Jtam-A4.dvi JOURNAL OF THEORETICAL AND APPLIED MECHANICS 54, 1, pp. 41-52, Warsaw 2016 DOI: 10.15632/jtam-pl.54.1.41 ANALYTICAL AND EXPERIMENTAL VIBRATION ANALYSIS OF TELESCOPIC PLATFORMS Adil Yucel, Alaeddin Arpaci Istanbul Technical University, Department of Mechanical Engineering, Taksin, Istanbul, Turkey e-mail: adil.yucel@itu.edu.tr; arpacial@itu.edu.tr In this study, vibration analysis of a telescopic platform is conducted, and the platform structure is reconstructed to satisfy vibrational standards. The analysis is realised using so- lidmodelling, finite elements and an analytical method. The results are verified using expe- rimental modal techniques. Through the finite element and experimental modal approach free vibration analysis is carried out and natural frequencies are determined. Additionally, vibration accelerations of the structure are obtained by forced vibration analysis of themo- del. All calculations one performed on the new reconstructed structure, and it is determined whether the reconstructed structure satisfies the vibrational standards. Keywords: telescopic platforms, modal analysis, Finite ElementMethod, vibration 1. Introduction Platforms are crane-like machines that lift workers and their equipment to desired heights and over various distances. The word ’platform’ was only used to describe static structures such as bridges and ladders until the second half of the twentieth century. However, over the past 30 years, various types of platforms have been specified: • jointed platforms • trussed platforms • load platforms • telescopic platforms • vertical platforms In this study, we examine vibrations of telescopic platforms, which are widely used in con- struction areas, airports and harbours. Telescopic platforms are structures that have at least two long beams, with one sliding within the other, called booms. Usually, the second boom operates through hydraulic cylinders, and the other subsequent booms operate through chains. An example of a telescopic platformwith five booms is shown in Fig. 1. A survey of the literature reveals that many studies have been conducted using the finite elementmethod and three-dimensionalmodelling.Dayawansa et al. (2004) described cracks that grow in weld joints (called clusters), which protect the booms from catastrophic collapse, and themaintenance and repair techniques used to keep these joints in service. Karahan (2007) desi- gned and analysed a two-level telescopic crane using the finite elementmethod. The parts of the crane were designed in 3D using the Pro ENGINEER software program. The sheet thickness of themain stationary boomcarrying the loadwas determined byperforming stress analysis in the ANSYS workbench using the finite element method. Marjamaki and Makinen (2006) extended the idea of modelling a flexible telescopic boom using a non-linear finite element method in 3D. The boom was assembled using Reissner’s geometrically exact beam elements. The sliding 42 A. Yucel, A. Arpaci Fig. 1. An example of a five-boom telescopic platform boom parts were coupled together by the elements where the slide-spring was coupled to the beamwith the aid of themaster-slave technique. A special element with a revolute joint and an element with an offset were developed. Telescopic movement was achieved by varying the length of the element and the connecting chains. Ozkan (2005) analysed connection points of a frame crane and investigated stress distributions of the connection point components. The commer- cial finite element package ANSYS was used for finite element analysis. Themain objectives of the study conducted by Rusiński et al. (2006) were to discuss design problems associated with machines used in undergroundmining and to investigate the reasons why these problems arise in the cracked boom of an undergroundminemachine. Numerical and experimental approaches were pursued. The finite element method was used for numerical simulation. Fractographic and microscopic evaluation, chemical analysis and hardness tests were used to evaluate the mate- rials. The objectives were achieved by numerical simulation of a cracked loader boom, material evaluations of specimens and comparison of the results obtained from both approaches. Nu- merical simulations were performed based on a discrete model of a jib boom using predefined boundary conditions. Thefinite element analysis of the jib boomprovided information regarding stress distribution under extreme load conditions. The study involved macroscopic and fracto- graphic inspection, microscopic evaluation as well as hardness testing of the materials used for the jib boom. Erdol (2007) performed static finite element analysis and weight optimisation of a box girder, which