Iraqi J Pharm Sci, Vol.29(1) 2020 Itraconazole floating microparticles DOI: https://doi.org/10.31351/vol29iss1pp236-246 236 Formulation and In-vitro Evaluation of Itraconazole Floating Microparticles Taha A. Basher*,1 and Entidhar J. Al-Akkam* *Department of Pharmaceutics, College of Pharmacy, University of Baghdad, Baghdad, Iraq. Abstract Itraconazole (ITZ) is an antifungal drug (BCSII) used for the treatment of local and systemic fungal infections. Furthermore, ITZ used as an antifungal prophylaxis for immunocompromised patients. The objective of the study is to overcome the two problems of low and pH dependent solubility of ITZ by its preparation as floating microparticles. Firstly, pH-dependent floating microparticles were prepared using oil in water solvent evaporation method, from which the best one (F7) selected as a best pH-dependent formula with composition of ITZ (200mg),EC (800mg), HPMC 15cps (200mg) and safflower oil (2ml) .Then, F7 was compared with the selected Relatively pH- independent ITZ floating microparticles formula with composition of ITZ(200mg), a first coat of HPMC15cps (200mg), a second coat of EC (800mg), HPMC 15cps (200mg) and safflower oil (2ml) which prepared by a dual coating solvent evaporation method using a first coat which provides relatively pH-independent solubility, while the second coat applied as a bouncy producing agents. Polyvinyl alcohol (PVA) was used as a surfactant in both cases. The prepared floating microparticles were subjected to various evaluation parameters such as yield percent, drug loading and drug entrapment efficiency (EE), particle size analysis, in- vitro bouncy, drug release, Fourier Transforms Infrared Spectroscopy (FTIR), Differential Scanning Calorimetry (DSC) and X-ray Diffractometry (XRD) studies. The selected relatively pH-independent formula (F16) has a particle size of 11.29 μm with a polydispersity index of 0.651, and the best pH-dependent formula (F7) has a particle size of 2.56 μm with PDI of 0.37. In vitro drug release per cent from the selected formula (F16) was 100 % at 10 hour (pH 1.2) while was 84% at 12 hour (pH1.2) for F7 (p > 0.05), 62 % at 12 hour (pH 3.7) for formula (F16) while was 22% at 12 hour (pH 3.7) for F7 (p < 0.05) , was 35 %at 12 hour (pH 6.8) from F16while, 7% at 12 hour (pH 6.8) from F7(p < 0.05). Therefore ITZ release from the selected formula (F16)is significantly better(p < 0.05) and the bouncy per cent of selected formula (F16) was 95% that was significantly better than bouncy percent of F7 that was 86 %( p < 0.05) in formula 16. InF7, %DL and %EE were 97% and 89%, respectively, while in F16 both %DL and %EE were 96%. FTIR results showed no change in the peaks of the ITZ microparticles functional group while XRD and DSC show change the physical state of ITZ which indicate conversion from crystalline to amorphous, which had better stability(F16). Thus, dual-coated floating microparticles (F16) appeared to be a promising approach to improve solubility at different pH values and prolong the release of the ITZ within the stomach that may increase its oral bioavailability. Keywords: Itraconazole, Hydroxypropylmethylcellulose 15cps, Eudragits S100, solvent evaporation method, microparticles العائمة االتروكانازول لجسيمات تصييغ وتقييم خارج الجسم *عكاملاانتظار جاسم و 1*،طه عبد القادر بشير . العراق بغداد، بغداد، جامعة الصيدلة، كلية ،الصيدالنيات فرع* الخالصة كوقاية ITZعالوة على ذلك ، يستخدم اتراكونازول هو دواء مضاد للفطريات يستخدم لعالج االلتهابات الفطرية الموضعية والجهازية. .مضادة للفطريات للمرضى الذين يعانون من نقص المناعة والذوبان في درجة الحموضة المعتمدة هما العامالن الرئيسيان المسؤوالن عن التوافر البيولوجي انخفاض القابلية للذوبان في الماء ة المنخفض عن طريق الفم. الهدف من الدراسة هو التغلب على هاتين المشكلتين من خالل صياغة االتراكونازول كجسيمات مجهرية عائمة مستقل الذوبان وإطالة أمد إطالق االتراكونازول والذي من الممكن ان يؤدي إلى زيادة التوافر الحيوي.