APPLICATION OF DIGITAL CELLULAR RADIO FOR MOBILE LOCATION ESTIMATION IIUM Engineering Journal, Vol. 19, No. 1, 2018 Jebun et al. 48 PRODUCTION AND STABILITY OF MYCO- FLOCCULANTS FROM LENTINUS SQUARROSULUS RWF5 AND SIMPLICILLIUM OBCLAVATUM RWF6 FOR REDUCTION OF WATER TURBIDITY NESSA JEBUN, MD. ZAHANGIR ALAM*, ABDULLAH AL-MAMUN AND RAHA AHMAD RAUS Bioenvironmental Engineering Research Centre (BERC), Department of Biotechnology Engineering, Faculty of Engineering, International Islamic University Malaysia, Jalan Gombak, 53100 Kuala Lumpur, Malaysia. * Corresponding author: zahangir@iium.edu.my (Received: 8th May 2018; Accepted: 21st Nov 2017; Published on-line: 1st June 2018) https://doi.org/10.31436/iiumej.v19i1.843 ABSTRACT: The production and stability of two novel myco-flocculants produced by river water fungus (RWF) were investigated. Screening tests were conducted to find suitable nutrients, pH, nutrient concentration, inoculum dose, and stability for two myco- flocculants L. squarrosulus (RWF5) and S. obclavatum (RWF6). The strains showed good flocculating activity in reducing turbidity of kaolin suspension while malt extract was used as nutrient source. Supernatants of RWF5 and RWF6 were able to reduce turbidity from 900±10 NTU to 46 NTU (95%) and 195 NTU (78%), respectively. In order to enhance the production, optimization of cultivation conditions were studied using a one-factor-at-a- time (OFAT) method. L. squarrosulus (RWF5) reduced 96% of turbidity at optimum conditions, comprising of 0.1% (w/v) malt extract, 3% (v/v) inoculum dose, and initial pH 7.0 for 6 days. The results of the compatible mixed culture showed good flocculation activity at 88% compared to a single culture of S. obclavatum at 78%. On the other hand, L. squarrosulus showed better turbidity reduction in the single culture rather than the mixed culture. The stability of L. squarrosulus and S. obclavatum supernatants showed excellent turbidity reduction over a wide pH range of 4-8 with the maximal flocculation rate of 96% and 90%, respectively, at pH 7.0. They also exhibited high turbidity removal ability in a temperature range of 4 oC – 55 oC for 24h with a maximum turbidity removal rate of 96% (RW5) and 87% (RW6) at 25 oC. Time stability of the L. squarrosulus supernatant showed good turbidity removal potential at above 90% at room temperature (28± 2 oC) and 85% at low temperature (4 oC) for 12 days. The high flocculating rate of the myco-flocculants and their good stability under wide range of temperature indicated their potentiality as biodegradable flocculants for water and wastewater treatment industry. ABSTRAK: Keberhasilan dan kestabilan dua myco-gumpalan baharu oleh kulat air sungai (RWF) telah dikaji. Ujian penapisan telah dijalankan untuk mencari nutrien sesuai, pH, kepekatan nutrien, dos inokulum dan kestabilan dua myco-gumpalan L. squarrosulus (RWF5) dan S. obclavatum (RWF6). Rantaian menunjukkan aktiviti gumpalan yang baik dalam mengurangkan kekeruhan air sungai dengan penggantungan koalin di mana ekstrak malt telah digunakan sebagai sumber nutrien. Larutan supernatan RWF5 dan RWF6, masing-masing mampu mengurangkan kekeruhan dari 900±10 NTU kepada 46 NTU (95%) dan 195 NTU (78%). Bagi meningkatkan pengeluaran, keadaan optimum bagi menggalakkan hasil telah diselidiki menggunakan kaedah Satu Faktor pada Tiap Masa (OFAT). Pada takat optimum, L. squarrosulus (RWF5) mengurangkan 96% kekeruhan, IIUM Engineering Journal, Vol. 19, No. 1, 2018 Jebun et al. 49 ianya terdiri daripada ekstrak malt 0.1% (w/v), dos inokulum 3% (v/v) dan pH awal 7.0 selama 6 hari. Keputusan kultur campuran yang sesuai menunjukkan aktiviti penggumpalan yang baik pada 88% berbanding kultur sendirian S. obclavatum pada 78%. Pada waktu sama, L. squarrosulus menunjukkan pengurangan kekeruhan yang lebih baik dalam kultur sendirian berbanding kultur campuran. Kestabilan larutan supernatan L. squarrosulus dan S. obclavatum menunjukkan pengurangan kekeruhan yang sangat baik pada pH yang luas iaitu 4-8 dengan kadar maksimum kekeruhan pada 96% dan 90%, pada pH 7.0 masing-masing. Keduanya menunjukkan kebolehan