Transactions Template JOURNAL OF ENGINEERING RESEARCH AND TECHNOLOGY, VOLUME 1, ISSUE 4, DECEMBER 2014 156 Bidirectional WDM Access Architecture Employing Cascaded AWGs and RSOAs. Fady I. El-Nahal Department of Electrical Engineering, The Islamic University of Gaza, Gaza, P.O.Box 108, Palestine, email: fnahal@iugaza.edu.ps. Abstract—Here we propose a bidirectional wavelength division multiplexing (WDM) access architecture employing cascaded cyclic arrayed waveguide gratings (AWGs) and reflective semiconductor optical amplifiers (RSOAs) for system applications mainly in wavelength routed fiber-to-the-home (FTTH) networks. These architectures can address multiple N2 customers using N wavelengths by employing multiple NxN AWGs at the central office (CO) and multiple 1×N AWGs at the distribution points (DPs). A 20 km range colorless WDM passive optical network (WDM-PON) was demonstrated for both 4 Gbit/s downstream and 2.5 Gbit/s upstream signals respectively. The BER performance of our scheme demonstrates that our scheme is a practical solution to meet the data rate and cost-efficient of the optical links simultaneously in future access networks. Index Terms—Wavelength-division-multiplexing passive optical networks (WDM/PONs), Fiber to the home (FTTH). Arrayed waveguide gratings (AWGs), Reflective semiconductor optical amplifiers (RSOAs). I INTRODUCTION The rapid growth in Internet traffic and bandwidth inten- sive applications is continuing to fuel the penetration of fiber networks into the access network segment [1]. Wavelength- division-multiplexing passive optical networks (WDM/PONs) are an attractive option due to their high ca- pacity, easy management, network security, protocol trans- parency, and easy upgradability [2]. PON systems in fiber to-the-home (FTTH) networks have been widely deployed to fully support “triple-play” services including data, voice, and video services. Among various PON technologies, WDM/PONs, which offer point-to-point connectivity via a dedicated wavelength to each customer, are believed to eventually provide an optimal FTTH architecture [3]. The rapid deployment of WDM into the core and metro- politan networks has cut down WDM components costs, and pushed WDM technology closer to the end-user. The AWG is a key WDM technology, offering high wavelength selec- tivity, low insertion loss, small size, high channel count and potentially low cost [4-6]. Several WDM/PON systems have been studied recently where a reflective semiconductor opti- cal amplifier (RSOA) plays an important role [7–15]. The RSOA replaces the high cost WDM source at the ONU and can be used as a modulator and amplifier [16-18]. This gives additional gain enabling the possibility of avoiding the use of an Erbium Doped Fiber Amplifier (EDFA) in the system. In these systems, both the upstream and downstream chan- nels use the same wavelength for improving the wavelength utilization efficiency. Cascaded Arrayed-Waveguide Gratings (AWGs) access architectures are discussed here [19-24]. These architectures can route to a large number of customers using a minimal set of wavelengths by employing AWGs [25], while offering scalability and improved crosstalk. In this work a cascaded AWG-based access architecture that consists of multiple N×N AWG’s at the CO and multiple 1×N AWG’s at the dis- tribution points (DP) is investigated. N wavelengths are mul- tiplexed and transmitted from the CO, offering unique opti- cal path for each end user for both downstream and up- stream transmission. Each AWG at the DP addresses N end users where the end users transmit in the same wavelength that they receive. A commercially available simulation tool was used for the calculations reported in this work [26]. II PROPOSED ARCHITECTURE Space wavelength switching can be attained by utilizing the periodic spectral response of the AWG, and its Latin routing capability [4]. This is achieved by setting the AWG Free spectral range (FSR) to match the product of the number of output ports and the channel spacing. In addition, the num- ber of wavelengths must equal the number of output ports. Consequently, for a symmetric NN AWG, the output port from which wavelengths appear will depend on the input port at which the wavelengths were launched. The minimum number of wavelength