نسبياً عن األس الهيدروجيني لزيادة قابلية 1Corresponding author E-mail: babantaha497@yahoo.com Received: 23/11/2019 Accepted: 25/1 /2020 Iraqi Journal of Pharmaceutical Science https://doi.org/10.31351/vol29iss1pp236-246 Iraqi J Pharm Sci, Vol.29(1) 2020 Itraconazole floating microparticles 237 نتج عنه نسبه اطالق ألنهصيغه كأفضل( 7) الصيغةأوالً ، تم إعداد الجسيمات الدقيقة العائمة المعتمدة على الرقم الهيدروجيني ،وتم اختيار المستقلة العائمة االتروكانازول جسيماتحضير ، ت (%86ساعه مقبول ) 12خالل العائمةساعه ونسبه الجسيمات 12( خالل %84دواء مقبول) كطبقة أولى توفر قابلية ذوبان مستقلة عن درجة HPMC15 cpsبطريقة تبخير مذيب الطالء المزدوج باستخدام الهيدروجينينسبيا عن االس كمثبت مساعد. PVAواستخدم العوم وزيت القرطم كعوامل توفر ECو HPMC15cpsنسبياً و pH)الحموضة) تلجسيماا على لمحملا جلعالا كمية، لمنتجةا يةولمايكرا تلجسيماا كمية جسيمات الدقيقة العائمة المحضرة التي تخضع لمعايير تقييم مختلفة ، مثلال ( ،FTIR) الحمراء تحت باألشعة للطيف فورييه تحويل والدواء ، وتحرر( ، وتحليل حجم الجسيمات ، ، DEEالدواء ) انحسار، وكفاءة يةولمايكرا (.XRD) السينية األشعة حيود و( DSC) التبايني المسح مسعر 0.651ميكرون مع مؤشر متعدد االختالفات يبلغ 11.29على حجم جسيم يبلغ (F16) تحتوي الصيغة المحددة المستقل نسبيًا عن األس الهيدروجيني كان (F16) نسبه تحرر الدواء من الصيغة المحددة .PDI 0.37 .مع 2.56لها حجم جسيم (F7) ، وأفضل صيغة تعتمد على األس الهيدروجيني ساعات 12٪ خالل F7 ،62(P> 0.05) من (pH1.2) ساعات 12٪ خالل 84( بينما كان 1.2ساعات )درجة الحموضة 10٪ خالل 100 ساعات 12٪ خالل 35، وكان F7(p <.05) نم (pH 3.7) ساعات 12٪ في 22بينما كان (F16) ( من الصيغة المحددة3.7)درجة الحموضة (pH 6.8) ، ساعة 12٪ في 7بينما (pH 6.8) F7 (p <.05) وبالتالي فإن تحرر ، ITZ من الصيغة المحددة أفضل بكثير (p <.05). بلغت نسبة .٪95كانت F16 وفيF7٪86الكريات المايكرويه الطافيه تغيير الحالة الفيزيائية لـ DSC و XRD ، بينما أظهرت ITZ الوظيفية للجزيئات الدقيقة من أي تغيير في موقف المجموعة FTIR لم تظهر نتائج ITZ من البلورية إلى غير المتبلورة والتي كانت تتمتع بثبات أفضل مما قد يزيد من التوافر ITZطالق وهكذا ، يبدو أن الجسيمات الدقيقة العائمة المزدوجة المغلفة هي طريقة واعدة لزيادة القابلية للذوبان وإطالة أمد إ البيولوجي عن طريق الفم. .طريقة تبخير المذيبات، الجسيمات الدقيقة , ,هايدروكسي بروبل مثيل سيليلوز ,اثيل سيليلوز : اتراكونازول ةالكلمات المفتاحي Introduction Oral drug administration is the most common route to get a systemic effect due to its numerous advantages like safety, noninvasive, painless, does not require assistance, more convenient for chronic drugs administration and the medicament not need to be sterile.(1)However, several factors can affect the oral bioavailability, including water solubility and pH-dependent solubility. Hence, several techniques have been used to overcome these challenges include a reduction of the particle size that solves just water solubility problem(not the pH-dependent problem) such as micronisation or nanonisation, use of surfactants and conversion of crystalline to amorphous forms(2). Oil in water solvent evaporation method is most straight forward method for microencapsulation, widely used in pharmaceutical industries and cost- effective. This directly modified technique can be used to overcome many drugs physicochemical problems including both water solubility and pH- dependent solubility using specific coating materials (3). Microparticles defined as solid particles with range of 1 and 1000 μm in diameter consisting of a core (drug) and coat layer prepared using one of the microencapsulation methods to overcome core (drug) related undesired physicochemical properties to obtain a more therapeutically effective drug(4). Itraconazole is an active triazole, antifungal agent (C35H38Cl2N8O4), which is active against a broad spectrum of fungal species including 𝘊𝘳𝘺𝘱𝘵𝘰𝘤𝘰𝘤𝘤𝘶𝘴, 𝘊𝘢𝘯𝘥𝘪𝘥𝘢, 𝘈𝘴𝘱𝘦𝘳𝘨𝘪𝘭𝘭𝘶𝘴, 𝘉𝘭𝘢𝘴𝘵𝘰𝘮𝘺𝘤𝘦𝘴 and 𝘏𝘪𝘴𝘵𝘰𝘱𝘭𝘢𝘴𝘮𝘢 𝘤𝘢𝘱𝘴𝘶𝘭𝘢𝘵𝘶𝘮. (5, 6) Itraconazole is (BCS II) and has a pKa of 3.7 (7). ITZ has the characteristic of pH-dependent solubility having the highest solubility at the acidic media (4μg/ml) compared to basic pH (1μg/ml). It is slightly soluble in alcohols and freely soluble in dichloromethane and practically insoluble in water (8), indicating that low aqueous solubility and pH- dependent solubility are the main reasons for low oral bioavailability. Itraconazole is a weak basic drug with Pka of (3.7), therefore at a low pH, of gastric juice, ITZ will be ionised therefore, the gastric acidity is essential for adequate dissolution, and its oral bioavailability increased when taken with food since gastric pH decrease after food intake(9).However, Firstly the pH of the stomach is variable and impossible to remain below1.2 value, secondly there are cases that raise stomach pH value thus lead to decrease of ITZ solubility, and therefore bioavailability include fasting state, patients taking gastric acid-reducing agents such as protein pump inhibitors(PPI) and H2-blockers and Furthermore patients with AIDS who complain from Hypochlorhydria.