{Electrocoagulation of whey acids: anode and cathode materials, electroactive area and polarization curves} doi:10.5599/jese.381 89 J. Electrochem. Sci. Eng. 7(2) (2017) 89-101; doi: 10.5599/jese.381 Open Access : : ISSN 1847-9286 www.jESE-online.org Original scientific paper Electrocoagulation of whey acids: anode and cathode materials, electroactive area and polarization curves Francisco Prieto-García1, Judith Callejas-Hernández1, Judith Prieto-Méndez2,, Yolanda Marmolejo-Santillán1 1Área Académica Química, Universidad Autónoma del Estado de Hidalgo. Carret. Pachuca- Tulancingo, km. 4.5, C. P. 42076. Mineral de la Reforma. Hidalgo. México 2Área Académica de Agronomía, Universidad Autónoma del Estado de Hidalgo. Carret. Pachuca- Tulancingo, km. 4.5, C. P. 42076. Mineral de la Reforma. Hidalgo. México Corresponding author: jud_292003@yahoo.com.mx Received: March 30, 2017; Revised: June 6, 2017; Accepted: June 6, 2017 Abstract Anode (Al and Fe) and cathode (graphite and Ti/RuO2) materials have been tested for electrocoagulation (EC) and purification of the acid whey. The electroactive areas (EA) of electrodes were calculated by the double layer capacitance method. Experiments were performed by cyclic voltammetry, chronoamperometry and polarization experiments. Among cathodic materials, the Ti/RuO2 electrode showed higher EA (2167 cm2) than graphite (1560 cm2). The Fe anode was found more stable than Al with greater charge transfer carried out in less time. Correlation of these results with those obtained during preliminary tests confirmed high removals (79 %) in 8 h. For the Al electrode, 24 h were required to achieve efficiency of 49 %. Keywords Electrocoagulation, electrode materials, acid whey, electroactive area, capacitance, Tafel slopes Introduction The electrodes are indispensable components of any electrochemical cell because just on their surface the processes of oxidation-reduction of the species occur together with other reactions carried out during electrolysis 1,2. When an electrocoagulation (EC) process is applied, the electrodes must be cost-effective and easy to handle. In addition, the electrodes used as sacrificial anodes must also possess great dissolution power. The most frequent materials used for EC processes of different effluents with good removal efficiencies are aluminum (Al) and iron (Fe), but other materials such as steel 3,4 have also been tested. http://www.jese-online.org/ mailto:jud_292003@yahoo.com.mx J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 ELECTROCOAGULATION OF WHEY ACIDS 90 In the present study, different materials acting as anodes (Al and Fe) and cathodes (graphite and Ti/RuO2) are tested for the EC and purification of residual acid whey. The evaluation is performed with respect to the electroactive electrode area and through polarization curves. Methodology Determination of electroactive area (EA) of electrodes Determination of real electroactive area (EA) was done for Al, Fe, graphite (G) and Ti/RuO2 electrodes. The cyclic scanning voltammetry technique, exploring the BASI Epsilon EC potentiostat 2.13 USB was used. Experiments were performed in 0.1 M KCl solution acidified with HCl to maintain pH 4.7, what simulates the initial pH of the acid whey 5,6. The electroactive area of each electrode surface was calculated by the capacitance of the double layer, Cdl, generated on the electrode in contact with an electrolyte 7. A glass beaker (2 L) containing 0.1 M KCl solutions was used as the electrochemical cell in which the electrodes were immersed (Fig. 1). The electrodes were submerged to a height of 5 cm, exposing a geometric area of approximately 100 cm2 to the solution. The dimensions of electrodes were as follows: Al (10.2  10  0.1 cm), Fe (10.1  10  0.2 cm), G (8.2  10  1.2 cm) and Ti/RuO2 mesh (10.5  10  0.1 cm). Titanium (Ti) mesh electrode (10  10  0.1 cm) and the saturated calomel