constitutes approximately 50% of the total weight of gantry crane struc- tures. Trabka (2014) presented ten variants of a computational model for a telescopic boom crane that differs in the number and selection of flexible components. Modelling and numerical simulations were conducted using the finite element method. In the study, the compatibility of the numerical simulation results and test results of a real structure was qualitatively and qu- antitatively assessed. Time characteristics and frequency characteristics fter application of the discrete Fourier transformation were also analysed in the study. Posiadała and Cekus (2008) presented one degree of freedom discrete model representing vibration of the telescopic boom of a truck crane in the rotary plane. In the model, the influence of the hydraulic cylinder on the crane radius change was considered. Park andChang (2004) applied time delay control and commandless input shaping technique, which is a modification-based on the concept of Input Shaping Technique to increase the productivity of the boom of the telescopic handler. Lastly, Sochacki (2007), considered the dynamic stability of a laboratory model of the truck crane. In the study, the results in form of frequency curves for changing the geometry of the systemwere presented. In this study, vibrational analyses of telescopic platforms are conducted, and these structures are optimised to satisfy vibrational standards. Analytical and experimental vibration analysis of telescopic platforms 43 2. Models In this study, a telescopic platformwithfiveboomsandamaximumoperating height of 24mhas been selected formodelling. The booms aremodelled in two different cross-sections: rectangular and annular. The telescopic platform which is was constructed using annular cross sectional booms, is named the ’reconstructed structure’ in the study.All of the components of theplatform are modelled using the Pro/ENGINEER software. The model consists of the following main parts: foundation, tower, booms, basket joint and basket. The first part that is modelled is the foundation. The foundation is based on a 4920× 2100mm area, and profiles with cross- -sections measuring 80× 160× 6mm are used for modelling where 80mm represents height, 160mm represents width and 6mm represents thickness of the thin-walled rectangular section. The tower ismounted on the foundationusing a groupof gears located in the reduction gear box. The next part that is modelled is called the tower. The base flange of the tower has thickness of 20mm. It consists of 16×∅17 mmholes that are used tomount the gear box. The tower can rotate 360◦ around its axis, but its operation angle is limited to 180◦. The piston that connects the first boom to the tower is also modelled. The properties of the five booms modelled in this study are presented inTables 1 and 2 for the rectangular and annular cross-section, respectively. The solid models for the booms with rectangular and annular cross-sections are also presented in Figs. 2 and 3, respectively. Table 1.Dimensions of the booms with thin-walled rectangular cross-sections Boom No. Length ℓi [mm] Cross-section [mm] 1 4580 292×510×8 2 3600 250×422×6 3 3600 210×340×5 4 3600 170×260×5 5 3600 132×202×5 Table 2.Dimensions of the booms with thin-walled annular cross-sections Boom No. Length ℓi [mm] Cross-section [mm] 1 4580 ∅340×12 2 3600 ∅280×12 3 3600 ∅232×10 4 3600 ∅184×8 5 3600 ∅132×8 Fig. 2. A boomwith a rectangular cross-section 44 A. Yucel, A. Arpaci Fig. 3. A boomwith an annular cross-section One of the most important components of the model is the basket joint. The basket joint is the vital part that connects the last boom to the basket in which the worker operates. The last component of the model is the basket in which the work operates. The basket is modelled using ∅30×2.5mm round profiles. It has base area of 900×1500mm and height of 1120mm. The assemblies are constructed both for rectangular and annular section booms. 3. Finite element analysis for full assemblies After the assembled 3D solidmodel of the telescopic platform is obtained, it is imported into the commercial finite element analysis software programABAQUS for natural frequency andmode shape analysis. The approximate mesh size of the finite element model is 100mm. Themeshed finite element model is shown in Fig. 4. Linear tetrahedral solid elements are used in the mesh and thematerial properties are taken as follows: • density: 7850kg/m3 • Poisson’s ratio: 0.3 • modulus of elasticity: 210000MPa Fig. 4. Finite element model The first 10 natural frequencies are presented in Table 3. In Table 3, ’ip’ and ’op’ stand for the in-plane (XZ plane) and out-of-plane (XY plane) mode shapes, respectively. The