(10). The objective of this study is to overcome both low water solubility and pH-dependent solubility of Itraconazole by formulating it as floating microparticles and one with a relatively pH- independent floating microparticles and compared between them thus to improve the solubility at variable pH values and prolong the release of the ITZ in stomach, which may lead to increase in ITZ bioavailability. Materials and Methods Materials Itraconazole (ITZ) powder (Baji Gaokang Bio- Technology Co., Ltd., China), Hydroxy propylmethylcellulose (HPMC15cps)(Shanghai Ruizheng chemical Tech Co., Ltd., China),Ethylcellulose (EC)(BDH Chemical Ltd., England),Extra virgin olive oil (EVOO), Rice bran oil (RBO), Palm oil (PO) and safflower oil (SFO) (Furkan Dogalurunler.TIC.SAN.LTD, Turkey). Dichloromethane (DCM) (Thomas Baker Chemicals PVT.Ltd., India), Ethanol, methanol and n-hexane (Chem-LabNV.,Belgium). Hydrochloric acid (HCL) (Central Drug House (P) Ltd., India). Eudragit S100 (ED S100) (ATHOS CHEMICALS, Co., Ltd., India). Methods Saturation solubility determination Solubility studies for the pure drug achieved in 0.1N HCl (pH1.2), HCl buffer (pH 3.7) and phosphate buffer (pH 6.8) alone and with SLS at a concentration of 2, 3 and 6% (w/v), respectively. Iraqi J Pharm Sci, Vol.29(1) 2020 Itraconazole floating microparticles 238 Excess amount of pure ITZ was added to 10 ml of each solution in a test tube and agitated at 25±0.5°C in a rotary test tube shaker for 72hr. Then, samples were filtered using 0.45µm Millipore filters. Each filtrate suitably was diluted with the respective solvent and analyzed by measuring the absorbance at the determined maximum wavelength (λmax) in each solvent usingUV-1800 UV-Vis Spectrophotometer (Shimadzu Scientific Instruments Inc., Japan).The solubility (mg/ml) of ITZ was calculated (11). Preparation of ITZ floating microparticles (pH- dependent) Oil in water solvent evaporation method was used to prepare floating microparticles (pH- dependent) of ITZ. Fifteen formulas prepared using different concentrations of polymers including; EC,HPMC 15cps and ED S100. Different oils were also used such as; Extravirigin olive oil (EVOO), Rice bran oil (RBO), palm oil (PO) and safflower oil (SFO). Polyvinyl alcohol (PVA) was used as a surfactant, as shown in table (1). The vegetable oils were not used in formulas F1-F3. The used oils dissolved in a vehicle composed of (DCM) and ethanol at 1:1 ratio forming the oil phase to which the drug added. While the aqueous phase containing 0.75% PVA as a surfactant. The oil phase was added to the aqueous phase drop wise using a bared syringe, under high- speed mechanical agitation of 1000rpm by utilizing magnetic stirrer for one hour at 25±1°C to allow the organic solvent to evaporate and get the microparticles that filtered and dried at room temp overnight. Each formula was washed with 5 ml DCM to remove the excess oil if needed and dried again (12). Table 1.Composition of ITZ floating microparticles (pH-Dependent) Ingredient Formula no. F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 ITZ(mg) 200 200 200 200 200 200 200 200 200 300 200 200 200 200 200 EC(mg) 900 800 700 800 800 800 800 700 900 800 800 800 - 800 800 HPMC15 CPS(mg) 100 200 300 200 200 200 200 300 100 200 200 200 200 200 200 EDS100 (mg) 800 EVOO (ml) 2 RBO (ml) 2 PO(ml) 2 SFO(ml) 2 2 2 2 1 2 2 2 2 Ethanol (ml) 20 20 20 20 20 20 20 20 20 20 20 20 20 20 Methanol (ml) 20 DCM (ml) 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 DW(ml) 400 400 400 400 400 400 400 400 400 400 400 200 400 400 400 PVA(%) 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 Speed(rpm) 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 500 1000 Iraqi J Pharm Sci, Vol.29(1) 2020 Itraconazole floating microparticles 239 Preparation of relatively pH-independent ITZ floating microparticles Dual coating solvent evaporation method used for the development of the relatively pH- independent ITZ floating microparticles. The first coat composed of HPMC 15 cps. It was applied by using oil in water solvent evaporation method then without filtration the second coat was an organic solution of HPMC15, EC and SFO in 1:1 of DCM: ethanol as a solvent(13) as represented in table 2. Table2. Composition of ITZ relatively pH- independent floating microparticles