penyingkiran kekeruhan yang tinggi pada skala suhu 4 oC – 55 oC selama 24 jam dengan kadar nyah kekeruhan maksimum pada 96% (RW5) dan 87% (RW6) pada suhu 25 oC. Kestabilan masa larutan supernatan L. Squarrosulus menunjukkan potensi penyingkiran kekeruhan terbaik atas 90% pada suhu bilik (28± 2 oC) dan 85% pada suhu rendah (4 oC) selama 12 hari. Kadar gumpalan yang tinggi oleh myro-gumpalan dan kestabilan yang baik pada julat suhu yang luas menunjukkan potensinya sebagai agen biodegradasi gumpalan kepada air dan industri rawatan loji air. KEYWORDS: flocculation; jar test; Lentinus squarrosulu; mixed culture; Simplicillium obclavatu; stability; turbidity 1. INTRODUCTION Chemical flocculants are widely used in wastewater and drinking water treatment, food and fermentation industries, as well as in downstream processing due to their high flocculating efficiency and cost-effectiveness. [1, 2] Generally, flocculating agents that have the most usage in water treatment are the synthetic ones such as aluminium sulphate, ferric chloride, lime, and synthetic polymers. [3, 4] Aluminium salts are the most widely used coagulant in water and wastewater treatment because of their proven performance and cost effectiveness. However, chemical coagulants cannot be easily degraded in nature and may result in various health and environmental problems. [5] Compared with chemical flocculants, bioflocculants have more advantages, such as being environmentally friendly due to their biodegradability, largely nontoxic with no secondary pollution, and harmless to both humans and animals. [6] Therefore, bioflocculants have recently gained global attention in research because they hold immense potential in replacing chemical flocculants. For example, Li et al. [7] reported that B. licheniformis produced ZS-7 bioflocculant is expected to be a potential replacement for conventional synthetic flocculants such as PAC (polyaluminum chloride) and PAM (polyacrylamide) for the treatment of low temperature and room temperature (25 oC) drinking water. Similarly, Gong et al. [8] reported Serratia ficaria produced bioflocculant SF-1 showed 91.8 – 93.7% turbidity removal from wastewater, which is better than that of PAC and PAM. Aspergillus flavus produced IH-7 bioflocculant showed better flocculation performance than PAC and IH-7 was significantly used to flocculate different types of suspended solids such as activated carbons, kaolin clays, soil solids, and yeast cells [9]. Moreover, bioflocculants are widely used for the recovery of suspended solids (SS) from wastewater treatment [10-12]. Bioflocculants are secondary metabolites produced during the growth of microorganisms such as bacteria, yeast and fungi that are composed of polysaccharides, proteins, lipids, glycoproteins, and glycolipids [13-15]. The composition and properties of coagulants depend on the type of flocculant-producing microorganisms (BPMs), composition of the media, and many conditions. The differences in the composition and properties of polysaccharides and proteins lead to differences in the charge of coagulant [16]. Culture conditions screening is a powerful approach to increase the production of extra polymeric substances from microorganism cultivation [17]. Although most flocculants can IIUM Engineering Journal, Vol. 19, No. 1, 2018 Jebun et al. 50 be used to flocculate kaolin suspension, they show different flocculating ability for other particles or colloids in aqueous solutions. Jebun et al. [18, 19] reported some filamentous fungi isolated from river water samples showed good entrapment potentiality to reduce turbidity from river water. Deng et al. [20] reported Aspergillus parasiticus produced a coagulant with high flocculating activity for kaolin suspension and water-soluble dyes. Pu et al. [21] reported that the compound coagulant produced by two strains of Rhizopus sp. was successfully used to reduce turbidity from potato starch wastewater. The same observation was made by Luvuyo et al. [22] for turbidity removal from kaolin clay by bioflocculant produced by a mixed culture of Methylobacterium sp. and Actinobacterium