electrode (SCE) served as the counter and reference electrode, respectively. Figure 1. Glass cell containing Ti mesh counter and SCE reference electrodes used for determination of electroactive area of working electrodes (Al, Fe, G, Ti/RuO2) Cyclic voltammetry experiments were performed at different scanning rates, V = 10100 mV s-1 in a potential window of ± 10 mV around the equilibrium potential (E0). Anodic (ia) and cathodic (ic) currents were obtained as electrochemical responses to the potential change. The capacitive current (icap) was calculated by means of equation (1), while Cdl value was calculated as the slope of linear relation obtained by presenting icap vs. V. The EA, is obtained by means of equation (2), where Cst is the normal capacitance taken as Cst = 60 F cm-2 for roughened electrodes 7. a c cap 2 i i i   (1) F. Prieto-García et al. J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 doi:10.5599/jese.381 91 dl st EA c c  (2) Measurements of polarization curves With the polarization curves it is possible to determine the electrode of the highest oxidation capacity attained with consumption of the lowest energy. The potentioamperometric technique was explored using a sample of acid whey (30 mL) and geometrically smaller electrodes. The electrodes were submerged to a height of 2.0 cm and the exposed geometric areas were 6.96 cm2 (Al), 8.78 cm2 (Fe), 4.65 cm2 (G) and 8.6 cm2 (Ti/RuO2). The real electrode areas were determined following the methodology described above. Three-electrode glass cell was used and shown in Figure 2a, where the working electrode is the G electrode, while Ti mesh and SCE served as the auxiliary and reference electrodes, respectively. Figure 2b shows a three-electrode cell containing 30 mL of acid whey used for chronoamperometric experiments, performed by applying different overpotentials, η, defined by the equation (3) for 45 minutes. Figure 2. Three-electrode glass cell used for determination of electroactive area of small electrodes (G, Ti-mesh and SCE are the working, counter and reference electrodes) a). Electrolytic cell containing 30 mL of acid whey for polarization measurements (Al, Ti-plate and SCE are the working, counter and reference electrodes) b) Constant stirring is maintained during the test to obtain the current (i) in response. The current density (j) is calculated by the equation (4). = Eapplied - E0 (3) j = i / EA (4) Results and discussion Determination of electroactive area (EA) of electrodes Cyclic voltammograms of Al, Fe, G and Ti/RuO2 electrodes in 0.1 M KCl recorded at different scan rates (v) are together with i vs. υ curves shown in Figures 36. Numerical data for icap determined by eq. (1) are collected in Table 1. Contrary to Figures 3 and 4 that showed ordinary capacitive current responses of G and Ti/RuO2 electrodes, in the case of Al and Fe electrodes presented in Figures 5 and 6, the tendency is quite different. Lack from usual linear icap vs. v response is particularly obvious for the Fe electrode and is probably due to the dissolution of electrode in acid medium. a) b) J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 ELECTROCOAGULATION OF WHEY ACIDS 92 E / V vs. SCE E / V vs. SCE Figure 3. Cyclic voltammograms of graphite electrode (G) in 0.1 M KCl, at different scanning rates (v = 0.01 to 0.10 V s-1) (A). icap vs. v (B) E / V vs. SCE v / V s-1 Figure 4. Cyclic voltammograms of Ti/RuO2 electrode in 0.1 M KCl at different scanning rates (v= 0.01 to 0.10 V s-1) (A). icap vs. v (B) E / V vs. SCE v / V s-1 Figure 5. Cyclic voltammograms of Al electrode in 0.1 M KCl at different scanning rates (v = 0.01 to 0.10 V s-1) (A). icap vs. v (B) The electroactive area (EA) of the working electrode represents the number of active sites where the electron transfer takes place and is usually estimated as the real electrode area (Areal) defined by eq. (2). EA can increase or decrease