source of the excitation is mainly the engine, and the origin of the excitation has been accepted as the foundation; therefore, we conducted the forced vibration finite element analysis by applying the force to the foundation of the platform. The operating (excitation) frequency of the system is 12.875Hz. This is the frequency of the system when the engine runs idle and the Analytical and experimental vibration analysis of telescopic platforms 45 Table 3.Natural frequencies Mode Natural frequency [Hz] Natural frequency [Hz] Mode No. (rectangular section) (annular section) shape 1 0.2987 0.2515 ip 2 0.4196 0.2668 op 3 1.1249 1.0035 ip 4 1.6382 1.0812 op 5 4.9468 4.1055 ip 6 7.1794 4.4389 op 7 12.125 10.105 ip 8 16.929 10.988 op 9 21.803 18.631 ip 10 31.183 19.926 op workers are working in the basket. As shown in Table 3, the natural frequency is f =12.125Hz, which is very close to the operating frequency of the system. This indicates a risk of resonance under operating conditions. Therefore, the model has been reconstructed. After reconstruction (annular boom profile), it has been clearly revealed that there is no natural frequency close to the operating frequency of the system, which validates the reconstruction. 4. Analytical solution for the five-boom model For flexural modes, the boom is modelled as shown in Fig. 5. Fig. 5. Analytical model of the boom for flexural modes Let thedeflection in the y directionbeν(z,t).The equation of vibration for thebeamelement is given as EI ∂4ν ∂z4 +µ ∂2ν ∂t2 =0 (4.1) where µ is mass per unit length, ρ is mass density, A is cross-sectional area, t is time and EI represents the flexural stiffness. As known µ= ρA (4.2) and ν(z,t) =φ(z)sin(ωt) (4.3) for harmonic motion. Substituting Eq. (4.3) into Eq. (4.1) gives ∂4φ ∂z4 − µω2 EI φ=0 (4.4) The solution is φ(z) =Acosh λz ℓ +B sinh λz ℓ +C cos λz ℓ +Dsin λz ℓ (4.5) 46 A. Yucel, A. Arpaci whereA,B,C andD are the integration constants and λ= ℓ 4 √ µω2 EI (4.6) For a five-boom structure, the equations are arranged as below. The model of the booms of a telescopic platformwith a pointmass at the free end is shown in Fig. 6, whereM is mass of the point mass, and J is mass moment of inertia of the point mass with respect to the x-axis for in-plane and the y-axis for out-of-plane analysis φi(z)=Aicosh λiz ℓi +Bi sinh λiz ℓi +Cicos λiz ℓi +Di sin λiz ℓi i=1,2,3,4,5 (4.7) Fig. 6. Analytical model of the five-boom structure for flexural modes Geometric boundary conditions are φ1(0)= 0 dφ1 dz (0)= 0 (4.8) Transition boundary conditions are (i=1,2,3,4) φi(ℓi)=φi+1(0) dφi dz (ℓi)= dφi+1 dz (0) EIi d2φi dz2 (ℓi)=EIi+1 d2φi+1 dz2 (0) EIi d3φi dz3 (ℓi)=EIi+1 d3φi+1 dz3 (0) (4.9) Natural boundary conditions are EI5 d2φ5 dz2 (ℓ5)−ω 2J dφ5 dz (ℓ5)= 0 EI5 d3φ5 dz3 (ℓ5)+ω 2Mφ5(ℓ5)= 0 (4.10) For torsional modes, the boom is modelled as shown in Fig. 7. Fig. 7. Analytical model of the boom for torsional modes Let the twist angle about the z-axis be ϕ(z,t). The equation of vibration for the beam element is given as ϕ=ϕ(z,t) GC ∂2ϕ ∂z2 = ρIp ∂2ϕ ∂t2 (4.11) where GC is the torsional stiffness related to Saint-Venant’s principle. For harmonic motion, substituting Eq. (4.12)1 into Eq. (4.11)2 gives Eq. (4.12)2 ϕ= θ(z)sin(ωt) c2 ∂2θ ∂z2 +ω2θ=0 (4.12) Analytical and experimental vibration analysis of telescopic platforms 47 where c2 = GC Ip (4.13) The solution is θ(z)=Asin ωz c +Bcos ωz c (4.14) whereA andB are the integration constants. For the booms of the telescopic platform θi(zi)=Ai sin ωzi ci +Bicos ωzi ci c2i = GCi ρ(Ip)i i=1,2,3,4,5 (4.15) Geometric boundary conditions are θ1(0)= 0 θi(ℓi)= θi+1(0) i=1,2,3,4 (4.16) Transition boundary conditions are GCi dθi dz (ℓi)=GCi+1 dθi+1 dz (0) i=1,2,3,4 GC5 dθ5 dz (ℓ5)=0 (4.17) The results of the finite element analysis and analytical solutions for both rectangular and annular cross-sectional five-boom systems are given inTables 4-7. InTable 4, ’ip’ and ’op’ stand for the in-plane and out-of-plane mode shapes, respectively. The value of the point mass is 200kg, which is the sum of masses of the basket and the worker. The discrepancies in Tables have been calculated according to the formula given below Dis. [%]= Analytical−FEA Analytical ·100 Table 4. Flexural natural frequencies for rectangular cross-sections Rectangular section Rectangular section Rectangular Mode shape (five-boom without (five-boomwith section point mass) point mass) (full assembly) FEA Analytical Dis. [%] FEA Analytical Dis. [%] FEA 0.3045 0.3134 2.84 0.2987 ip 0.4286 0.4425 3.14 0.4196 op 1.3610 1.4180 4.02 1.1529 1.1924 3.31 1.1249 op 2.0196 2.1049 4.05 1.6864 1.7486 3.56 1.6382 op 5.1049 5.3411 4.42 5.1198 5.3358 4.05 4.9468 op 7.4014 7.7389 4.36 7.4375 7.7484 4.01 7.1794 op 12.027 12.649 