Ingredient F 16 ITZ (mg) 200 1st coat 2nd coat HPMC15 CPS (mg 200 DCM (ml) 10 Ethanol (ml) 10 EC (mg) 800 HPMC15 CPS (mg) 200 SFO (ml) 2 Ethanol (ml) 20 DCM (ml) 20 DW (ml) 400 Speed (rpm) 1000 1000 Characterization of the prepared floating microparticles Percentage yield determination Yield of the prepared microparticles calculated by dividing the dry weight of the prepared microparticles (practical weight) by the total weight of the drug and excipients used (theoretical weight) as stated in the following equation: 𝑌𝑖𝑒𝑙𝑑 (%) = (𝐴𝑐𝑡𝑢𝑎𝑙 𝑤𝑒𝑖𝑔ℎ𝑡/𝑡ℎ𝑒𝑜𝑟𝑒𝑡𝑖𝑐𝑎𝑙 𝑤𝑒𝑖𝑔ℎ𝑡) ×100 (1) Particle size and polydispersity index (PDI) determination All of the prepared formulations were in the micro size that is bellow 212μm because all are sieved using sieve number 70. In addition , particle size and PDI of the prepared ITZ floating microparticles F7,F12, F14,F15 and F16 measured by dynamic light scattering (DLS) using Nano Brook 90Plus particle size analyzer (Brookhaven instruments. the USA). Measurements were performed in triplicate by measuring the intensity of light scattered by the molecules in the sample as a function of time at 90° scattering angle and constant temperature 25 °C. The PDI was determined, which measured the width of the size distribution of each formula; it is an index of spread or variation within the particle size (14). Drug loading and entrapment efficiency (EE) determination 25 mg of each formula dissolved in 50 ml methanol. The solution filtered by 0.45 µm Millipore filters and 1 ml was taken and diluted with methanol if required. The samples were analyzed for drug content spectrophotometricaly at 262 nm (14). EE (%) = (Actual drug loading / theoretical drug loading) ×100 (2) Drug loading (%) =(Actual drug content / Weight of powdered microsphere) ×100 (3) Buoyancy per cent determination Weight of the formula equivalent to 100mg ITZ was spread over the test media using dissolution apparatus (type II) that filled with 900 ml of 0.1N HCl (pH 1.2, pH 3.7) and phosphate buffer (pH 6.8) separately in each case. The medium was agitated with a paddle rotating at 50 rpm for 12 h. both floating time (FT) and floating lag time were calculated. The floating and the settled portions of microspheres recovered separately were dried and weighed. All the bouncy studies were performed in duplicate (14) Bouncy % = (Wf / Wf + Ws)×100 (3) In- vitro release studies All formulations were subjected to in- vitro release studies. The studies were carried out by USP apparatus II (paddle method) at 50 rpm using 900 ml of 0.1N HCL (pH 1.2, pH 3.7) and phosphate buffer (pH 6.8). The temperature maintained at 37 ± 0.5 °C. At specific time intervals (every two hours), five ml aliquots were withdrawn and analyzed by UV spectrophotometer at the respective λmax after suitable dilution against suitable blank. The removed volume replaced with an equal volume of fresh solvent (9). All release studies performed in duplicate. (14) Differential scanning calorimetry (DSC) The DSC of pure ITZ powder and selected formula (F16) was taken on (Shimadzu DSC-60 plus, Japan).Ten milligrams sealed in the flat- bottomed aluminum pan of the differential scanning calorimeter. Data collection was achieved at a temperature range of 25–200°C and the heating rate was 5°C/min under nitrogen gas at a flow rate of 25 ml/min (15). Fourier transform infrared spectroscopy (FTIR) analysis The FTIR spectra of pure ITZ and selected formula were recorded using FTIR -7600, Iraqi J Pharm Sci, Vol.29(1) 2020 Itraconazole floating microparticles 240 Australia spectrophotometer. Powders were mixed with potassium bromide and compressed into disks using hydraulic press before scanning from 4000 to 400 cm-1 (16). X-ray powder diffractometry study The XRD patterns for pure ITZ and selected formula (F16) were analyzed using an XRD- 6000, Shimadzu-Japan. The sample chosen scanning was conducted over powder X-ray diffractometer at the axis of 2 thetas, with the continuous scan range of 5-80 degree. The operating voltage was 40 kV and current 30mA and scans step size of 0.050° (2θ) and scan step time of 60 seconds (17). Statistical analysis To investigate the significance of the difference between the results of studied formulations, T-test used. The level of significance set at a  0.05, and (P <0.05) was considered to be statistically significant. Results