Journal of Mechanical Engineering Science and Technology ISSN: 2580-0817 Vol. 1, No 1, July 2017, pp. 9-14 9 DOI: 10.17977/um016v1i12017p009 Factors Affecting the Surface Roughness in Sinking EDM Process Ahmad Atif Fikri1, a *, Maftuchin Romlie1, Aminnudin1 1Department of Mechanical Engineering, Faculty of Engineering, Universitas Negeri Malang, Semarang Street No. 5, Malang, East Java, Indonesia Corresponding author : * atif.fikri.ft@um.ac.id ABSTRACT The purpose of this study is to gain insights into the surface quality (smoothness) of sinking EDM machining products. Among other non-conventional machining processes, Electrical Discharge Machining (EDM) is the most commonly used process. EDM is a machining process that uses electric sparks created between a workpiece and a tool (electrode). As a manufacturing process, EDM is used for workpieces which have intricate contours and precise dimensions, and works by using electric discharges (sparks) applied in a rapid series of repetitive electrical discharges between the two electrodes, separated by a dielectric fluid, and subject to an electric voltage. Since the tool tends to wear easily and the mould material is very hard and tough, it is necessary to keep within appropriate EDM machining parameters, so that the smoothness of the mould lives up to expectations. Therefore, the parameters of sinking EDM process should be well established to produce the expected results, i.e. the smoothest surface quality and the maximum removal rate. Regarding the electrode materials used, conducting a further experiment is required to achieve the appropriate settings of pulse current, on-time, off-time, servo voltage, and gap width. This experimental study involved several factors: (a) electrode material, (b) magnitude of current, (c) on-time, and (d) quality of surface (smoothness). In this study, the gap between the electrode and the workpiece was controlled at a distance of 40 μm, and with an off-time of 5 seconds, the same dielectric fluid, the same flow speed and the same dielectric immersion, and using the workpiece (AISI P20M steel). Quantitative approaches (t test, one-way, and ANOVA) were applied to analyse the results of comparison test and to determine the best parameter in sinking EDM process. Copyright © 2017Journal of Mechanical Engineering Science and Technology All rights reserved Keywords: EDM process, Electrode, Surface Roughness I. Introduction The development of manufacturing technology is growing rapidly along with the need to improve human welfare. Means of transportation such as motorcycles, home appliances, and communications devices such as cellular telephone, both made of metal or other materials (plastic and composite), are advancing. The development speed has been greatly influenced by the availability of supported technology, such as machining, formation, and moulding technology. The oldest machining process is the one performed by removing material in the form of chips. In metallic materials machining, the most used tools are lathes, freis, saws, grinders, etc, whereas in non-metal machining, the process is done by casting, forming, and moulding. Therefore, in mass manufacturing industry (casting, forming and moulding), the process of producing moulds, particularly the ones made of metal (both ferrous and non-ferrous), should be faster and efficient. - The durability of mould is strongly influenced by the mechanical properties of metal as the moulding material. Materials that have a high resistance to a wide range of requirements are typically made of hard materials but with low machining capabilities. In other words, the production capability of the machine is very low, because it is beyond the machine’s capacity to work with much stronger cutting tools. Furthermore, workpieces with difficult and intricate contours are no longer able to be processed with any conventional machine, or even with the most advanced CNC milling machine. Non-conventional machines such as chemical machining, electrochemical machining, electrical discharge machining, and high energy beam machining, are intended to manufacture products with intricate and complex contours. One of the four types of non-conventional machines owned by the Department of Mechanical Engineering, Universitas Negeri Malang, is the electrical discharge machining (EDM), namely sinking EDM. According to Schey (2009) [1], the surface quality of mailto:atif.fikri.ft@um.ac.id 10 Journal of Mechanical Engineering Science and Technology ISSN: 2580-0817 Vol. 1, No. 1, July 2017, pp. 9-14 Ahmad Atif Fikri et.al (Factors Affecting the Surface Roughness in Sinking EDM Process) EDM products is determined by many factors; the surface becomes rougher if the current density is higher, the viscosity of the dielectric material is higher, and the frequency is lower. These