IHJPAS. 36(2)2023 171 This work is licensed under a Creative Commons Attribution 4.0 International License. Abstract The Optical Fiber sensor based on the Surface Plasmon Resonance (SPR) technology has been a successful performance sensing and presents high sensitivity. This thesis investigates the performance of several structure of SPR sensor in field of refractive index and chemical applications. A structure of Multi-Mode Fiber- Single Mode Fiber- Multi Mode Fiber (MMF- SMF-MMF) had been designed and manufactured. The outer diameter of the SMF sensing region) had been reduced to (65, 45, and 25) µm. This is achieved using the chemical etching method. Then this sensitive area coated with gold layer using Magnetron Sputtering plasma System. The thickness of the gold layer is (40 nm).In most of the previous research in this field of the line of research: the surface Plasmon resonance sensor experiment is conducted using light sources with a wide range of wavelengths. To improve the accuracy of analysis (resolution), helium-neon laser was used as a light source when determining the Plasmon resonance wavelength as a function of the index of refraction of chemical solutions. The sensitivity for samples of salt solutions was 140 and 142 (nm/RIU) for the two dips of the spectrum and the sensitivity for samples of glucose solutions was 38 and 42 (nm/RIU) for the two dips of the spectrum. Keywords: Chemical optical fiber sensor, Chemical etching, single mode optical fiber, Laser, Surface Plasmon Resonance. 1. Introduction The first studies in optical fiber sensors that adopted surface Plasmon resonance were conducted in 1993 by Jorgenson and Yee[1].Fiber-optic sensors have many applications in environmental, communication technology, biological, chemical, and medical fields. This is due to the fact that these sensors are small in size and have high sensitivity for minimal changes in parameters of the samples to be sensed [1,2].The surface Plasmon resonance (SPR) sensor relies on the fact that the surface of Plasmon is stimulated by electromagnetic waves and influenced by doi.org/10.30526/36.2.3002 Article history: Received 6 October 2022, Accepted 24 October 2022, Published in April 2023. Ibn Al-Haitham Journal for Pure and Applied Sciences Journal homepage: jih.uobaghdad.edu.iq Employment the Laser to Fabricate the Surface Plasmon Resonance Sensor Tammara Jamal Mossa Department of physics, College of science for women, University of Baghdad, Baghdad, Iraq. tamara.jamal1204a@csw.uobaghdad.edu.iq Haider Y. Hammod Department of physics, College of science for women, University of Baghdad, Baghdad, Iraq. haider.y@csw.uobaghdad.edu.iq https://creativecommons.org/licenses/by/4.0/ mailto:tamara.jamal1204a@csw.uobaghdad.edu.iq mailto:haider.y@csw.uobaghdad.edu.iq IHJPAS. 36(2)2023 172 changes in the refractive index of material around the surface of the metal, which is deposited very thin on the optical fiber core, as an alternative to the lower refractive index of the optical fiber core material [3,4,5].This method of optical detection relies on the principle of the interaction between the free electron waves present in metals and the electromagnetic waves falling on them. Resonance occurs when the wavelength of the incident light is equal to the wavelength of the oscillation of free electrons. As a result of this reaction, the intensity of the wave reflected off the medium is due to a large portion of its energy being transferred to the deposition layer of the metal [6,7].The most important optical elements that can be used to study these processes are high refractive indices prism, optical gratings, and optical fibers that have become widely used recently. These sensors were widely used in science, education, and industry due to the importance of non- destructive samples, its high sensitivity, and acceptable selectivity. When light is absorbed, the surface Plasmon resonance sensor detects resonant electron oscillations across both the metal surface and a dielectric substrate. The advantages of optical fiber sensors are that they are highly sensitive, light in weight, and in small diameter, its exposure to electromagnetic waves is minim [8]. This sensor is usually made of silica fiber and its mode (SMF) and multimode (MMF) types, and because of its cost, it has been replaced by a plastic fiber, which is highly flexible and easy to design. In order to create a strong optical fiber surface Plasmon resonance, it is crucial to improve its efficiency factors including such sensitivity, signal to noise ratio, etc. (SPR). These output properties are mostly influenced by the sensor's geometric layout and a few physical factors, such as the existence of surface treatments and the materials' dielectric continuity. It is claimed that the ideal geometry and the key variables that govern how the sensor interacts are the source of the issue [3]. 