and Discussion Saturation solubility of pure ITZ The saturated solubility of ITZ were 0.1, 0.01 and 0.0044 in 0.1N HCl (pH 1.2), HCL buffer (pH3.7) and phosphate buffer for (pH 6.8), respectively as shown in Fig (1). Since Sodium lauryl sulfate (SLS) is a surfactant, so it used to increase the solubility of ITZ to fulfill sink condition. The saturated solubility of ITZ were 0.42, 0.37 and 0.36 at 0.1N HCl (pH1.2with2% SLS), (pH3.7with3% SLS) and phosphate buffer of pH 6.8 with 6% SLS. Figure 1. Saturated solubility of pure ITZ at different pH. Percentage yield The yield per cent of various floating microparticles formulas prepared depicted in figure (2).Per cent yield does not reach 100% usually due to mechanical variables during preparation method and precipitation of the formula components on the tools used in the preparation. The percent yield was 58% in F2 were no vegetable oils used. However, the use of vegetable oils results in significant increase in yield per cent, F4 98%, F5 95%, and F6 91%, F7 86% were different vegetable oils used (p < .05). Also, the higher SFO volume (F7 two ml versus one ml in F11) result in the higher per cent yield ( F7 92% and F11 88%) may be due to the higher oleic acid content when higher volume used. In F16, the lower yield was due to the longer stirring time that is three hours compared to one hour in F7 (different method was used). (18) Similarly, the lower HPMC15 cps concentration results in a higher yield per cent, in F8 were 300mg of HPMC and 700 mg of EC the yield was 83% while in F9 were 100mg of HPMC and 900 mg of EC used a yield of 98%. This result may be due to increasing HPMC 15cps concentration result in a higher viscosity of the oil phase which results in flocculation and agglomeration of the prepared microparticles thus lower yield per cent. Nepal et al. had found that the higher polymer concentration, the higher yield percent until an certain value after which the yield decreased (12). Figure 2. Percentage yield of ITZ floating microparticles. Particle size analysis All the prepared formulations were in the micro size bellow 212μm because all are sieved using sieve number 70. However, F7, F12, F14, F15 and F16 particle size determined using, dynamic light scattering (DLS) by Nano Brook 90Plus particle size analyzer, and their particle size varied from 2.56µm to 6.086µm as shown in figure 3.the higher stirring rate; the smaller microparticles size due to less tendency of the formed microparticles to coalescence and aggregate (18,19). Regarding the (F16), the particle size is bigger due to the higher drug-to- polymer ratio and the longer stirring time (20). Figure 3. Particle size (μm) of ITZ floating microparticles Iraqi J Pharm Sci, Vol.29(1) 2020 Itraconazole floating microparticles 241 Drug loading and entrapment efficiency (EE) determination The results of drug loading (DL) and drug entrapment efficiency (EE) have been shown in figure (4) and figure (5), respectively. InF4, F5, F6, F7, the %DL was 98, 98, 92 and 97%, respectively, and %EE was 98, 97, 84 and 89%, respectively while in F1, F2 and F3 the %DL was range from 50-79 and %EE range from 20- 46.Using vegetable oils results in a significant increase in both drug loading and entrapment +efficiency (p < 0.05).Vegetable oil with higher oleic acid content results in higher DL and EE (F4). Similarly, these parameters increase upon using of lower concentration of HPMC15cps; in F8 were 300 mg of HPMC15cps used, %DL was 86, and EE was 71 while in F9 were 100mg of HPMC15cps used %DL was 99 and %EE was 98.The preparation technique dual coating solvent evaporation method also results in higher DL and EE (21). Figure 4. Drug loading of ITZ floating microparticles Figure 5. Entrapment efficiency of ITZ floating microparticles. Buoyancy percent The floating lag time (FLT) was zero for all formulas since floating has occurred immediately after the formula spread over the test media (23). The floating time (FT) was range from 3 %( F3) to 98 %( F4) as shown in Fig (6).Vegetable oils used were the key factor that provides bouncy; with higher oleic acid content of the vegetable oil; higher bouncy per cent obtained so in (F4) EVOO used that had the highest oleic acid content among the used vegetable oil resulting highest bouncy per cent (94%). Also, the concentration of HPMC15cps played