Iraqi Journal of Chemical and Petroleum Engineering Vol.9 No.4 (December 2008) 29-33 ISSN: 1997-4884 Study of the Performance of Batch Reactive Distillation Column Dr. Cecilia K. Haweel * and Taha M.A. Hamza ** * Chemical Engineering Department - College of Engineering - University of Baghdad – Iraq ** Ministry of Oil- Com. of North Refineries Abstract Batch reactive distillation was studied in packed bed column. Esterification of methanol with acetic acid to produce methyl acetate and water with homogenous sulfuric acid as a catalyst was considered. This system was chosen because the reaction is reversible and the boiling point of reactant and products are different. The reaction was carried out with and without distillation column and shows that the reactive distillation is more efficient from the conventional process (reactor and then separation). The conversion of acetic acid and concentration of methyl acetate increase by (30.43% and 75.14%) respectively at the best condition (reflux ratio 2, feed mole ratio 2 and batch time 90 minute). The influence of various parameters, such as batch time, reflux ratio, and feed mole ratio (methanol to acetic acid) on the performance of the batch reactive distillation column was studied, through the effect of the concentration of product and conversion of reactant. The results obtained for the non-ideal packed bed reactive batch distillation column show that the conversion of acetic acid is 90% at the best condition reflux ratio 2, feed mole ratio 2, and batch time 90 minute Introduction In recent years, increasing attention has been directed towards reactive distillation process as alternative to conventional processes (reactor and then separation). This has led to the development of a variety of techniques for reactive multistage column; however the problem of design and synthesis of batch reactive distillation processes have not yet been addressed [1]. Most of the distillation synthesis studies to date have been concerned with multi component non-ideal mixtures. The main advantages of this process relative to the conventional alternatives are the possibility of carrying equilibrium–limited chemical reaction to completion, and the simultaneous separation of the reaction products in only one unit .This reduces or eliminates reactor and recycle costs. This advantages of reactive distillation, and flexibility of a batch process can be combined in batch reactive distillation device, and the effect of operating parameter on yield and selectivity is studied [2]. The aim of the present work is to study the efficiency and the characteristics of the batch reactive distillation process and distinguished between it and the conventional reactor – distillation process. The present work provides a process for the production high purity methyl acetate from methanol and acetic acid, to study the effect of major variables (such as batch time, reflux ratio, and feed mole ratio) on the conversion of acetic acid and the concentration of methyl acetate in the product. Experimental Work A schematic sketch of the apparatus is illustrated in figure (1). It is comprised of all items, flask with two necks, one for the thermometer to measure the temperature at the still (vapor temperature) and the other connected to 3cm diameter and 57cm length distillation University of Baghdad College of Engineering Iraqi Journal of Chemical and Petroleum Engineering Study of the Performance of Batch Reactive Distillation Column IJCPE Vol.9 No. 4 (2008) 30 column. Packed with packing to a height of 30cm. The distillation column connected at the top with a thermometer to measure the top distillation temperature. The raising vapor from the distillation column was condensate by a condenser. The condense accumulates in the receiver which has two necks one for product through valve (1) and the other return back to the distillation column as reflux with fixed ratio (R) through valve (2). Dosing pump was used to control the quantity of the reflux to the distillation column. Heat was supplied to the still by electrical heater and was controlled on the temperature of the component in the still to desired value by using a variac. Fig. 1: Sketch of the experimental equipment Selection of Liquid- Liquid System The reaction of methyl acetate with acetic acid in the presence of sulfuric acid as homogenous catalyst to produced water and methyl