Jtam.dvi JOURNAL OF THEORETICAL AND APPLIED MECHANICS 49, 3, pp. 927-943, Warsaw 2011 NOVEL SHAPE MEMORY ACTUATORS Hisaaki Tobushi, Kouji Miyamoto, Yasuhiko Nishimura, Kento Mitsui Aichi Institute of Technology, Department of Mechanical Engineering, Toyota, Japan e-mail: tobushi@aitech.ac.jp Inorder todevelopnovel shapememoryactuators, the torsionaldeforma- tionof a shapememoryalloy (SMA) tapeandtheactuatormodelsdriven by the tapewere investigated.The shapememory composite (SMC)belt composed of SMA tapes and a shapememory polymer (SMP)was fabri- cated, and the three-way bending characteristics were also investigated. The results obtained can be summarized as follows. In the SMA tape subjected to torsion, the martensitic transformation appears along the edge of the tape due to elongation of the edge of the tape and grows to the central part. The fatigue life in both the pulsating torsion and alternating torsion is expressed by a unified relationship of the dissipa- ted work in each cycle. Based on the two-waymotion of an opening and closing door model and a solar-powered active blind model driven by two kinds of SMA tape, it is confirmed that the two-way rotary driving actuator with a small and simple mechanism can be developed by using torsion of the SMA-tape. The SMC belt laminated with the SMP tape and SMA tapes was fabricated.The three-waybendingmovement of the SMCbelt was achieved during heating and cooling based on the charac- teristics of the SMA tapes and the SMP tape. The active SMC actuator with various three-dimentionalmovements canbe developedbyapplying the three-way properties of the SMC. Key words: shape memory alloy, shape memory polymer, composite, actuator, two-way, three-way, tape 1. Introduction In the recent years, intelligent materials having functions of sensing, judging and working have attracted worldwide attention. One of the main materials which have activated the research on the intelligent materials is the shape memory alloy (SMA) (Funakubo, 1987;OtsukaandWayman, 1998). Themain 928 H. Tobushi et al. characteristics of SMAare the shapememory effect (SME) and superelasticity (SE). Thanks to these characteristics, SMAs are used in the driving elements of actuators, heat engines and robots. The SME and SE appear as the result of a martensitic transformation (MT). The deformation properties of the SME and SE depend strongly on tem- perature and stress. In a recent study using the torsional deformation of a TiNi SMA tube, twist in the blades of rotor aircraft was investigated in order to improve the flight performance (Mabe et al., 2004, 2007). Because of the adaptable thermal response of SMA elements, thin wires and tapes are widely used in practical applications. In practical applications making use of SMA- tapes, the torsional deformation can be obtained simply by grippingboth ends without any mechanical process. If the characteristics of SE are exploited, a high performance of energy storage can be achieved similar to that of a torsion bar. In this way of using torsional characteristics of SMA-tapes, simple and small actuators can bedeveloped.The authors investigated therefore the basic deformation properties of an SMA-tape in torsion (Tobushi et al., 2008, 2009). The shape memory polymer (SMP) has been also practically used. In SMPs, the elastic modulus and the yield stress are high at temperatures be- low the glass transition temperature Tg and low at temperatures above Tg. If SMPs are deformed at temperatures above Tg and cooled down to temperatu- res below Tg by holding the deformed shape constant, the deformed shape is fixed andSMPs can carry large load. If the shape-fixed SMPelement is heated up to temperatures above Tg under no load, the original shape is recovered. The shape memory property appears based on the glass transition in which the characteristics of molecular motion vary depending on the variation in temperature. Among the SMPs, the polyurethane SMP has been practically used. In order to use new and higher functions by combining the excellent qu- alities of both the SMA and the SMP, the development of a shape memory composite (SMC) with the SMA and SMP is expected (Sterzl et al., 2003; Manzo and Garcia, 2007; Browne et al., 2009; Tobushi et al., 2006, 2010). In the present paper, in order to develop rotary actuators driven by SMA tapes, the torsional deformation properties of TiNi SMA tapes are investi- gated. The two-way motions of an opening and closing door model and a solar-powered active blindmodel driven by SMAtapes are