2. Theoretical concepts There are a number of parameters commonly studied to measure the performance of such sensors, which use optical fibers as a key component in their construction, by comparing the properties of the input light to those of the output light. The first of these variables is sensitivity, which is defined as the ratio between the change in resonance wavelength values and the corresponding change in the index of refraction of ambient matter and contact with metal, according to the following equation [9]. Sn = δλres δns ------ (1) Where (Sn)is the sensitivity and (λres) is the resonance wavelength and (ns) is the equivalent change in the index of refraction. The most important variable that we've been looking at is how important it is to use a laser instead of a light. This variable is the resolution of the sensor and can be mathematically defined as the least change in the index of refraction of a material that can be detected by the sensor used. It is given the following relationship [9]. 𝑅 = δns 𝛿𝜆𝑟𝑒𝑠 𝛿𝜆𝐷𝑅 --------- (2) Where (𝑅)is the resolution (𝛿𝜆𝐷𝑅) is the spectral resolution of the spectrometer IHJPAS. 36(2)2023 173 Fig [1] the photographic image of SPR sensor based on macro bending optical fibers where [1] He: Ne laser Source, [2] SPR macro bending Sensor, [3] different solutions, [4] OSA with Pc. they are arranged. 3. Preparing sensor and setup: The main structure of this sensor consists of three types of optical fiber: the central fiber, which is the sensing region of the single mode (SMF) type, is associated at the end with another optical fiber, which is multimode (MMF), to control the entry and exit of the light signal. SMF fiber with a standard core/cladding diameter (10/125) µm and a suitable length of 3cm.The fiber was stripped and thoroughly cleaned. Then the stripped area was immersed in dilute hydrofluoric acid at 40% concentration for 180 seconds to obtain a diameter of 65µm. The fiber is then cleaned again to deactivate the acid and completely stop the chemical reaction by placing the fiber in distilled water for several minutes. The diameter of the outer fiber has been measured using a (Nikon Eclipse ME600) type of optical microscope with a magnification to (100X). To obtain a layer of surface Plasmon metal, a previous stripped fiber coating with gold Nano particles is done. The most common method used is sputtering to produce a thin film of this material. This method is known as physical vapor deposition (PVD) and occurs in a vacuum of air, where the Nano materials are deposited on the surface of the samples by extracting atoms from the material to be deposited and concentrating them on the samples. As for the gold-layer thickness obtained by this method, it was 40 nm by controlling the process of spraying the thickness of the gold layer could be controlled in this work 15 min was the required time to get this thickness. After this stage was completed, this part of the sensor at both ends was linked to an optical fiber of a (MMFs) type by using an optical fiber splicer machine Fujikura (FSM-60S Japan). With regard to the preparation of the test samples, which are represented by solutions of different concentrations and correspond to different refractive indices. They were made of both salt and sugar. Concentrations ranged from (0.05 - 0.45) moll/L and these refractive indices were measured using a device Refractometer ((BOECO Digital ABBE Refractometer). For the setup of the experiment, one end of the sensor was delivered to a 632.8 nm Helium-Neon laser source, and the other end was delivered to an optical spectrum analyzer (OSA) (Ocean Optics USB- 2000) with range (200-1100) nm. The reaction area of the sensor, SMF, is submerged in saline and sugar solutions, alternately to show the effect of changing concentrations on the output signal. The reflection spectrum is directly measured and analyzed for each reflection state of the transmitted signal. Figures (1, 2) shows the photographic image at the set up. 1 2 4 3 IHJPAS. 36(2)2023 174 4. Results and discussion: At this stage, some changes have been made to experiments that are typically conducted in this field, using a laser source instead of a conventional light source and increasing the intensity losses of the light entering the sensor by bending the optical fiber at the sensing zone to improve its performance. 