channels needed for N2 connections is N. An example of the wavelength assignment is shown in Table 1, where the same wavelengths are used for different connections. For example, 4 is used for N connections such as 4 to 1 and 3 to 2 [4]. F. I. El-Nahal / Bidirectional WDM Access Architecture Employing Cascaded AWGs and RSOAs. ( 2014) 157 TABLE 1 An example of the wavelength assignment in an N×N AWG router. The same functionality can be achieved by employing active AWG, an AWG with an array of phase modulators on its arrayed-waveguides section, where a programmable linear phase-profile or a phase hologram is applied across the ar- rayed-waveguide section. Following the second free propa- gation region, this results in a wavelength shift at the output section of the AWG. This effect can be used to tune the de- vice, and also allows space-wavelength switching function- ality [27,28]. Thus, just one input port of the NN AWG can be used for downstream transmission, whilst the remaining ports are used for upstream reception. Since active AWG’s cost is relatively higher than passive AWGs, A passive N×N AWG, circulators, and an opto-mechanical switch are used to achieve the desired wavelength routing in this work [19]. Fig. 1 shows the proposed access architecture. Packets are modulated onto one of R wavelengths from a fast tunable laser depending on the destination Optical Network Unit (ONU) [22]. The cells reach the first stage S1, which con- sists of a P-way passive optical splitter. The cells are routed into the appropriate arm and progress to the second stage S2, consisting of a Q-way power splitter, where each of the arms of the splitter are connected with one of the upstream ports, respectively, of the Pth N×N AWG. Space-wavelength switching is achieved by using an AWG in conjunction with a power splitter and an opto-mechanical switch. For the pro- posed WDM access architecture shown in Fig. 1, there would be R = 24 wavelengths spaced by 100GHz (0.8nm), requiring a Q = 24 port AWG. The AWGs at the second and third stages (S2 and S3) are matched to have the same FSR (2400 GHz), passband width and number of input/output ports, so that Q = R. The packets are routed out of the CO and onto stage S3, located at the distribution points (DPs), consisting of AWGs with R = 24 ports. Each AWG acts as a fixed optical wavelength router directing the wavelength multiplexed cells to the destination ONU located in the cus- tomer premises. At the ONU, using optical splitter/coupler, portion of the signal is fed to a receiver. For up-link, the other portion of the downstream signal from the split- ter/coupler is re-modulated using 2.5 Gb/s NRZ upstream data by RSOA in the ONU. The re-modulated On-off keying (OOK) signals are sent back over the fiber to the CO where they are de-multiplexed by the AWG. The reflected optical signal is detected by a PIN-photodiode. Uplink optical side- bands produce crosstalk when uplink data was detected at the CO. Crosstalk can be reduced by using Bessel filter. The total number of ONUs served is the product PQR. For P = 12, Q = R = 24 this access network can provide service to 6192 customers, thus allowing a graceful evolution from current passive optical networks (PON) infrastructures [29]. A factor P downstream bandwidth capacity can be achieved by replacing stage 1 consisting of a P -way splitter by a bank of P tunable lasers and modulators, so that the network con- sists of P = 12 sub-networks, where each can serve 576 ONUs [22]. III SIMULATION ISSUES AND RESULTS The laser source is externally modulated by a Mach-Zehnder modulator. The data stream, which modulates the continuous wave laser source, was generated using an NRZ shaped pulse train. The average output power of the source is 20dBm while the linewidth of the laser is 10MHz. A Gauss- ian approximation of the modal field in the waveguides was used in the AWG model and the insertion loss is assumed to be 4dB, which is a typical value in standard AWGs. Polari- zation dependent loss has been ignored. The waveguide is assumed to be symmetrical and only the fundamental mode was taken into account. These assumptions can be justified as they have minimal effect on the simulation results. A polarization independent RSOAs that can handle signals with arbitrary