sp. In the present study, we examine the suitable culture conditions for the production of myco-flocculants by two novel L. squarrosulus RWF5 and S. obclavatum RWF6 for reducing turbidity from synthetic turbid water. The screening tests were conducted to find suitable nutrients, pH, nutrients concentration and inoculum size of these two potential fungi to enhance flocculation performance. In addition, stability of the single and compatible mixed culture supernatants (myco-flocculants) was investigated for chemical and environmental conditions to reduce turbidity by jar test. 2. MATERIALS AND METHODS 2.1 Microorganisms and Growth Conditions L. squarrosulus RWF5 and S. obclavatum RWF6 were isolated from river water samples collected from the River Pusu on the IIUM campus for coagulant production. L. squarrosulus RWF5 and S. obclavatum RWF6 cultures were maintained on potato dextrose agar (PDA) (Oxoid, UK) and initial pH was adjusted to 5.8±0.2. Distilled water was used to prepare medium solutions and sterilized at 121 oC for 20 minutes. The culture plates were incubated at 32±2 oC for 10 days. Subculture was conducted twice in a month and sub culture plates were stored at 25 oC in an incubator for further use. 2.2 Myco-coagulants Production 2.2.1 Screening of Nutrients The screening medium consisted of 5 g/l starch, sucrose, yeast extract, and malt extract and each of the medium was mixed with 1 liter of distilled water. The medium was then sterilized by autoclaving it at 121 °C for 15 minutes and then inoculated with 2% (v/v) fungal mycelial inoculum (340 mg/l). The liquid culture was then incubated in a rotary shaker with agitation at 150 rpm at 30± 2oC for 8 days. Initial pH of the broth was adjusted at 7.0 ± 0.1 using 1 M NaOH or 2 M HCl. Supernatants were taken at different time intervals to determine the flocculation activity. The effect of cultivation time for myco-flocculants production was investigated for 8 days. 2.2.2 Factors Affecting the Flocculating Rate To study the effect of malt extract concentration of 0-1% (g/l), initial pH values of 5, 6, 7, and 8, and inoculum doses of 1-4% on the flocculating rate were investigated. In this experiment, OFAT analysis was followed for three factors such as media concentration, pH, and inoculum dose. 2.2.3 Single and Mixed Culture The production medium consisting of 5 g/l malt extract was autoclaved at 121 °C for 15 minutes. The sterilized medium was inoculated with 2% (v/v) fungal inoculum for single IIUM Engineering Journal, Vol. 19, No. 1, 2018 Jebun et al. 51 and mixed culture (mycelium concentration of 340 mg/l). Ten day old culture plates were used to prepare fungal inoculum and the culture was incubated in a rotary shaker with 150 rpm at 30± 2 oC for 6 days. Initial pH of the culture was adjusted at 7.0±0.1 using 1 M NaOH or 2 M HCl. The cultures were harvested after 6 days of treatment and centrifuged to separate the biomass from supernatant (103 rpm for 10 mins at 25 oC). The supernatants were used as myco-flocculants and stored at room temperature at 28±2 oC for further use. 2.3 Myco-flocculant Stability 2.3.1 pH Stability of Supernatants The pH of myco-flocculants from single and mixed cultures was adjusted to 4, 5, 6, 7, and 8 with 1 M NaOH and 2 M HCl. A Jar test was conducted to observe flocculation activity in different pH. Initial turbidity and pH of kaolin suspension were recorded at 900±10 NTU and 7.0±0.1, respectively and the mixture was stirred at 120 rpm for 40 minutes and allowed to settle for 30 minutes. 2.3.2 Temperature Stability Myco-flocculants were treated at different temperatures of 4, 25, 35, 45 and 55 oC for 24 hours. Both supernatants were applied in kaolin suspension to reduce turbidity with the same conditions as referred to section 2.3.1. 2.3.3 Time Stability of L. squarrosulus Produced Myco-flocculant The myco-flocculant produced by L. squarrosulus RWF5 was tested for flocculation activity capability. The myco-flocculant was kept in room temperature (28±2 oC) and low temperature (4 oC) for 20 days. Jar tests were conducted to observe flocculation activity in terms of reducing turbidity from kaolin suspension. 