an essential role in the determination of bouncy per cent with the lower the HPMC14cps concentration, the higher bouncy per cent (95% in F9). Floating ability result from the low density of the prepared microparticles . Similar results observed with floating microparticles of resperidone (12). Figure 6. Bouncy percent of ITZ floating microparticles In vitro drug release In vitro cumulative release per cent from the selected formula (F16) was 100 % at 10 hour (pH 1.2) while was 84% at 12 hour (pH1.2) from F7 (p> 0.05), 62 % at 12 hour (pH 3.7) from selected formula(F16) while was 22% at 12 hour (pH 3.7) from F7 (p < 0.05) , was 35 %at 12 hour (pH 6.8) while, 7% at 12 hour (pH 6.8) from F7(p < 0.05), therefore ITZ release from the selected formula is significantly better(p < 0.05)as shown in figures (7) and (8). These results indicated the efficiency of the dual coating solvent evaporation method and the pH-independent polymers used in solving the problem of the pH-dependent release of Itraconazole. Furthermore, since, Itraconazole is BSCII drug thus decreasing the particle size to micro-scale resulted in higher solubility this coordinated with Noyes–Whitney equation, in which the dissolution rate enhanced as the saturation solubility increased and the particle size decreased .Also, relatively pH-independent solubility advantage resulted from the first coat, namely HPMC 15cps(13,22,23). Another factor that may contribute to the fast release was the entrapment efficiency which had a direct effect on the drug release profile. As it increased, the release rate also increased (24). Iraqi J Pharm Sci, Vol.29(1) 2020 Itraconazole floating microparticles 242 Figure 7. Release profile for pH-dependent ITZ floating microparticles at various pH. Figure 8. Release profile for relatively pH- independent ITZ floating microparticles at various pH. Differential scanning calorimetry (DSC) The DSC was used to estimate the effect of excipients and conditions on the physical properties of the drug. Pure ITZ exhibited a sharp endothermic melting peak at 170° (Figure 9) indicating no change in its melting temperature and the drug had a crystalline nature with high purity. The DSC of the selected formula (F16) in figure 10 showed the complete disappearance of the melting peak of ITZ gave clear evidence of the transformation of the drug from crystalline to the amorphous state (25, 26). Figure 9. DSC thermogram of pure ITZ at temperature range (20-250 °C) Figure 10. DSC thermogram of selected formula (16) at temperature range (20-250 °C) Fourier transforms infrared spectroscopy (FTIR) The FTIR spectrum of pure ITZ shown in figure 11. The main peaks of pure ITZ observed at wavenumbers,3466, 3130, 2965, 3067, 1698, 2822,1611, 1512 and 1453cm-1. It should be noted that all the characteristic bands of ITZ were detected in the spectrum of the physical mixture of drug, EC, HPMC15cps, as shown in figure 12. Therefore, there is no interaction between the drug and polymers used. A sharp band at 1698 cm−1 in the pure drug spectrum was due to C= O, in the FTIR spectrum of the selected formula (F16) all of the ITZ characteristic peaks are present as shown in figure 13 excepted that, the peak 1698 that shifted to 1745 this is because the fatty acids content of safflower oil has a characteristic peak at 1745 that shown in figure 14 (27) thus, in conclusion, the drug, polymers and safflower oil used in the formulation were compatible with each other.( 28,29). Figure 11. FTIR spectrum of pure ITZ. Iraqi J Pharm Sci, Vol.29(1) 2020 Itraconazole floating microparticles 243 Figure 12. FTIR spectrum of the physical mixture of drug, EC and HPMC 15cps. Figure13.FTIR spectrum of floating microparticles (selected formula F16) Figure 14. FTIR spectrum of safflower oil. (27) Powder X-ray diffraction (PXRD) XRD test of the pure drug and the selected formula (F16) was done to detect the polymorphic structure of the drug before and after formulation. Generally, the amorphous mater sate has higher physical stability. Crystalline nature of pure ITZ easily detected through the numerous distinctive peaks as shown in figure 15 (27).The XRD of F7 and F16 showed disappearance of the characteristic peaks of pure ITZ as shown in figure 16 and 17 indicated that ITZ incorporated into the polymer matrix that was in the amorphous state (30). Iraqi J