 5G cellular communications: theoretical feasibility and prototype results," IEEE Communications Magazine, vol. 52, no. 2, pp. 106–113, Feb. 2014, https://doi.org/10.1109/MCOM.2014.6736750. [4] Y. Wang, J. Li, L. Huang, Y. Jing, A. Georgakopoulos, and P. Demestichas, "5G Mobile: Spectrum Broadening to Higher-Frequency Bands to Support High Data Rates," IEEE Vehicular Technology Magazine, vol. 9, no. 3, pp. 39–46, Sep. 2014, https://doi.org/10.1109/ MVT.2014.2333694. [5] N. Ojaroudi Parchin, M. Alibakhshikenari, H. Jahanbakhsh Basherlou, R. A. Abd-Alhameed, J. Rodriguez, and E. Limiti, "MM-Wave Phased Array Quasi-Yagi Antenna for the Upcoming 5G Cellular Communications," Applied Sciences, vol. 9, no. 5, Jan. 2019, Art. no. 978, https://doi.org/10.3390/app9050978. [6] N. Ojaroudi Parchin et al., "Frequency Reconfigurable Antenna Array for MM-Wave 5G Mobile Handsets," in Broadband Communications, Networks, and Systems, Cham, 2019, pp. 438–445, https://doi.org/ 10.1007/978-3-030-05195-2_43. [7] N. Amitay, V. Galindo, and C. P. Wu, Theory and analysis of phased array antennas. New York, NY, USA: Wiley-Interscience, 1972. [8] N. Ojaroudiparchin, M. Shen, and G. F. Pedersen, "Multi-layer 5G mobile phone antenna for multi-user MIMO communications," in 2015 23rd Telecommunications Forum Telfor, Belgrade, Serbia, Nov. 2015, pp. 559–562, https://doi.org/10.1109/℡FOR.2015.7377529. [9] W. Hong, K. Baek, Y. Lee, and Y. G. Kim, "Design and analysis of a low-profile 28 GHz beam steering antenna solution for Future 5G cellular applications," in 2014 IEEE MTT-S International Microwave Symposium (IMS2014), Tampa, FL, USA, Jun. 2014, https://doi.org/10.1109/MWSYM.2014.6848377. [10] N. Ojaroudiparchin, M. Shen, S. Zhang, and G. F. Pedersen, "A Switchable 3-D-Coverage-Phased Array Antenna Package for 5G Mobile Terminals," IEEE Antennas and Wireless Propagation Letters, vol. 15, pp. 1747–1750, 2016, https://doi.org/10.1109/LAWP.2016. 2532607. [11] S. Zhang, I. Syrytsin, and G. F. Pedersen, "Compact Beam-Steerable Antenna Array With Two Passive Parasitic Elements for 5G Mobile Terminals at 28 GHz," IEEE Transactions on Antennas and Propagation, vol. 66, no. 10, pp. 5193–5203, Oct. 2018, https://doi.org/ 10.1109/TAP.2018.2854167. [12] R. Rodríguez-Cano, S. Zhang, and G. F. Pedersen, "Beam-steerable multi-band mm-wave bow-tie antenna array for mobile terminals," in 12th European Conference on Antennas and Propagation (EuCAP 2018), London, UK, Apr. 2018, https://doi.org/10.1049/cp.2018.0418. [13] N. O. Parchin, R. A. Abd-Alhameed, and M. Shen, "Design of Low Cost FR4 Wide-Band Antenna Arrays for Future 5G Mobile Communications," in 2019 International Symposium on Antennas and Propagation (ISAP), Xi’an, China, Oct. 2019. [14] CST Studio Suite 3D EM simulation and analysis software. Simula. [15] Making 5G NR a reality. San Diego, CA, USA: Qualcomm, 2016. [16] G. A. Akpakwu, B. J. Silva, G. P. Hancke, and A. M. Abu-Mahfouz, "A Survey on 5G Networks for the Internet of Things: Communication Technologies and Challenges," IEEE Access, vol. 6, pp. 3619–3647, 2018, https://doi.org/10.1109/ACCESS.2017.2779844. [17] C. A. Balanis, Antenna Theory: Analysis and Design, 4th ed. Hoboken, NJ, USA: Wiley, 2016. [18] M. O. Dwairi, "Increasing Gain Evaluation of 2×1 and 2×2 MIMO Microstrip Antennas," Engineering, Technology & Applied Science Research, vol. 11, no. 5, pp. 7531–7535, Oct. 2021, https://doi.org/ 10.48084/etasr.4305. [19] M. R. Rezoug, M. Benaouadj, D. Taibi, and R. Chenni, "A New Optimization Approach for a Solar Tracker Based on an Inertial Measurement Unit," Engineering, Technology & Applied Science Research, vol. 11, no. 5, pp. 7542–7550, Oct. 2021, https://doi.org/ 10.48084/etasr.4330. [20] H. V. T. Chi, D. L. Anh, N. L. Thanh, and D. Dinh, "English- Vietnamese Cross-Lingual Paraphrase Identification Using MT-DNN," Engineering, Technology & Applied Science Research, vol. 11, no. 5, pp. 7598–7604, Oct. 2021, https://doi.org/10.48084/etasr.4300. [21] X. Gu et al., "Antenna-in-Package Integration for a Wideband Scalable 5G Millimeter-Wave Phased-Array Module," IEEE Microwave and Wireless Components Letters, vol. 31, no. 6, pp. 682–684, Jun. 2021, https://doi.org/10.1109/LMWC.2021.3071917. [22] K. Fan, Z.-C. Hao, Q. Yuan, J. Hu, G. Q. Luo, and W. Hong, "Wideband Horizontally Polarized Omnidirectional Antenna With a Conical Beam for Millimeter-Wave Applications," IEEE Transactions on Antennas and Propagation, vol. 66, no. 9, pp. 4437–4448, Sep. 2018, https://doi.org/ 10.1109/TAP.2018.2851363. [23] B. Yang, Z. Yu, Y. Dong, J. Zhou, and W. Hong, "Compact Tapered Slot Antenna Array for 5G Millimeter-Wave Massive MIMO Systems," IEEE Transactions on Antennas and Propagation, vol. 65, no. 12, pp. 6721–6727, Dec. 2017, https://doi.org/10.1109/TAP.2017.2700891. [24] M. H. Ghazizadeh and M. Fakharzadeh, "60 GHz Omni-directional segmented loop antenna," in 2016 IEEE International Symposium on Antennas and Propagation (APSURSI), Fajardo, PR, USA, Jun. 2016, pp. 1653–1654, https://doi.org/10.1109/APS.2016.7696533.