2.3.3 Flocculation Activity Kaolin suspension was prepared using 0.7 g kaolin clay in 1 liter of tap water (turbidity 900±10 NTU). Each Jar contained 500 ml kaolin suspension was added with 1% supernatant (v/v). The jar apparatus was then operated at a speed of 120 rpm with 40 minutes mixing time and allowed to settle for 30 minutes [19]. Next, the top layer of water in each Jar was collected with a micro pipette and turbidity was measured with a portable turbidimeter 2100Q HACH, USA to measure residual turbidity. In the control experiment, 1% (v/v) of supernatant was replaced with 1% (v/v) of nutrient broth. The flocculating activity was calculated according to the following equation [23]. Flocculating activity (%) = [ 𝐴−𝐵 𝐴 ] × 100% (1) where, A is the initial turbidity value and B is the residual turbidity after flocculation. 3. RESULTS AND DISCUSSION 3.1 Myco-flocculant Production 3.1.1 Screening of Potential Nutrient Figure 1 (a) shows the flocculating activity of two coagulants for 6 days in media containing starch, sucrose, yeast extract, and malt extract. Starch, sucrose, and yeast extract were not favourable for L. squarrosulus and S. obclavatum growth, while the production of coagulants was relatively low when carbon and nitrogen sources were used separately. IIUM Engineering Journal, Vol. 19, No. 1, 2018 Jebun et al. 52 Fig. 1: The effects of nutrient and cultivation time on myco-flocculant production. a) Screening of potential nutrient, b) Culture time with malt extract. The highest myco-flocculant production from L. squarrosulus and S. obclavatum were obtained in malt extract media. Malt extract was used as co-substrate to enhance the separation and filtration process of treated sludge by fungal growth formation [24]. Aljuboori et al. [25], reported that the highest coagulant production by Aspergillus niger was observed when the C/N ratio increased up to 20/1 with a flocculating rate of 79% respectively, but that further increase in the C/N ratio slightly decreased the production. Figure 1 (b) shows the cultivation time with flocculation activity in terms of turbidity removal rate of myco-coagulants. The culture during the early stationary phase showed the highest (95% and 82% at 6 days) flocculating rate of L. squarrosulus and S. obclavatum, respectively. Results showed the flocculating rate decreased slowly after 6 days, suggesting these strains may be secreting deflocculation enzymes. A similar result was reported in the cultivation of A. parasiticus [20] and B. licheniformis [26]. Consequently, a period of 6 days was chosen as the culture time for the subsequent experiments. 3.1.2 Effect of Media Concentration, Initial pH, and Inoculum Size Figure 2 shows the effect of malt extract concentration on the flocculating rate of two myco-coagulants. L. squarrosulus and S. obclavatum increased myco-flocculants at 0.1% (w/v) and 0.25% concentration, respectively. The flocculating activity of two fungal strains was poor without malt extract concentration in the culture (0%). Small growth was found from the two fungal strains without nutrients (malt extract), suggesting that the strains may not able to secrete any metabolites due to lack of growth. 20 40 60 80 100 Starch Yeast extract Sucrose Malt extract T u rb id it y r e m o v a l (% ) Nutrients L. squrrosulus S. obclavatum 30 40 50 60 70 80 90 100 2 4 6 7 8 T u rb id it y R e m o v a l (% ) Cultivation Time (Day) L. squarrosulus S. obclavatum Control (a) (b) IIUM Engineering Journal, Vol. 19, No. 1, 2018 Jebun et al. 53 Fig. 2: Effect of media concentration of the flocculation activity on myco-flocculants. Figure 3 shows the effect of the initial pH of the culture medium on bio-coagulant production. The flocculating activity increased when pH was varied from 5 to 7 with the maximum flocculating activity of 95%. The removal rate (77%) decreased at an alkaline pH (8) for both of the cultures. Salehizadeh et al. [1] investigated that the initial pH of the production medium influences the electric charge of the cell and oxidation-reduction potential, which in turn