polarization state were used. Limitations of the RSOA model used here include neglecting the gain dis- persion. Neglecting the gain dispersion is acceptable as long as the bandwidth of the optical signal is significantly smaller than the amplification bandwidth, which is typically of the order of several tenth of nms. A 20 km of standard single- mode fibre (SMF) with 0.2 dB/km loss was used for fibre transmission simulations. This module solves the nonlinear Schrödinger equation describing the propagation of linearly- polarized optical waves in fibers using the split-step Fourier method. This model allows simulating nonlinear (SPM, FWM, XPM) and Raman effects in WDM systems. BER simulations were carried out with a Bit Rate of 4 Gb/s downstream and 2.5 Gb/s upstream for a 1.7 GHz bandwidth receiver respectively. The received eye diagrams of down- stream and upstream signals were measured at ONU and CO respectively. The received eye diagrams of arbitrary down- stream and upstream signals are shown in Fig. 2 and Fig. 3 respectively. The eye-diagrams are widely open and prove that the system is stable and that crosstalk is negligible. F. I. El-Nahal / Bidirectional WDM Access Architecture Employing Cascaded AWGs and RSOAs. ( 2014) 158 Figure 1 Cascaded AWGs based access architecture The BER versus input optical power Pin curves for the downlink and uplink are shown in Fig. 4. It is clear from the results that both downlink and uplink do provide good BER performances. It is noted from the figure that the BER for the downlink and uplink goes down with increasing Pin from 10 dBm to 20 dBm. For the downlink, when Pin = 10 dBm, the BER = 1.3×10-9 and quality factor Q= 5.9. When Pin = 20 dBm, the BER = 3.2×10-32 and Q = 11.8. For the uplink, the BER goes down slowly with increasing Pin from 10 dBm to less than 15 dBm. When Pin = 10 dBm, the BER = 2.3× 10-9 and Q = 5.9. For Pin ≥ 15 dBm, the BER is nearly con- stant. When Pin =20 dBm, the BER = 1.4×10 -39 and Q = 13.1. This can be explained by the fact that the RSOA is operating in the gain saturation region. Figure 2 Eye diagram of downlink The variation of the gain of RSOA with the optical input power Pin is shown in Fig. 5. It is clear that the maximum gain appears at Pin = 10 dBm, then goes down to reach the lowest gain at Pin= 20 dBm. Figure 3 Eye diagram of uplink V CONCLUSION This paper has presented novel simulation results to eval- uate AWGs and RSOAs for system applications mainly in new bidirectional access architectures employing cascaded arrayed-waveguide grating technology. Space wavelength F. I. El-Nahal / Bidirectional WDM Access Architecture Employing Cascaded AWGs and RSOAs. ( 2014) 159 switching was achieved in these networks using a passive AWG in conjunction with an optical mechanical switch. These architectures can address up to 6912 customers em- ploying only 24 wavelengths, separated by 0.8 nm. RSOA is used as low cost colorless transmitters for high-speed optical access exploiting WDM technology. The results obtained demonstrate that cascaded AWGs access architectures have a great potential in future FTTH networks. Figure 4 BER versus input power Figure 5 The variation of RSOA gain with input power REFERENCES [1] Elaine Wong, “Next-Generation Broadband Access Networks and Technologies”, J. Lightwave Technol., vol. 30, no. 4, pp. 597-608, 2012. [2] F.T. An, D. Gutierrez, K.S. Kim, J.W. Lee, L.G. Kazov- sky, “SUCCESS-HPON: a next generation optical ac- cess architecture for smooth migration from TDM–PON to WDM–PON”, IEEE Commun. Mag. vol. 43, no. 11, pp 540-547, 2005. [3] S.-J. Park, C.-H. Lee, K.-T. Jeong, H.-J. Park, J.-G. Ahn, K.-H. Song, “Fiber-to the- home services based on wavelength-division-multiplexing passive optical net- work”, J. Lightwave Technol. Vol. 22, pp. 2582–2591, 2004. [4] M.K. Smit, C. vanDam, “PHASAR-based WDM- devices: Principles, design and applications”, IEEE J. Select. Top. Quant. 