acetate is: H2SO4 CH3COOH+CH3OH CH3COOCH3 + H2O Specification of Variables The variables considered for the present work are: a- Reflux ratio (0, 1, 2, and 3). b- Feed mole ratio (1, 1.5, 2, and 2.5) of methanol to acetic acid. c- Batch time (40, 60, 90, and 120 minute) These variables are studied and the results are compared with previous work. Results and Discussion Variable Effect on Product Concentration -Effect of Batch Time Figure (2) shows the relation between concentration of methyl acetate against time at variable feed mole ratio and constant reflux ratio (2). Form this figure it clear that the concentration of methyl acetate increase sharply up to (20) minute then it begin to increase slightly to value of (60) minute after that it remain constant, for a period of time depend on feed mole ratio and then decrease. At a low mole ratio along time is required for the concentration to be reduced because of the low mole ratio consist of high percent of acetic acid, methanol return to the still through the reflux and react with residual acetic acid to produce methyl acetate. For a high mole ratio, a short time is required for the concentration to be reduced. That mean a low percent of acetic acid which can be consumed rapidly and then concentration of methanol in the distillate will be increase to reduce the concentration of methyl acetate. Fig. 2: Concentration of methyl acetate vs. time at reflux ratio=2 and different feed mole ratio -Effect of Reflux Ratio Figure (3) shows the relation of methyl acetate concentration against reflux ratio for a batch time 90 minute and different feed mole ratio. This figure shows that the maximum concentration is at reflux ratio equal to (2) for all feed mole ratio except the value of feed mole ratio (2.5) where in this feed mole ratio the concentration increase directly mainly in straight line as it be explained previously. From this figure it can be deduced that the best reflux ratio is (2). V1 V2 TIME ( min) M E A C c o n c e n tr a ti o n (v o l. % ) 0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100 110 120 130 FMR=1 FMR=1.5 FMR=2 FMR=2.5 Dr. Cecilia K. Haweel and Taha M.A. Hamza 31 IJCPE Vol.9 No. 4 (2008) Fig. 3: concentration of methyl acetate vs. reflux ratio at 90 minute and different feed mole ratio. -Effect of Feed Mole Ratio Figure (4) show the concentration of methyl acetate against feed mole ratio at variable reflux ratio and constant time. The figures represented that if the mole ratio increase the concentration will decrease, because of if the percent of methanol increase in feed, it will vaporize more than methyl acetate, causes decrease of methyl acetate concentration. Fig.4: concentration of methyl acetate V.s. feed mole ratio at 90 minute and different reflux ratio Variable Effect on Conversion of Acetic Acid - Effect of batch Time Figure (5) shows the conversion of acetic acid against batch time for variable feed mole ratio and constant reflux ratio 2. this figure shows that the conversion of acetic acid increase slightly up to (60) minute then increase sharply up to the (120) minute as an over all the conversion of acetic acid increase with time due to the increase of consumption of acetic acid with time which cause a high conversion value. Fig.5: conversion of acetic acid V.s. time at R=2 and different feed mole ratio. - Effect of reflux ratio Figure (6) shows the conversion against reflux ratio at constant batch time 90 minute and different feed mole ratio. From this figure the conversion of acetic acid increase with reflux ratio up to reflux rate (2) and then decrease for all value of feed mole ratio, except for feed mole ratio (2.5) which shows a maximum value of conversion at reflux ratio equal to(1) this is in agreement with (Kai 6 , Agreda 7 , and Doherty 8 ). This is because of at increase reflux ratio, the distillate is rich in methyl acetate and when it return to the still, the reversible reaction is occurred and more acetic acid is produced which causes a decrease in the conversion of acetic acid. Fig. 6: conversion of acetic acid V.s. reflux at 90 minute and different feed mole ratio REFLUX M E A C c o n c e n tr a ti o n (v o l. % ) 58 64 70 76 82 88 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FMR=1 FMR=1.5 FMR=2 FMR=2.5 FEED MOLE RATIO M E A C c o n ce n tr a ti o n ( vo l. % ) 35 45 55 65 75 85 95 0.8 1.2 1.6 2.0 2.4 2.8 R=0 R=1 R=2 R=3 R= TIM