affects the nutrient absorption and enzymatic reaction. Fig. 3: Effect of the initial pH of the culture medium on the flocculating activity of myco-flocculants. The flocculating rates obtained from the culture inoculated with 1 to 4% (v/v) inoculum size of two fungal strains are shown in Fig. 4. The use of 2 to 3% of L. squarrosulus inoculum dose in production medium recorded the highest flocculating rate of 96%. S. obclavatum was gradually decreased when inoculum dose was increased due to excessive overlapping of cells, resulting in inhibition of coagulant production. Aljuboori et al. [13] reported an optimal coagulant production by Aspergillus flavus at 2% (v/v) inoculum size, whereas a higher inoculum size of 10% (v/v) was most suitable for coagulant production by Rhizopus sp. [21] 30 40 50 60 70 80 90 100 0 1 2.5 5 7.5 10 T u rb id it y r e m o v a l (% ) Media concentration (g/l) L. squarrosulus S. obclavatum 50 60 70 80 90 100 5 6 7 8 T u rb id it y r e m o va l (% ) pH L. squarrosulus S. obclavatum IIUM Engineering Journal, Vol. 19, No. 1, 2018 Jebun et al. 54 Fig. 4: Effect of inoculum dose of culture medium on myco-flocculants production. 3.1.3 Compatible Mixed Culture Figure 5(A) shows ten day old single and mixed culture plates of L. squarrosulus and S. obclavatum. Figure 5(B) shows the turbidity removal (%) of single and mixed cultures. The flocculation rate was higher at 88% of mixed culture compared to the single culture of S. obclavatum (78%). The mixed culture showed significant growth of L. squarrosulus in the PDA plate, which indicated that the compatible mixed culture of L/S may have produced more substances to enhance flocculation to reduce turbidity compared to single S. obclavatum culture. Alam et al. [12] reported the fungal mixed culture of Aspergillus niger and Penicillium corylophilum was enhanced the separation process of wastewater sludge. Two strains of Rhizopus sp. produced a compound coagulant that was used to reduce turbidity of 91.1% from potato starch wastewater [21]. Fig. 5: Compatible mixed culture (A) L. squarrosulus (A-a), S. obclavatum (A-b), L. squarrosulus and S. obclavatum (L/S) front side of plate (A-c), L/S reverse side of plate (B) Turbidity removal by single and compatible mixed culture. 40 50 60 70 80 90 100 1 2 3 4 T u rb id it y r e m o v a l (% ) Inoculum dosage %(v/v) L. squarrosulus S. obclavatum 40 50 60 70 80 90 100 L. squarrosulus S. obclavatum Mixed culture Control T u rb id it y r e m o v a l (% ) LS LS L S a b c d (A) (B) IIUM Engineering Journal, Vol. 19, No. 1, 2018 Jebun et al. 55 3.1.4 Myco-coagulants Stability by Jar Test Figure 6(a) shows that L. squarrosulus was stable at a wide range, from pH 4.0 to 8.0 and more than 90% flocculation was achieved within this range. At pH 7.0, the turbidity removal rate was higher for both myco-coagulants and the flocculation rate decreased slowly as the pH increased further. The mixed culture also showed good stability at pH 7.0. Thus, these myco-coagulants are suitable to be applied at acidic and neutral conditions. This may be due to the fact that myco-flocculants show different electric charges at different pH levels and affect the flocculation ability of the bio-flocculant for kaolin particles [27]. Fig. 6: Myco-flocculant stability: a) The pH stability of L. squarrosulus, S. obclavatum and mixed culture; b) Temperature stability of L. squarrosulus, S. obclavatum and mixed culture; c) Time Stability of myco-flocculant (L. squarrosulus). 70 75 80 85 90 95 100 4 5 6 7 8 T u rb id it y r e m o va l (% ) pH L. squarrosulus S. obclavatum Mixed culture a 75 80 85 90 95 100 4 25 35 45 55 T u rb id it y r e m o va l (% ) Temperature (oC) L. squarrosulus S. obclavatum Mixed culture b 50 60 70 80 90 100 0 2 4 6 8 10 12 14 16 18 20 22 T u rb id it y r e m o va l (% ) Time (Day) 28±2 C 4 C c IIUM Engineering Journal, Vol. 19, No. 1, 2018 Jebun et al. 56 The effect of temperature on the flocculating activity of myco-flocculants was investigated (Fig. 6-b). The results showed that both myco-flocculants are fairly temperature-tolerant and had good flocculation activity at