4.1 influence of the fiber bending: To increase the intensity of the light that's involved in the interaction with the surface wave of the metal, the bending of the optical fiber increases the intensity losses of the light that's passing through the optical fiber. When we draw the relationship between intensity and wavelength, for both cases, with and without bending in straight optical fiber and the micro bending fiber, we see that there are multiple dips that represent the intentional losses in intensity that will improve the performance of the sensor. Figure (3) shows that. Fig [3] the influence of micro bending in transmitting light Fig [2] a schematic diagram of the main experimental components and how they are arranged. IHJPAS. 36(2)2023 175 4.2 Measure the resonance wavelength For NaCl solutions: To test the performance of the sensor, saline solutions of different concentrations (corresponding to different refractive indices) were used. When observing the optical spectrum analyzer, the relationship between laser wavelength and the reflectivity of the metal surface was drawn. In the presence of the solutions, the wavelengths of the plasma resonance and for two dips were determined. The sensitivity of the sensor was calculated by using the equation (1) also the resolution of the sensor was calculated using equation (2) for two dips. From Tables (1, 2) and Figure (4) we can see that there is an improvement in this parameters. Table (1) illustrate the values of resonance wavelengths and calculated sensor parameters RI of NaCl solution (RIU) Resonance Wavelength (nm) for dip 1 Resonance Wavelength (nm) for dip2 1.3436 628.467 635.467 1.344 628.485 635.495 1.3445 628.565 635.572 1.3451 628.602 635.612 1.3456 628.681 635.68 1.3461 628.758 635.768 1.3468 628.823 635.833 1.347 628.903 635.901 1.3476 628.983 635.993 1.3481 629.095 636.095 Table (2) the sensitivities and spectral resolution of macro bending SPR- optical fiber immersed into salt solution Resonance dip Sensitivity (nm/RIU) Spectral Resolution (RIU) Dip 1 140 7.14 x10-4 Dip 2 142 7x10-4 IHJPAS. 36(2)2023 176 4.2.1 Resonance wavelength as a function of RI Based on the previously calculated values listed in two Tables (1, 2), the relationship between resonance wavelengths are drawn as a function of the different refractive coefficients of saline for both dips. When looking at these relationships, a direct relationship between the two variables was found, meaning that increasing the refractive index of the saline shifted the resonant wavelength towards the long values (red shift). Figures (5) show these relations. 627.5 628.0 628.5 629.0 629.5 630.0 -2500 -2000 -1500 -1000 -500 0 500 1000 (b) dip 1 R e fl e c ta n c e ( R .U .) Wavelength (nm) 628 630 632 634 636 638 -3000 -2500 -2000 -1500 -1000 -500 0 500 1000 1500 (a) dip 2 dip 1 R e fl e c ta n c e ( R .U .) Wavelength (nm) RI=1.3436 RIU RI=1.344 RIU RI=1.3445 RIU RI=1.3451 RIU RI=1.3456 RIU RI=1.3461 RIU RI=1.3468 RIU RI=1.347 RIU RI=1.3476 RIU RI=1.3481 RIU Fig [4] the relationships between wave length and reflectance recorded by OSA in RPS for NaCl at two dips (a) the all spectrum, (b) zoom spectrum of dip1, and (c) zoom spectrum of dip2. 635.0 635.2 635.4 635.6 635.8 636.0 636.2 636.4 636.6 636.8 -3000 -2500 -2000 -1500 -1000 -500 0 500 1000 dip 2 (c) R e fl e c ta n c e ( R .U .) Wavelength (nm) IHJPAS. 36(2)2023 177 4.3 Measure the resonance wavelength For C12H22O11 solutions: In this section of research, the sensor was tested using another chemical compound, and all previous brine steps were repeated. As a first step, the compound was prepared in close concentrations, corresponding to different refractive indices with very little change in values, distinguishing this sensor from the others that detect the smallest changes in the samples being tested. This gives different values for the resonance wavelengths for each corresponding index of refraction. After drawing the relationships between the wavelength of light incident at the reaction area of the sensor and its reflectance from the contact layer between the metal and the chemical solution, the Figure (6) were obtained. Using the equations (1, 2) and with the help of the figures drawn, the sensitivity and resolution of the sensor can be calculated, as shown in the Tables (3, 4). Table (3) the values of resonance wavelengths and calculated sensor parameters RI of C12H22O11 solution (RIU) Resonance Wavelength (nm) for dip 1 Resonance Wavelength (nm) for dip2 1.3454 628.479 635.487 1.3481 628.532 635.535 1.3503 628.591 635.585 1.353 628.695 635.78 1.3553 628.774 635.877 1.358 628.872 635.933 1.3604 628.929 636.001 1.3631 628.992 636.096 1.3654 629.085 636.181 1.3682 629.102 636.232 1.343 1.344 1.345 1.346 1.347 1.348 628.4 628.5 628.6 628.7 628.8 628.9 629.0 629.1 629.2 (a) R e s o n a n c e W a v e le n g th ( n m ) Refractive index of NaCl solution (RIU) measured data for dip 1 linear fitting Y= A+ 140 X R=0.99 1.343 1.344 1.345 1.346 1.347 1.348 635.4 635.5 635.6 635.7 635.8 635.9 636.0 636.1 636.2 (b) R e s o n a n c e W a v e le n g th ( n m ) Refractive index of NaCl solution (RIU) measured data for dip 2 linear fitting Y= A+ 142 X R=0.99 Fig [5] the relationships of RI VS resonance wavelength for NaCl at two dips (a) for dip 1, (b) for dip 2 IHJPAS. 