4.92 12.291 12.884 4.60 12.125 op 17.324 18.258 5.12 17.714 18.629 4.91 16.929 op 22.285 23.643 5.74 22.862 24.182 5.46 21.803 op 31.995 34.076 6.11 32.811 34.881 5.93 31.183 op 48 A. Yucel, A. Arpaci Table 5. Flexural natural frequencies for annular cross-sections Annular section Annular cross-section Annular (five-boom without (five-boomwith cross-section point mass) point mass) (full assembly) FEA Analytical Dis. [%] FEA Analytical Dis. [%] FEA 0.2549 0.2691 5.28 0.2515 1.2790 1.3410 4.62 1.0224 1.0745 4.85 1.0035 4.4066 4.6309 4.84 4.2253 4.4469 4.98 4.1055 10.366 11.010 5.85 10.425 11.134 6.37 10.105 19.119 20.419 6.37 19.339 20.875 7.36 18.631 31.444 33.434 5.95 31.584 33.926 6.90 30.105 48.990 52.014 5.81 48.927 52.673 7.11 46.439 65.911 70.520 6.54 65.163 71.154 8.42 61.458 Table 6.Torsional natural frequencies for rectangular cross-sections Rectangular Rectangular cross-section cross-section (five-boommodel) (full assembly) FEA Analytical Dis. [%] FEA 61.67 63.71 3.20 60.5784 110.96 112.10 1.02 105.988 167.98 169.81 1.08 156.036 214.76 230.28 6.74 190.169 Table 7.Torsional natural frequencies for annular cross-sections Annular section Annular section (five-boommodel) (full assembly) FEA Analytical Dis. [%] FEA 76.44 79.47 3.81 74.7758 135.92 140.40 3.19 129.100 204.09 210.30 2.95 186.386 273.28 282.68 3.33 233.853 5. Experimental modal analysis To conduct forced vibration analysis using the finite element method, we need to determine the excitation force of the system. Due to the restrictions regarding the construction of the telescopic platform, it is impossible to locate a force transducer to measure the excitation force of the system. Instead, we measure the acceleration values of the foundation and basket. Then, we conduct a series of forced vibration analyses using the finite elementmethod to satisfy these acceleration valuesmeasuredat certain points using sensors on theplatform.Thus,weobtain the excitation force value required to further reconstruct the structure. The positions of the sensors on the systemare shown inFig. 8.AB&K4524B triaxial CCLDpiezoelectric accelerometer with frequency range of 0.25-3000Hz and sensitivity of 100mV/g has been used in the experiments. FFT analyses are conducted for 0-100Hz (800 lines – 0.125Hz resolution) with sampling rate of 256Hz (256 samples per second). The first triaxial accelerometer is located on the connection part between the foundation and the tower so we obtain the acceleration data for the foundation to create the simulation Analytical and experimental vibration analysis of telescopic platforms 49 Fig. 8. Locations of the sensors on the foundation and basket of forced vibration analysis. Secondly, another triaxial accelerometer is located on the floor of the basket to obtain the acceleration data for the basket in order to use in the forced vibration simulation.Thesedataobtainedby themeasurementson the foundationandbasket are thenused as reference values in the forced vibration analysis, and a series of forced vibration simulations are carried out to satisfy these reference values. The correct excitation force value is detected when we reach the same values on the foundation and basket as the reference values. This excitation force value which is obtained from forced vibration simulations is then used in the forced vibration simulation of the reconstructed platform model (annular boom profile). Thus, bothmodels have been excited by the same and correct excitation force for the forced vibration simulations. The results of spectral analyses of the acceleration data obtained by the sensors on the foundation and basket are shown in Figs. 9 and 10. Fig. 9. Spectral analysis of foundation vibration of the telescopic platform: (a)X direction, (b) Y direction, (c)Z direction 50 A. Yucel, A. Arpaci Fig. 10. Spectral analysis of basket vibration of the telescopic platform: (a)X direction, (b) Y direction, (c)Z direction The main units written at the top of the axes in Fig. 9 and Fig. 10 are m/s2. 2m means 2mm/s2 wherem stands formm. 500u means 500µm/s2 where u stands for µm. Using the results of spectral analysis, the acceleration values at the operating frequencyhave been determined. They are presented in Table 8. Table 8.Experimentally obtained acceleration values at the operating frequency Direction Foundation Basket ]mm/s2] [mm/s2] X 5.004 9.173 Y 24.455 5.494 Z 2.203 19.532 Having realised the forced vibration analysis using the finite element method to satisfy the acceleration values, the distributed excitation force is determined to be 8.52 · 10−6 ton/mm2 (0.0836MPa). This force has been used to analyse both assemblymodels (with rectangular and annular boom profiles). 