a wide range of temperatures. The flocculation ratio varied from 92% to 96% (L. squarrosulus) and 84% to 90% (S. obclavatum) in the temperature range of 4 oC to 55 oC, and only begins to decrease slightly with further temperature increase from 45 oC to 55 oC. The mixed myco-flocculant showed good stability at 4oC, then gradually decreased in temperature range to 45 oC -55 oC. The highest turbidity removal rate of 96% was observed at 25 oC and 35 oC for the L. squarrosulus myco-coagulant. These myco- flocculants were more stable at moderate temperatures (range 25 oC and 35 oC). Similar findings were observed by Aljuboori et al. [9], on the bioflocculant produced by Aspergillus flavus with a residual flocculating activity of about 93% at temperature range from 5 to 45 °C, thus indicating a thermostable bioflocculant. The result was similar to reported for the bioflocculant produced by Aspergillus parasiticus and it had moderate heat-stability [20]. Figure 6(c) shows the effect of time stability on turbidity removal rate of L. squarrosulus produced myco-flocculant. The highest turbidity removal % was recorded at room temperature (28±2 oC) till 12 days then it showed decreased flocculation activity of the myco-flocculant. This may be due to the fact that the metabolites of the myco-coagulant are deactivated gradually after two weeks of storage. However, turbidity removal rate was 85% at low temperature (4 oC) stored coagulant with 12 days. After two weeks, the flocculation activity was decreased gradually and it reached at about 50% at 20 days. This may have occurred due to the deactivation of metabolites. 4. CONCLUSIONS This study shows that L. squarrosulus and S. obclavatum produced myco-flocculants that were effective in the removal of turbidity of a kaolin suspension. The optimal conditions of L. squarrosulus myco-flocculant production were malt extract concentration 0.1% (g/l), initial pH 7.0 and inoculum dose 3% (v/v) for 6 day cultivation time which the flocculating activity reached above 95%. The two myco-flocculants’ stability indicates that they can work at different pH ranges between 4-8 and can be stored at room temperature (25 oC). Finally, both novel myco-coagulants are expected to be potential replacements of chemical coagulants and widely applied in water treatment and other industries. ACKNOWLEDGMENT The authors would like to express their thanks to Ministry of Higher Education (MOHE) for granting a Fundamental Research Grant Scheme (FRGS), project No. FRGS-14-109-0350 for the financial support. Thanks also to Research Management Centre (RMC), International Islamic University Malaysia for financial management and monitoring the progress of the project. REFERENCES [1] Salehizadeh H, Shojaosadati SA. (2001) Extracellular biopolymeric coagulants: recent trends and biotechnological importance. Biotechnology Advances, 19(5):371-385. [2] You Y, Ren N, Wang A, Ma F, Gao L, Peng Y, Lee D. (2008) Use of waste fermenting liquor to produce bioflocculants with isolated strains. International Journal of Hydrogen Energy, 33(13):3295-3301. IIUM Engineering Journal, Vol. 19, No. 1, 2018 Jebun et al. 57 [3] Prakash N B, Sockan V, Jayakaran P. (2014) Waste water treatment by coagulation and flocculation. International J. of Engineering Science and Innovative Technology, 3(2):479- 484. [4] Yan C, Le L, Yan-Hong G, Zi-Wen X. (2013) Characteristics analysis of different coagulants in the removal of organic matters of raw yellow river water. Information Technology Journal, 12(20):5746-5750. [5] Ruden C. (2004) Acrylamide and cancer risk- expert risk assessments and the public debate. Food and Chemical Toxicology, 42(3):335-349. [6] Yang YN, Ren N, Xue JM, Yang J, Rong BL. (2007) Mutation effect of MeV protons on bioflocculant bacteria Bacillus cereus. Nuclear Instruments and Methods in Physics Research Section B, 262:220–224. [7] Li Z, Zhong S, Lei HY, Chen RW, Yu Q, Li HL. (2009) Production of a novel bioflocculant by Bacillus licheniformis X14 and its application to low temperature drinking water treatment. Bioresource Technology,100(14):3650-3656. [8] Gong WX, Wang SG, Sun XF, Liu XW, Yue QY, Gao BY. (2008) Bioflocculant production by culture of Serratia ficaria and its application in wastewater treatment. Bioresource Technology, 99(11):4668-4674. [9] Aljuboori AH, Idris A, Al-joubory HH, Uemura Y, Abubakar BI. (2015) Flocculation behavior and mechanism of bioflocculant produced by Aspergillus flavus. Journal of Environmental Management. 