Pharm Sci, Vol.29(1) 2020 Itraconazole floating microparticles 244 Figure 15. XRD of pure ITZ. Figure 16.XRD of ITZ selected formula (F16) Figure 17. XRD of ITZ best pH-dependent formula ( F7) Conclusion Dual coating solvent evaporation method was successfully used to produce relatively pH-independent ITZ floating microparticles by using the pH-independent water-soluble polymer(HPMC15 cps) that provided relatively pH-independent solubility of ITZ with a hydrophobic polymer (EC) and safflower oil that provided bouncy. Different parameters, such as HPMC 15cps versus EC concentration, various vegetable oil including, safflower oil volume, stirring speed, oil to water ratio, co solvent type, drug- to - polymer ratio were investigated and optimized to produce a formula that provided both excellent bouncy for 12 hours with maximum drug release. PH-independent ITZ floating Iraqi J Pharm Sci, Vol.29(1) 2020 Itraconazole floating microparticles 245 microparticles (F16) was significantly better than PH-dependent ITZ floating microparticles (F7) in both bouncy per cent at 12 hours and dissolution profile at all test media of different pH values (p < .05), therefore, Dual coating solvent evaporation method is a promising method to improve pH-dependent and solubility problems of ITZ. References 1. Tripathi KD. Essentials of Medical Pharmacology. 6th edition. New Delhi: Jitendar P Vij Jaypee Brothers Medical Publishers (P) Ltd; 2013. 2. George M, Ghosh I. Identifying the correlation between drug/stabilizer properties and critical quality attributes (CQAs) of the nanosuspension formulation prepared by wet media milling technology. European Journal of Pharmaceutical Sciences. 2013;48(1-2):142-52. 3. Li M, Rouaud O, Poncelet D.Microencapsulation by solvent evaporation: State of the art for process engineering approaches.Int. J. Pharm.2008;363(1-2):26-39 · 4. Wong CY1, Al-Salami H1, Dass CR2.Microparticles, microcapsules and microspheres: A review of recent developments and prospects for oral delivery of insulin. Int J Pharm. 2018; 537(1-2):223-44. 5. Virginia FU, Claudia CA, Giulio PE, Roberto AV, Daniele TI, Cesarina GI, et al. Biological properties of itraconazole-SLN . Biointerface Res. Appl. Chem.2018 ; 8 (5): 3624 – 27. 6. Martindale(The CompleteDrug Reference) .38ed. ,2014. P-583-85. 7. Pandey S. Itraconazole nanosuspension meant for oral use: development of formulation, characterisation and in vitro comparison with some marketed formulations.DerPharmacia Lettre. 2010;2:162-71. 8. Moffat AC, Osselton MD,Widdop B. Clarke's analysis of drugs and poisons.3rd ed. Pharmaceutical Press: London; 2004. 9. Kavitha VB, Neethu CS, Dineshkumar B, Krishnakumar K, John A. Nanosuspension formulation: An improved drug delivery system. Nanosci Nanotechnol Int J. 2014;4:1-5. 10. Bae SK, Park SK, Shim EG, Mun JH, Kim EU, Shin JG et al.Increased oral bioavailability of itraconazole and its active metabolite,7hydroxyitraconazole, when coadministered with a vitamin c beverage in healthy participants.J Clin. Pharm., 2011; 51:444-451 11. Shabada A, Prashanthi Y, Reddy CH, Vivekananda B. Formulation development and evaluation of hydrotropic solubilization based suspensions of Itraconazole. Indo American Journal of pharmaceutical sciences. 2017;4(11):4425-34. 12. Ammar HO, Ghorab MM, Mahmoud AA, Noshi SH.Formulation of risperidone in floating microparticles to alleviate its extrapyramidal side effects. Future J Pharmace Sci. 2016;2(2):43-59. 13. Grekhnyova EV, Kudryavtseva TN, Kometiani IB, Velyaev YO. Microencapsulation of furacilin as a method of creating new medicinal forms, possessing with increased biological accessibility and prolongable effect. Asian Journal of Pharmaceutics. 2017; 11 (4): S920 14. Gökbulut E, Vural I,Aşıkoğlu M,Özdemir N. Floating drug delivery system of itraconazole: Formulation, in vitro and in vivo studies. J Drug Deliv Sci Technol. 2019;49:491-501. 15. Pore YV, Shinde VR, Rao JV. Physical stabilisation of amorphous itraconazole in solid dispersions for improved dissolution profile. Journal of Applied Pharmaceutical Science. 2016;6(10):037-44. 16. Dolenc A, Govedarica B, Kocbek P, Srčič S, Kristl J. Nanosized particles of orlistat with enhanced in vitro dissolution rate and lipase inhibition. International journal of pharmaceutics. 2010;396(1-2):149-55 . 