with respect to the geometric area, what is mainly due to the modification of the electro-active electrode surface. When an EC process is carried out, the anode (Al or Fe) undergoes oxidation reaction, which leads to the release of metal ions (sacrificial i / A i / A i / A i / A i / A i / A F. Prieto-García et al. J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 doi:10.5599/jese.381 93 anode) and concomitant dissolution process 4,8-11. causing diminishing of the surface area. At the other hand, increase of the EA could also happen due to the porosity induced by the EC process. E / V vs. SCE v / V s-1 Figure 6. Cyclic voltammograms of Fe electrode in 0.1 M KCl at different scanning rates (v = 0.01 to 0.10 V s-1) (A). icap vs. v B) Table 1. Capacitive currents (icap) for different EC electrodes at different scanning rates v V / V s-1 icap / A G Ti/RuO2 Al Fe 0.01 0.00209 0.00229 0.00003 0.0134 0.02 0.00318 0.00378 0.00005 0.0165 0.03 0.00434 0.00573 0.00007 0.0222 0.04 0.00538 0.00728 0.00009 0.0231 0.05 0.00623 0.00874 0.00011 0.0240 0.06 0.00718 0.01007 0.00013 0.0244 0.07 0.00799 0.01121 0.00015 0.0245 0.08 0.00899 0.01218 0.00017 0.0245 0.09 0.0098 0.01308 0.00019 0.0242 0.10 0.01055 0.01385 0.00021 0.0242 Double-layer capacitance (Cdl) and EA values, calculated using data in Table 1 and eq. (2), are summarized in Table 2. Table 2. Real area (EA) and capacitance (Cdl) of different electrodes for the electrocoagulation process Electrodes Equation R2 Cdl / F EA, cm2 GA*, cm2 Roughness factor G y=0.0936x+0.0014 0.9967 0.0936 1,560 103.84 15.03 Ti/RuO2 y=0.130x+0.0010 0.9821 0.130 2,167 107.05 20.24 Al y=0.002x +10-5 1.0000 0.0020 33.3 104.02 0.32 Fe y=0.101x +0.016 0.617 0.1010 1,689 105.02 16.1 GA* - Geometric area It is obvious from Table 2 that Ti/RuO2 electrode showed the largest EA (2,167 cm2), what is due to the RuO2 metal oxide that generates micro, meso and macropores, and so greater surface roughness and higher capacitance (Cdl) values were obtained. At the same time, Al electrode showed the smallest EA (33.3 cm2) because it is a smooth and polished metal plate that exhibits the lowest Cdl among all electrodes. It has generally been stated that for cathodes, greater EA is generally i / A i / A J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 ELECTROCOAGULATION OF WHEY ACIDS 94 beneficial. Data in Table 2 show that for Ti/RuO2 and G electrodes, EA are 2,167 cm2 and 1,560 cm2, respectively. This makes the Ti/RuO2 electrode to be better cathode under the perspective of electroactive areas. Also, regarding the electroactive area, the Fe electrode having EA of 1,689 cm2 seems better than the Al electrode having 33.3 cm2. Although being indicative, the value of EA, however, is not a definitive factor for the choice of the most proper electrodes for EC. Choice of better arrangement of electrodes by means of polarization curves Aluminum electrode Chronoamperometric, i vs. t responses of the Al electrode in acid way sample recorded during 45 min are presented in Figures 7 and 8. Similar behavior is observed at different potentials (Eapp) applied between 0.650 and 1,050 mV. As Eapp was increased, i was increased in the same way. However, at very high Eapp (850 and 1,050 mV) the decomposition of the medium is already occurring, which leads to unnecessary energy consumption. Figure 9 shows i vs. Eapp responses for the Al electrode (EA = 33.3 cm2) in the acid whey sample. It is obvious from Fig. 9 that the limiting current (il) where diffusional control begins is reached at about 400 mV vs. SCE and that diffusional currents are in a range of 0.039 and 0.042 A. Despite application of higher voltages, there are no greater transformations of the species present in the medium, up to the potential suitable for secondary reactions like the electrolysis of the water. Figure 10 shows the polarization curve, log j vs., of the Al electrode. In