6. Conclusions In this study, vibrational analysis of a telescopic platformhasbeen conducted.This structurehas been reconstructed to satisfy vibrational standards (applying to the industrial safety regulations) and shift resonance frequencies. The vibrational analyses are conducted using solid modelling, finite elements and an analytical method. The results of the analysis are also verified using the experimental modal technique. Analytical and experimental vibration analysis of telescopic platforms 51 The operating (excitation) frequency of the system is 12.875Hz. The table of natural frequ- encies of the original model indicates that there is a natural frequency value of 12.125Hz that is very close to the operating frequency of the system. This reveals a risk of resonance under operating conditions. After reconstruction, it has been clearly revealed that there is no natural frequency close to the operating frequency of the system, which validates the reconstruction. Although it is impossible to locate a force transducer on the system and to measure the acting force, the distributed force has been determined to be 8.52 ·10−6 ton/mm2 (0.0836MPa) usingexperimentalmodal analysis by taking theacceleration values obtained experimentally into account. We measured the accelerations in different points of the system and then conducted a series of forced vibration finite element analyses with different force values until we achieved the acceleration values obtained by the experiments. This force value can be used in anymodal analysis of this model. By examining the related standard, it has been observed that the acceleration values on the basket are very high for workers. After the reconstruction, we observed a significant reduction in the acceleration values. The acceleration values on the basket before and after reconstruction are presented in Table 9. According to the related standard (ISO 2631), which defines the maximum allowed acceleration values for a worker, the acceleration values on the basket after reconstruction stay considerably under the limits for the operating frequency. Table 9.Comparison of acceleration values on the basket Direction Rectangular cross-cection Annular cross-section (original) [mm/s2] (reconstructed) [mm/s2] X 9.597 1.358 Y 5.709 1.267 Z 20.636 3.528 Tables 4-7 indicate thatfive-boomanalyticalmodels canbeaccepted insteadof full assemblies because parts other than the booms have little effect on the frequencies. Therefore, we can agree that the telescopic platformcanbe taken as a connection of beamswithvarying cross-sections for frequency calculations. The results also show that the point mass, which replaces themasses of thebasket andworkers in theanalyticalmodel, causes very little differenceonnatural frequencies but only changes the mode shapes. The point mass has no effect on torsional modes. Acknowledgments We want to thank Ms. Elif Naz Aladag and Mr. Mehmet Ozaltinoglu for their supports in the preparation of solid models and analyses files. References 1. Dayawansa P., Chitty G., Kerezsi B., Bartosiewicz H., Price J.W.H., 2004, Fracture mechanics of mining dragline booms, Structural Integrity and Fracture: Proceedings of the Inter- national Conference, SIF2004, Brisbane, Australia 2. Erdol T., 2007, Design, analysis of the gantry crane with finite element method and box girder optimization, Master’s Thesis, Gebze Institute of Technology, Gebze, Turkey 3. Karahan M., 2007, Design and finite element analysis of two levels telescopic crane, Master’s Thesis, Ataturk University, Erzurum, Turkey 4. MarjamakiH.,MakinenJ., 2006,Modelling a telescopicboom–the3Dcase:Part II,Computers & Structures, 84, 29, 2001-2015 52 A. Yucel, A. Arpaci 5. Ozkan I., 2005,Computer aided design and analysis of frame crane,Master’sThesis, DokuzEylul University, Izmir, Turkey 6. Rusiński E., Czmochowski J. Moczko, P., 2006, Numerical and experimental analysis of a mine’s loader boom crack, Journal of Achievements in Materials and Manufacturing Engineering, 17, 1/2, 273-276 7. Sochacki W., 2007, The dynamic stability of a laboratory model of a truck crane, Thin-Walled Structures, 45, 927-930 8. Posiadała B., Cekus D., 2008, Discretemodel of vibration of truck crane telescopic boomwith consideration of the hydraulic cylinder of crane radius change in the rotary plane, Automation in Construction, 17, 245-250 9. Park J.Y., Chang P.H., 2004,Vibration control of a telescopic handler using time delay control and commandless input shaping technique,Control Engineering Practice, 12, 769-780 10. TrabkaA., 2014,Dynamics of telescopic craneswith flexible structural components, International Journal of Mechanical Sciences, 88, 162-174 Manuscript received July 16, 2014; accepted for print June 20, 2015