17. Jassim ZE, Hussein AA. Formulation and evaluation of clopidogrel tablet incorporating drug nanoparticles. IJPS. 2014:838-51. 18. Hendrawati TY, Rahman MIS, Nugrahani RA, Siswahyu A, Alvika Meta Sari. Microencapsulation techniques of herbal compounds for raw materials in food industry, cosmetics and pharmaceuticals [Internet]. IntechOpen. IntechOpen; 2019 [cited 2019Nov21]. Available from: https: / /www .intechopen .com / books / microencapsulation-processes- technologies – and - industrial- applications / microencapsulation- techniques-of-herbal-compounds for- raw- materials – in – food – industry - cosmetics-and-p. 19. Jelvehgari M, Nokhodchi A, Rezapour M, Valizadeh4 H.Effect of Formulation and processing variables on the characteristics of tolmetin microspheres prepared by double emulsion solvent diffusion method.Indian J Pharm Sci. 2010; 72(1): 72–78. Iraqi J Pharm Sci, Vol.29(1) 2020 Itraconazole floating microparticles 246 20. Jelvehgari M, Barar J, Nokhodchi ,A,Shadrou A, Valizadeh H.Effects of process variables on micrometric properties and drug release of non- degradable microparticles.Adv Pharm Bull.;2011; 1(1): 18–20-Rathod UC, Patel AK, Shah DA.Statistical Evaluation and optimization of influence of stirring speed and polymer concentration on hollow microspheres of diltiazem HCl. Der Pharmacia Lettre, 2012, 4 (3):972-978. 21. Dhakar RC, Maurya SD, Sagar BP, Bhagat S, Prajapati SK, Jain CP.variables Influencing the drug entrapment efficiency of microspheres: a pharmaceutical review. Der Pharmacia Lettre, 2010, 2(5): 102-116. 22. Wo2001085135a1 - Pharmaceutical composition containing itraconazole with gastric pH-Independently Improved Solubility and preparation method thereof [Internet]. Google Patents. Google; [cited 2019Oct25]. Available from: https://patents.google.com/patent/WO2 001085135A1/en. 23. Abbas HK, Wais FM, Abood AN. Preparation and evaluation of ketoprofen nanosuspension using solvent evaporation technique. Iraqi Journal of Pharmaceutical Sciences .2017; 25(4): 41-55. 24. Devara RA, Habibudin MO, Aukunuru JI. Enhancement of dissolution rate of poorly soluble drugs itraconazole by nanosuspension technology: its preparation and evaluation studies. Asian J Pharm Clin Res.2018; 11( 4): 414-421. 25. Ferreira PC1, Guimarães de Lima CS 2, Noronha LL 1, Moraes MC2, Silva FC 2, Viçosa AL 3, Futuro DO1 and Ferreira VF.Development of a Method for the quantification of clotrimazole and itraconazole and study of their stability in a new microemulsion for the treatment of sporotrichosis. molecules .2019;24 (33) :1-15 26. Pore YV, Shinde VR, Rao J. Physical stabilisation of amorphous itraconazole in solid dispersion for improvement of dissolution profile. J Appl. Pharm. Sci.2016;6 (10): 037-044.re write references according 27. University of Tartu Institue of chemistry. Database of ATR-FT-IR spectra of various materials [Internet].2015; [cited 2019Nov22]. Available from: http://lisa.chem.ut.ee/IR_spectra/paint/ binders/stand-oil-safflower/. 28. Ahuja M, Verma P, Bhatia M. Preparation and evaluation of chitosan– itraconazole coprecipitated nanosuspension for ocular delivery. Journal of Experimental Nanoscience. 2015;10(3):209. 29. Vyas PR, Patel KJ. Enhancement of solubility of Itraconazole using novel liquisolid technique. Pharma Science Monitor. 2015;6(2).269-286. 30. Wei Y, Ling Y, Su M, Qin L, Zhang J, Gao Y, Shuai Q. Characterization and stability of amorphous tadalafil and four crystalline polymorphs. Chem Pharm Bull. 2018;66(12):1114-1121. Baghdad Iraqi Journal Pharmaceutical Sciences by bijps is licensed under a Creative Commons Attribution 4.0 International License. Copyrights© 2015 College of Pharmacy - University of Baghdad. https://www.ncbi.nlm.nih.gov/pubmed/?term=Jelvehgari%20M%5BAuthor%5D&cauthor=true&cauthor_uid=24312752 https://www.ncbi.nlm.nih.gov/pubmed/?term=Barar%20J%5BAuthor%5D&cauthor=true&cauthor_uid=24312752 https://www.ncbi.nlm.nih.gov/pubmed/?term=Nokhodchi%20A%5BAuthor%5D&cauthor=true&cauthor_uid=24312752 https://www.ncbi.nlm.nih.gov/pubmed/?term=Shadrou%20S%5BAuthor%5D&cauthor=true&cauthor_uid=24312752 https://www.ncbi.nlm.nih.gov/pubmed/?term=Valizadeh%20H%5BAuthor%5D&cauthor=true&cauthor_uid=24312752 http://bijps.uobaghdad.edu.iq/index.php/bijps.com http://creativecommons.org/licenses/by/4.0/ http://creativecommons.org/licenses/by/4.0/ http://creativecommons.org/licenses/by/4.0/