36(2)2023 178 4.3.1 Resonance wavelength as a function of RI A final step in this research is to draw the relationships between the values of resonance wavelengths obtained from the above figures in the tables for both dips Here we can also see that there is a direct correlation between the indices of refraction and the wavelength of resonance, which is shown by the linear relationship between the two variables. By looking at the Figure (7) Table (4) the sensitivities and spectral resolution of macro bending SPR- optical fiber immersed into glucose solution Resonance dip Sensitivity (nm/RIU) Spectral Resolution (RIU) Dip 1 38 2.6x10-4 Dip 2 42 2.3x10-4 627.5 628.0 628.5 629.0 629.5 630.0 -2500 -2000 -1500 -1000 -500 0 500 1000 (b) dip 1 R e fl e c ta n c e ( R .U .) Wavelength (nm) 635.0 635.2 635.4 635.6 635.8 636.0 636.2 636.4 636.6 636.8 -3000 -2500 -2000 -1500 -1000 -500 0 500 1000 1500 dip 2 (c) R e fl e c ta n c e ( R .U .) Wavelength (nm) 628 630 632 634 636 638 -3000 -2500 -2000 -1500 -1000 -500 0 500 1000 1500 (a) dip 2 dip 1 R e fl e c ta n c e ( R .U .) Wavelength (nm) RI=1.3454 RIU RI=1.3481 RIU RI=1.3503 RIU RI=1.353 RIU RI=1.3553 RIU RI=1.358 RIU RI=1.3604 RIU RI=1.3631 RIU RI=1.3654 RIU RI=1.3682 RIU Fig [6] the relationships between wave length and reflectance recorded by OSA in RPS for C12H22O11 at two dips (a) the all spectrum, (b) zoom spectrum of dip 1, and (c) zoom spectrum of dip2. IHJPAS. 36(2)2023 179 below, we can see that there is a clear sense of the least change in refractive index that is reflected in the corresponding values of change in resonance wavelengths. 5. Conclusions In examining the results of this research, we can conclude that:  Surface Plasmon is very efficient in sensitizing different chemicals with very different refractive indices, even very small differences.  When Laser was used as a light source instead of the traditional light sources produces good results in resolution and sensitivity, as evidenced by the appearance of two distinct dips of Plasmon resonance wavelengths.  Adding micro bending to the optical fiber leads to a deliberate increase in the loss of light in the reaction area, thereby improving the performance of the sensor. References 1. Wang, S.; Li, S. Surface Plasmon Resonance Sensor Based on Symmetrical Side-Polished Dual-Core Photonic Crystal Fiber. Opt. Fiber Techno, 2019, 51, 96-100. 2. Jassam, G.M.; Alâ, S.S.; Sultan, M.F. Fabrication of a Chemical Sensor Based on Surface Plasmon Resonance Via Plastic Optical Fiber. Iraqi Journal of Science, 2020, 61, 765-771. 3. Yasser, N.; Ali, N.A.; Sulaiman, L.H. The Polymer Optical Fiber Sensor Side-Pumped with Polymer Clad Doped Lasing Compounds. Iraqi Journal of Science, 2018, 59, 294-298. 4. Mescia, L.; Prudenzano, F. Advances on Optical Fber Sensors. Fibers, 2014, 2, 1, 1-23. 1.345 1.350 1.355 1.360 1.365 1.370 635.4 635.5 635.6 635.7 635.8 635.9 636.0 636.1 636.2 636.3 (b) R e s o n a n c e W a v e le n g th ( n m ) Refractive index of C 12 H 22 O 11 solution (RIU) measured data for dip 2 linear fitting Y= A+ 42 X R=0.99 1.345 1.350 1.355 1.360 1.365 1.370 628.4 628.5 628.6 628.7 628.8 628.9 629.0 629.1 629.2 (a) R e s o n a n c e W a v e le n g th ( n m ) Refractive index of C 12 H 22 O 11 solution (RIU) measured data for dip 1 linear fitting Y= A+ 38 X R=0.99 Fig [7] the relationships of RI VS resonance wavelength for C12H 22O11 at two dips (a) for dip1, (b) for dip2 IHJPAS. 36(2)2023 180 5. Sultan, M.F.; Al-Zuky, A.A.; Kadhim, S.A.; Al-saleh, A.H. Performance Parameters Evaluation of Surface Plasmon Resonance Based Fiber Optic Sensor with Different Bilayer Metals: Theoretical Study, Al-Mustansiriyah Journal of Science, 2018; 29, 1, 195-203. 6. Duan, Q.; Liu, Y.; Chang, S.; Chen, H.; Chen, J.H. Surface Plasmonic Sensors: Sensing Mechanism and Recent Applications, Sensors. 2021, 21, 16, 5262-30. 7. Gao, M.; Yang, W.; Wang, Z.; Lin, S.; Zhu, J.; Yang, Z. Plasmonic Resonance-Linewidth Shrinkage to Boost Biosensing. Photonics Res, 2020, 8, 7, 1226-1235. 8. Lee, S.; Song, H.; Ahn, H.; Kim, S.; Choi, JR.; Kim, K. Fiber-Optic Localized Surface Plasmon Resonance Sensors Based on Nano Materials. Sensors. 2021, 21, 3, 819. 9. Sultan, M.F.; Al-Zuky, A.A.; Kadhim, S.A. Surface Plasmon Resonance Based Fiber Optic Sensor: Theoretical Simulation and Experimental Realization. Al-Nahrain Journal of Science, 2018, 21, 1, 65-70