E(min) C O N V E R S IO N 60 65 70 75 80 85 90 95 100 30 50 70 90 110 130 FM R=1 FM R=1.5 FM R=2 FM R=2.5 REFLUX C O N V E R S IO N 60 64 68 72 76 80 84 88 92 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FMR=1 FMR=1.5 FMR=2 FMR=2.5 Study of the Performance of Batch Reactive Distillation Column IJCPE Vol.9 No. 4 (2008) 32 - Effect of feed mole ratio Figure (7) shows the conversion against feed mole ratio at batch time 90 minute and different reflux ratio. In the case of (0, 1) reflux ratio the conversion will increase when the mole ratio increase, because of the continues of with draw the desired product, the reaction is always to foreword and cause consumption of the limited component (acetic acid), and increase it is conversion. If reflux ratio is increase to (2, 3) the conversion will increase with mole ratio up to (2) after that the conversion will decrease with increase of the feed mole ratio. That is because of low percent of methanol in feed, not all acid will react, so the conversion is low. As the percent of methanol in the feed increase to a limited amount the conversion increase, then it will decrease because of reversible reaction will occur. Fig.7: conversion of acetic acid VS. feed mole ratio at 90 minute and different reflux ratio. CONCLUSIONS From the present work the following conclusions are made: 1- The concentration of methyl acetate increase with increasing the reflux ratio to maximum value of reflux ratio equal (2) then decrease. 2- The concentration of methyl acetate increase with decrease feed mole ratio. 3- The concentration of methyl acetate increase with time to a limit value depending on the feed mole ratio. 4- The higher concentration of methyl acetate in thee product was obtained at reflux ratio 2, feed mole ratio 1, and for batch time 60 minute. 5- The conversion of acetic acid increase with feed mole ratio and reflux ratio to maximum value equal 2 then decrease. 6- The conversion of acetic acid increase with time. 7- The reactive distillation is more efficient than the conventional process at the best condition mentioned above for reactive distillation the conversion of acetic acid increase by 30.43% than that of conventional process, and the concentration of methyl acetate in the product increase by 75.14% than the conventional process. REFERENCE 1- Barabosa D. and Doherty, M. “The Simple Distillation of Homogeneous Reactive Mixture”, chem. Eng. Sci., Vol. 43, P. 541- 550, 1988. 2- Isao, S., Yagi, H., Komatsu, H. and Hirata, M. “calculation of Multi component Distillation Accompanied by Chemical reaction” Jour. Chem. Eng. Jap. Vol.4, P26-33, 1971. 3- Taylor R. and Krishna, R. “Modeling Reactive Distillation” Chem. Eng. Sci., Vol.55, P.5183-5229, 2000. 4- Towler, G.P. and Frey, S.J. (2000) Reactive Distillation, Chapter 2 in Reactive Separation. 5- kai Sundmacher “ Modren Methods in Heterogeneous Catalysis Research” Fritz Haber institute, Berlin, 14 November 2003. 7- Victor H. Agreda, Lee R.U.S. Patent 4435595 “Reactive Distillation Process for the Production of Methyl Acetate” 1984. 8- Doherty M.F., and M.F. Malone “Recent Advances in Reactive Distillation” AICHE Annual Meting, Dallas, paper203c, November 3, 1999. feed mole ratio c o n v e rs io n 55 60 65 70 75 80 85 90 95 0.8 1.2 1.6 2.0 2.4 2.8 R=0 R=3 R=2 R=1 R= Dr. Cecilia K. Haweel and Taha M.A. Hamza 33 IJCPE Vol.9 No. 4 (2008) دراسة اداءعمود التقطير التفاعلي ٔانُظاو انًسحخذو ْٕ جفاعم انًٍثإَل يع حايض انخهٍك , جى دساسة انحقطٍش انحفاعهً رٔ انذفعات فً عًٕد رٔ حشٕات ٔجى اخحٍاس ْزا انحفاعم الٌ انحفاعم عكسً ٔدسخات انغهٍاٌ , الَحاج خالت انًثٍم ٔانًاء بٕخٕد حايض انكبشٌحٍك كعايم يساعذ . نهًٕاد انًحفاعهّ ٔانُاجدّ يحباعذِ انحفاعم نٕحذِ )جى انعًم بٓزا انُظاو بٕخٕد أ عذو ٔخٕد عًٕد انحقطٍش ٔجبٍٍ اٌ انحقطٍش انحفاعهً اكفأ يٍ انطشٌقّ انعادٌّ عهى ( 75.14% ٔ 30.43)%حٍث اٌ َسبّ انححٕل نحايض انخهٍك ٔانحشكٍض نخالت انًثٍم جضٌذ بًقذاس . (ٔانحقطٍش نٕحذِ . ( دقٍق90ّ ٔصيٍ 2 َٔسبّ انًٕاد انًحفاعهّ 2عُذ ساخع )انحٕانً عُذ افضم انظشٔف جى دساسّ جاثٍش انعذٌذ يٍ انًحغٍشات يُٓا َسبّ انشاخع َٔسب انًٕاد انًحفاعهّ ٔجاثٍش انضيٍ عهى اداء بشج انحقطٍش رٔ انذفعات انًصاحب نهحفاعم انكًٍٍأي خالل خشٌاٌ انسائم ٔانبخاس داخم انبشج ٔجاثٍشْا عهى جشكٍض انًٕاد انُاجدّ ٔجحٕل انًٕاد . انًحفاعهّ انُحائح انحً جى انحصٕل عهٍٓا نهخالئط انغٍش يثانٍّ ندٓاص انحقطٍش رٔ انذفعات انًصاحب نهحفاعم انكًٍٍأي كاَث َسبّ انححٕل . دقٍق90ّ ٔصيٍ 2 َٔسبّ انًٕاد انًحفاعهّ 2عُذيا جكٌٕ َسبّ انشاخع %90نحايض انخهٍك جسأي