2 (2) (1996) 236–250. [5] M.K. Smit, “New focusing and dispersive planar com- ponent based on an optical phased array”, Electron. Lett. 7 (24) (1988) 385–386. [6] G.R. Hill, “A wavelength routing approach to optical communication networks”, Brit. Telecom. Technol. J. 3 (6) (1988) 24–31. [7] S. Y. Kim, S. B. Jun, Y. Takushima, E. S. Son and Y. C. Chung, “Enhanced performance of RSOA-based WDM- PON by using Manchester coding,” J. Optical Network- ing, vol. 6, pp. 624-630, 2007. [8] Y. C. Chung, “Recent Advancement in WDM PON Technology”, Tech. Dig. ECOC 2011, Geneva, Paper Th.11.C.4. [9] J. Prat, C. Arellano, V. Polo, C. Bock, “Optical network unit based on a bidirectional reflective semiconductor optical amplifier for fiber-to-the home networks”, IEEE Photon. Technol. Lett., vol. 17, no. 1, pp. 250-252, 2005. [10] M.D. Feuer, J.M. Wiesenfeld, J.S. Perino, C.A. Burrus, G. Raybon, S.C. Shunk, N.K. Dutta, “Single-port laser- amplifier modulators for local access”, IEEE Photon. Technol. Lett. vol. 8, no. 9, pp. 1175–1177, 1996. [11] N. Buldawoo, S. Mottet, F. Le Gall, D. Sigonge, D. Meichenin, S. Chelles, “A semiconductor laser amplifi- er-reflector for the future FTTH applications”, in: Proc. Eur. Conf. Opt. Commun. (ECOC 1997), Edinburgh, UK, 1997, pp. 196–199. [12] J.M. Kang, S.K. Han, “A novel hybrid WDM/SCM- PON sharing wavelength for upand down-link using re- flective semiconductor optical amplifier”, IEEE Photon. Technol. Lett. vol.18, no. 3, pp. 502-504, 2006. [13] G.C. Kassar, N. Calabretta, I.T. Monroy, “Simultaneous optical carrier and radio frequency re-modulation in ra- dio-over-fiber systems employing reflective SOA modulators”, in: Lasers and Electro-Optics Society (LEOS 2007), October, 2007, pp. 798–799. [14] A. Kaszubowska, L. Hu, L.P. Barry, “Remote down- conversion with wavelength reuse for the radio/fiber up- link connection”, IEEE Photon. Technol. Lett. vol. 18, no. 4, pp.562–564, 2006. [15] T. Kuri, K. Kitayama, Y. Takahashi, “A single light- source configuration for full-duplex 60-GHz-band ra- dio-on-fiber system”, IEEE Trans. Microw. Theory Tech. vo. 51, no. 2, pp. 431–439, 2003. [16] T. Kim, K. Jeung-Mo, and H. Sang-Kook, "perfor- mance analysis of bidirectional hybrid WDM/SCM PON link based on reflective semiconductor optical amplifier" Microwave and optical technology letters, F. I. El-Nahal / Bidirectional WDM Access Architecture Employing Cascaded AWGs and RSOAs. ( 2014) 160 ISSN 0895-2477, Vol. 48, April, 2006. [17] Zhansheng Liu et al., "Experimental Validation of a Reflective Semiconductor Optical Amplifier Model Used as a Modulator in Radio Over Fiber Systems", IEEE Photon. Technol. Lett., vol. 23, no. 9, pp. 576– 578, 2011. [18] M.C.R. Medeiros, R. Avó, P. Laurêncio, N.S. Correia, A. Barradas, H.J.A. da Silva, I. Darwazeh, J.E. Mitch- ell, P.M.N. Monteiro, “Radio over fiber access network architecture employing reflective semiconductor optical amplifiers”, in: Proc. ICTON-MW’07, Sousse, Tunisia, 2007, pp. 1–5. [19] I. Tsalamanis, M. Toycan, S.D. Walker, “Study of hy- brid cascaded AWG-based access network topology”, in: Proc. ICTON, Nottingham, UK, 2006. [20] F. El-Nahal, R.J. Mears, “Multistage WDM access ar- chitecture employing cascaded AWGs”, Optical Fiber Technology, vol. 15, no. 2, pp. 181–186, 2009. [21] M.C. Parker, F. Farjady, S.D. Walker, “Space/wavelength-routed ATM access architecture based on cascaded programmable arrayed-waveguide gratings”, in: Proc. CLEO’98, San Francisco, CA, 1998. [22] F. Farjady, M.C. Parker, S.D. Walker, “An evolutionary access network upgrade path based on a multi- dimensional-time-space-wavelength architecture”, in: Proc. NOC’98, Manchester, UK, 1998. [23] F. Farjady, M.C. Parker, S.D. Walker, “Evolutionary multidimensional access architecture featuring cost- reduced components”, in: Proc. ICAPT’98, Ottawa, ON, Canada, 1998. [24] M.C. Parker, F. Farjady, S.D. Walker, “Wavelength- tolerant optical access architectures featuring N- dimensional addressing and cascade arrayed waveguide gratings”, J. Lightwave Technol. 16 (12) (1998) 2296– 2302. [25] M.C. Parker, F. Farjady, S.D. Walker, “Application of synthetic aperture techniques to AWG passband con- trol”, in: Proc. IPR’98, Victoria, BC, Canada, 1998. [26] Optisystem from optiwave. [27] M.C. Parker, S.D. Walker, A. Yiptong, R.J. Mears, “Ap- plication of active arrayedwaveguide gratings in dynam- ic WDM networking and routing”, J. Lightwave Tech- nol. 18 (12) (2000) 1749–1756. [28] F. I. El-Nahal, R.J. Mears, “Applications of active AWGS in future WDM networks”, Opt. Eng. 42 (3) (2003) 867–874. [29] D. Hopper, Fujitsu Telecommunications Europe, Ltd., private communication.