parameters highly depend on the enabled settings in the machine's features. There are various metals with different mechanical properties which can be used as a workpiece for intended purposes. EDM is capable of handling the mechanical properties of metals, in terms of hardness, tensile strength, and toughness under static and dynamic loads. EDM process is used in mould-making, thus surface smoothness is prioritised. In conventional machining process, the roughness level is determined by the established parameters in the machine’s system and the type of cutting tool used, thus the desired degree of smoothness is more achievable. While in EDM process, the factors affecting results are very complex, because the metal etching process involves heat generated by electric sparks, frequency of current discharge (on-current), level of cathode electrical conductivity (cutting tool), dielectric material, and mechanical properties of the workpiece (melting point). Dewangan (2010) [2], through his study on the steel AISI P20, concluded that the forming tool (cathode) wear was affected by the amount and frequency of current discharge, and the diameter of the forming tool. The fact that forming tool wear occurred showed how the factors affecting the surface smoothness of the mould were becoming more complex. The forming tool materials that can be used in EDM are copper, brass, and graphite. These materials are more easily formed using a machine with a simple cutting tool (HSS material), thus the desired shape or dimension can be very easily achieved. A research conducted by Kumar et al. (2012) [3] found that silver electrode provided a better performance in certain characteristics, but was relatively costly. Thus, graphite electrode was preferable in terms of metal removal rate (MRR) since its cost was comparatively lower than copper. The EDM machining parameters examined were fixed distance control variable between the electrode and the workpiece, positive polarisation (electrode connected to the positive pole), and the use of dielectric available in the market. The research only focused on volume8 reduction speed, not on surface quality (smoothness). A mould is (usually) made of hard solid steel which has an intricate contour and thus very difficult to process with a conventional machine. Consequently, the use of non-conventional machines, one of which is EDM, is more suitable for mould-making. The value of material removal rate and level of surface roughness of sinking EDM products depend on several parameters, such as pulse current, on- and off-time, servo voltage, and gap width. The bigger the value of pulse and gap width and the smaller the value of off-time and servo voltage, the higher the material removal will rate. If the value of pulse and width gap is big, and the value of off-time and servo voltage is too small, then the surface of the products will be rough [4]. The fact that cutting tool wear occurs and mould material is very hard and tough, denotes that it is necessary to utilise appropriate EDM machining parameters so that the surface quality of mould lives up to expectations [5]. Therefore, the parameters of sinking EDM process should be well established to produce the expected results, i.e. the smoothest surface quality and the maximum removal rate. Regarding the electrode materials used, conducting a further experiment is required to achieve the appropriate settings of the pulse current, on-time, off-time, servo voltage, and gap width. A. Determining Factors in the Ease of EDM Process The machining factors affecting the EDM machines differ from the conventional ones. Conventional machines rely on the hardness of tools and workpieces, whereas EDM machines depend on λ (thermal conductivity) θ (melting point) and ρ (electrical resistivity) [6]. The machining time cannot be considered as a parameter for the ease of EDM process because there are many other relatively complex factors affecting it, such as adhesion, cavitation, and short-circuiting [6]. II. Method This experimental study was done to investigate the quality of surface roughness of sinking EDM machining products. The variables involved in this study were (a) magnitude of current, (b) forming tool materials, (c) length of the current release time and (d) level of roughness. A. Tool, Workpiece, And Data Analysis Technique Electrode materials used were: (a) copper, (b) brass, and (c) graphite. The workpiece materials used were the ones for manufacturing plastic moulds, namely Assab Steel 618 SUPREME, AISI ISSN: 2580-0817 Journal of Mechanical Engineering Science and Technology 11 Vol. 1, No. 1, July 2017, pp. 9-14 Ahmad Atif Fikri et.al (Factors Affecting the Surface Roughness in Sinking EDM Process) P20M Steel (chemical composition: C 12:37%, Cr 2:00%, Mo 12:20%, Mn 1.4%, Si 0.3%, Ni 1.0%, and S