this graph, it is observed that the limiting current is reached by diffusional control at overpotential of 200 mV. This suggests that from the results obtained previously during the EC with a removal efficiency of 79 % in 8 h, the energy required can be reduced (by decreasing  from 1.74 to 0.2 V) to obtain the same removal efficiency and possible reduction of time. Time, s Figure 7. Chronoamperometric i vs. t responses of Al electrode in acid whey sample recorded during 45 minutes at Eapp between 650 mV and +1,050 mV 1 TIME, s i / A F. Prieto-García et al. J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 doi:10.5599/jese.381 95 Time, s Figure 8. Chronoamperometric i vs. t responses of Al electrode recorded at Eapp between 650 mV and 550 mV (zoom of Fig. 7) E / mV Figure 9. i vs. Eapp of Al electrode in acid whey sample at Eapp between 650 mV and +650 mV Figure 10. log j vs. dependence of Al electrode in acid whey sample 1 TIME, s 1 2 -7 -6 -5 -4 -3 -2 -1 0 0 300 600 900 1200 1500 1800  / mV lo g ( j/ m A c m -2 ) i / A i / A J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 ELECTROCOAGULATION OF WHEY ACIDS 96 Iron electrode The chronoamperometric, i vs. t curves of the Fe electrode in acid whey sample recorded during 45 min are shown in Figures 11 and 12. Almost constant current values observed with time at each Eapp applied between 650 and 150 mV suggest that only capacitive currents are generated at the Fe electrode in contact with the acid whey solution. When applying Eapp between 0 to 100 mV, however, the first change in the oxidation state of Fe° to Fe2+ is observed with transfer of 2e coupled with the decomposition of the medium. At Eapp between 100 to 450 mV, a second change in current is observed due to the electrochemical oxidation of Fe2+ to Fe3+, so that the oxidation of iron is considered to occur in two stages (eqs. 5 and 6): Fe°  Fe2+ + 2e (5) Fe2+  Fe3+ + 1e (6) Finally, by applying Eapp higher than 450 mV the electrolysis of the medium that is decomposition of the whey begins, what is accompanied by the significant current increase with time. i vs. Eapp and log j vs.  dependences are presented in Figures 13 and 14. Here also, two different processes which are related to iron oxidation can be observed as in the chronoamperometry experiments. With these polarization curves it is verified that in the EC system, generation of Fe2+ or Fe3+ can be favored to improve the efficiency of the system in a shorter time and lower energy cost. Time, s Figure 11. Chronoamperometric i vs. t responses of Fe electrode in acid whey sample recorded during 45 minutes at Eapp between 1050 mV and +1050 mV The above statement can be based on the Pourbaix diagram for the thermodynamic states of the iron in aqueous solution, where when applying potentials within the range of 0.6 to 1.6 V vs. SCE, the oxidation process occurs and Fe2+ or Fe3+ ions are released depending on the pH of the solution. For acid conditions, both species are present and the process of corrosion is facilitated. It should be analyzed in more detail, however, which reaction would favor the EC process for the whey solution 1 I, A i / A F. Prieto-García et al. J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 doi:10.5599/jese.381 97 and formation of the iron oxy-hydroxides. Thus, one would be able to establish the optimum limiting current according to the limiting reagent that controls the reaction. Time, s Figure 12. Chronoamperometric i vs. t responses of Fe electrode at Eapp between 650 mV and 450 mV (zoom of Fig. 11) E / mV vs. SCE Figure 13. i vs. Eapp of Fe electrode in acid whey sample at Eapp between 650 mV and 850 mV The bibliographical reports on the EC processes using iron electrodes are contradictory. Most EC studies have focused on the removal of contaminants by their co-precipitation with the solid(s) such are already formed precipitates of Fe(OH)2(s) and