150:466-71. [10] Gao Q, Zhu XH, Mu J, Zhang Y, Dong XW. (2009) Using Ruditapes philippinarum conglutination mud to produce bioflocculant and its applications in wastewater treatment. Bioresource Technology, 100(21):4996-5001. [11] Subramanian SB, Yan S, Tyagi RD, Surampalli RY. (2008) A new, pellet-forming fungal strain: its isolation, molecular identification, and performance for simultaneous sludge-solids reduction, flocculation, and dewatering. Water Environment Research, 80(9):840-852. [12] Alam MZ, Fakhru’l-Razi A. (2003) Enhanced settleability and dewaterability of fungal treated domestic wastewater sludge by liquid state bioconversion process. Water research, 37(5):1118-1124. [13] Aljuboori AH, Idris A, Abdullah N, Mohamad R. (2013) Production and characterization of a bioflocculant produced by Aspergillus flavus. Bioresource Technology,12:489-493. [14] More TT, Yadav JS, Yan S, Tyagi RD, Surampalli RY. (2014) Extracellular polymeric substances of bacteria and their potential environmental applications. Journal of Environmental Management, 144:1-25. [15] Okaiyeto K, Nwodo UU, Mabinya LV, Okoh AI. (2015) Bacillus toyonensis strain AEMREG6, a bacterium isolated from South African marine environment sediment samples produces a glycoprotein bioflocculant. Molecules, 20(3):5239-5259. [16] Subramanian SB, Yan S, Tyagi RD, Surampalli RY. (2010) Extracellular polymeric substances (EPS) producing bacterial strains of municipal wastewater sludge: isolation, molecular identification, EPS characterization and performance for sludge settling and dewatering. Water Research, 44(7):2253-2266. [17] Nwodo UU, Okoh AI. (2013) Characterization and flocculation properties of biopolymeric flocculant (Glycosaminoglycan) produced by Cellulomonas sp. Okoh. Journal of Applied Microbiology, 114(5):1325-37. [18] Jebun N, Al-Mamun A, Alam MZ, Karim MI, Raus RA. (2015) Evaluation of entrapment potentiality and turbidity removal efficiency of filamentous fungi. Jurnal Teknologi, 77(24):23-28. [19] Jebun N, Al-Mamun A, Alam MZ, Raus RA. (2016) Fungal Flocculants to Reduce Turbidity of River Water. ARPN Journal of Engineering and Applied Sciences, 11(6):4094-4099. [20] Deng S, Yu G, Ting Y. (2005) Production of a bioflocculant by Aspergillus parasiticus and its application in dye removal. Colloids and Surfaces B: Biointerfaces, 44(4):179-186. [21] Pu SY, Qin LL, Che JP, Zhang BR, Xu M. (2014) Preparation and application of a novel bioflocculant by two strains of Rhizopus sp. using potato starch wastewater as nutrilite. Bioresource Technology, 162:184-91. IIUM Engineering Journal, Vol. 19, No. 1, 2018 Jebun et al. 58 [22] Luvuyo N, Nwodo UU, Mabinya LV, Okoh AI. (2013) Studies on bioflocculant production by a mixed culture of Methylobacterium sp. Obi and Actinobacterium sp. Mayor. BMC biotechnology, 13(62):1-7. [23] Kurane R, Hatamochi K, Kakuno T, Kiyohara M, Hirano M, Taniguchi Y. (1994) Production of a bioflocculant by Rhodococcus erythropolis S-1 grown on alcohols. Bioscience, Biotechnology, and Biochemistry, 58(2):428-429. [24] Alam M, Fakhru'l-Razi A, Molla AH. (2004) Evaluation of fungal potentiality for bioconversion of domestic wastewater sludge. Journal of Environmental Sciences, 16(1):132- 137. [25] Aljuboori AH, Uemura Y, Osman NB, Yusup S. (2014) Production of a bioflocculant from Aspergillus niger using palm oil mill effluent as carbon source. Bioresource Technology, 171:66-70. [26] Shih I, Van Y, Yeh L, Lin H, Chang Y. (2001) Production of a biopolymer flocculant from Bacillus licheniformis and its flocculation properties. Bioresource Technology, 78(3):267- 272. [27] Pan Y, Shi B, Zhang Y. (2009) Research on flocculation property of bioflocculant PG.a21 Ca. Modern Applied Science, 3(6):106 - 112.