Fe(OH)3(s). Also, the reactions reported in the literature showed a certain ambiguity in the proposed mechanisms. Some studies 13-15 have reported that the oxidation of iron Fe0 to Fe2+ occurs in an electrolytic form and produces insoluble Fe(OH)2(s) compounds by hydrolysis. Other authors 16 pointed to the formation of Fe(OH)2(s) without giving details of how it occurs. Several studies 8,17,18 reported formation of Fe2+ at the anode that is followed by oxidation to Fe3+ due to dissolved oxygen (DO) and rapid formation of Fe(OH)3(s). The third mechanism reported 7,8,10 involves the single and fast electrolytic oxidation 1 I, A 1 E/mV vs. SCE i / A i / A J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 ELECTROCOAGULATION OF WHEY ACIDS 98 step of Fe0 to Fe3+, followed by hydrolysis to produce Fe(OH)3(s). Finally, some studies 16,19,20 have reported formation of Fe(OH)3(s) as the final product during EC without specifying the reactions involved. According to 21, the third mechanism is questionable. These authors pointed out dependence of the kinetics of these reactions on the pH of the medium. They reported that at pH 7.5, approximately 80% of the Fe2+ initially formed is oxidized to Fe3+ in less than 10 minutes, while at pH 6.5, the same oxidation process takes about 300 minutes (5 h). The rapid increase in Fe2+ oxidation rate with pH increase is consistent with other reports in the literature, where based on equations (7) and (8), it was shown that increase of pH increases the oxidation rate of Fe2+ for about 100 times 2224.  / mV Figure 14. Log j vs. dependence of Fe electrode in acid whey sample. 4Fe2+ + O2 + 2H2O + 8OH ↔ 4Fe(OH)3(s) (7) d[Fe2+]/dt = k[Fe2+] PO2 [OH -]2 (8) In eq. (8), k is the rate constant, PO2 is the oxygen partial pressure, while the molar concentrations of present species are represented in the brackets. A slight increase in the concentration of OH ions as observed during EC and corroborated with the increase of pH, has resulted in a greater concentration of the Fe2+ species forming Fe3+ by subsequent oxidation and Fe(OH)3(s) by precipitation. Since OH ions are consumed during the hydrolysis of Fe3+, pH in the electrolytic cell decreases in a subsequent step that does not occur immediately. By the time elapsed between the production of Fe2+ and its oxidation to Fe3+ by the oxygen dissolved in the medium, a reaction that is much slower has been indicated. Graphite electrode In Figures 15 and 16, the chronoamperometric i vs. t responses of the G electrode recorded through 45 min are presented, showing the same behavior at different Eapp applied. As Eapp increases, i increased in the same way. At very negative Eapp (1050 mV), however, it can be observed that the decomposition of the medium occurs. By presenting log j vs. dependence, Fig. 17 suggests that the limiting current (il) is occurring at overpotential of 500 mV, where diffusional control begins. 1 2 3 4 5 6 7 8 9 10 lo g ( j / m A c m -2 ) F. Prieto-García et al. J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 doi:10.5599/jese.381 99 Time, s Figure 15. Chronoamperometric i vs. t responses of G electrode in acid whey sample recorded during 45 min at Eapp between 70 mV and 1050 mV. Time, s Figure 16. Chronoamperometric i vs. t responses of the G electrode at Eapp between 12 mV and 250 mV (zoom of Fig. 15)  / mV Figure 17. log j vs.  dependence of G electrode in acid whey sample. i / A i / A lo g ( j /m A c m -2 ) J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 ELECTROCOAGULATION OF WHEY ACIDS 100 Selection of the anodic material for the electrocoagulation process. With the electrochemical information obtained so far, the Tafel slopes for the electrodes acting as sacrificial anodes (Al and Fe) are compared in Figure 18. To select the best electrode, the largest slope must be taken into account. The results for Fe and Al electrodes are different, for the Al electrode, b = -54.55 mV dec-1 and for Fe, b = -109.98 mV dec-1. In this respect, it is possible to define that the Fe electrode is considered the most effective. Figure 19 shows a better separation of the precipitate and purified liquid more transparent with the use of the Fe electrode (Figure 19 a). log (j / A cm-2) Figure 18. Tafel slopes of Fe and Al electrodes in acid whey samples Figure 19. Purification kinetics of acid whey with Fe (a) and Al (b) electrodes Conclusions The iron electrode proved to be better anode than Al for the EC process. This is due to its stable thermodynamic behavior in the range of applied overpotentials, which translates into a greater transfer of charge in a shorter time. By correlating these results with the results obtained during the preliminary tests, it can be confirmed that the Fe electrode is better than the Al electrode. With the Fe electrode, greater removals (79 are obtained in less time (8 h)). On the other hand, with the Al 1 2 3 log (i/A cm -2 )  /m V v s- S C E a) b)  / m V v s. S C E F. Prieto-García et al. J. Electrochem. Sci. Eng. 7(2) (2017) 89-101 doi:10.5599/jese.381 101 electrode, the results of macroelectrolysis required more time (24 h) to achieve an efficiency of 49 %. Based on the determinations of the electroactive area, the Ti/RuO2 electrode (2,167 cm2) proved to be a better cathode than the graphite (1,560 cm2). References [1] M. Piña, A. Martín, C. A. González, F. Prieto, A. Guevara, J. E. García. Revista Mexicana de Ingeniería Química 10(2) (2011) 257-271. [2] A. P. Restrepo, A. Arango, L. F. Garcés. Producción + Limpia 1(2) (2006) 58-77. [3] E. Ojeda, R. Hing, Y- González. Revista CENIC Ciencias Químicas 43(1) (2912), 21-42. [4] S. Tchamango, E. Nanseu-Njiki, D. Ngameni, A. Hadjiev, A Darchen. Science of the Total Environment 408 (2010) 947–952. [5] P. Panesar, J. Kennedy, D. Gandhi, K. Bunko, Food Chemistry 105 (2007) 1-14. [6] A. Abaigar, ITG Ganadero 94(8) (2009) 13-17. [7] N, Balasubramanian, K. Madhavan, Chemical Engineering Technology 24 (2001) 519–521. [8] M. Y. Mollah, P. G. Morkovsky, A. G. Gomes, M. Kesmez, J. Parga, Journal of Hazardous Materials 114(1-3) (2004) 199–210. [9] O. T. Can, M. Bayramoglu, M. Kobya. Industrial Engineering Chemistry Research 42 (2003) 3391–6. [10] M. Kobya, O. T. Can, M. Bayramoglu. Journal of Hazardous Materials B1001 (2003) 63–78. [11] H. Inan, A. Dimoglo, H. Simsek, M. Karpuzku. Separation and Purification Technology 36 (2004) 23–31. [12] G. Chen, Separation and Purification Technology 38(1) (2004) 11–41. [13] V. P. Osipenko, P. I. Pogorelyi. Metallurgist 21(9-10) (1977) 44–45. [14] M. Y. Mollah, R. Schennach, J. R. Parga, D. L. Cocke. Journal of Hazardous Materials 84(1) (2001) 29–41. [15] R. Parga, D. L. Cocke, V. Valverde. Cheical Engineering Technology 28(5) (2005) 605–612. [16] D. Ghernaouta, A. Badisa, A. Kellila, A. Desalination 219(1-3) (2008) 118–125. [17] X. M. Chen, G. Chen, P. L. Yue. Separation and Purification Technology 19(1) (2000) 65–76. [18] H. K. Hansen, P. Núñez, R. Grandon. Minerals Engineering 19(5) (2006) 521–524. [19] D- Mills, Journal American Water Works Association 92(6) (2000) 34–43. [20] P. R. Kumar, S. Chaudhari, K. Khilar, S. P. Mahajan. Chemosphere 55(9) (2004) 1245–1252. [21] D. Lakshmanan, D. Clifford, and S. Gautam. Environmental Science Technology 43 (2009) 3853–3859. [22] P. C. Singer, W. Stumm. Journal American Water Works Association 62 (1970) 198–202. [23] W. Stumm, S. Morgan, Journal. Aquatic Chemistry; 1981. Wiley-Interscience, New York. [24] M. Bond, S. Kratsis and S. Mitchell. Journal Analyst 122 (1997) 1147-1152. © 2017 by the authors; licensee IAPC, Zagreb, Croatia. This article is an open-access article distributed under the terms and conditions of the Creative Commons Attribution license (http://creativecommons.org/licenses/by/4.0/) http://creativecommons.org/licenses/by/4.0/)