demonstrated.The fabrication andmechanical properties of the SMCbelt which shows the three- way bending motion depending on temperature variation are investigated. Based on the three-way characteristics of the SMC belt, the SMC actuators with three-dimensional movement are also discussed. Novel shape memory actuators 929 2. Rotary actuator driven by SMA tape 2.1. Material Thematerials used in the experiment were Ti-50.18at%Ni SMA tapewith a thickness of t = 0.25mm and a width of w = 5mm. The specimen was a uniform flat tape of length L = 60mm. The gauge length of the specimen was l=40mm.The transformation temperatures obtained from theDSC test were Ms =304K, Mf =266K, As =319K and Af =359K. 2.2. Torsional deformation and fatigue properties of SMA tape 2.2.1. Twisted state The photographs of the twisted SMA tape are shown in Fig.1 for each angle of twist. The left side shows the fixed end and the right side the twi- sted end. The crossover point of the upper and lower surfaces of the SMA tape propagates from the twisting end at the angle of twist per unit length θ =39.3rad·m−1 (total angle of twist φ= π/2) and reaches the central part of the specimen at θ = 78.5rad·m−1 (φ = π). We note that both edges of the tape are elongated by twisting since both ends are axially fixed. There- fore, tensile stress is induced along both edges, and the stress state becomes different from the simple shear andmuch more complex. Fig. 1. Photographs of the twisted SMA tape at each angle of twist 2.2.2. Observation of martensitic transformation by thermography The thermomechanical characteristics of SMA appear due to theMT and the reverse transformation.The exothermic reaction and endothermic reaction 930 H. Tobushi et al. occur based on the MT and the reverse transformation, respectively. In the DSC test, the transformation temperatures are determined by measuring the heat change owing to these reactions. In the case of SE due to the stress- inducedMT, temperature increases or decreases in the loading and unloading processes, respectively. The initiation and growth processes of theMT can be therefore analyzed by measuring temperature on the surface of the material. The infrared thermography to measure the temperature distribution on the whole surfaceof thematerial canbeapplied to thisobjective.TheMTbehavior of SMA can be analyzed by the thermography (Pieczyska et al., 2006). The temperature distribution on the surface of the SMAtape at each angle of twist during the torsional deformation obtained by the infrared thermogra- phy is shown in Fig.2. In Fig.2, the upper side in each case shows the twisting part and the lower side shows the fixedpart.Themaximumtemperature Tmax on the surface of the specimen appears along the edge of the tape, and the exothermic MT occurs in this part and grows toward the central part of the specimen. The temperature rise along the edge of the tape starts at the angle of twist per unit length θ=26.2rad·m−1. This angle of twist per unit length corresponds to the tensile strain at the edge of the tape of 0.3% and coincides with the MT starting condition. The maximum temperature of the specimen occurs along the edge of the tape and the high temperature region propagates toward the central part with an increase in the angle of twist. Therefore, the MT grows preferentially based on the elongation along the edge of the tape. Fig. 2. Thermograms showing temperature distribution on the surface of the SMA tape appeared due to the phase transformation under torsion 2.2.3. Torsional deformation Therelationshipsbetween the torque M andangle of twist prunit length θ obtained by the pulsating torsion test and the alternating torsion test for the maximumangle θm =78.5rad·m −1 are shown inFigs.3a and 3b, respectively. Novel shape memory actuators 931 In the case of the pulsating torsion, the curve between M and θ is expressed almost by a straight line in the first loading process. In the unloading process, the initial slope of the curve is steep, and thereafter becomes to be the plateau stage. In the reloading process, the initial curve is almost parallel to the first loading curve, and thereafter the slope of the curve becomes steep. In the case of the alternating torsion, the twisting in the reverse direction to the first twisting direction was carried out. The reverse loading and unloading curves are almost similar to the first loading and unloading curves except for the early stage. That is, the first and reloading curves are closely symmetric with respect to the origin. In the reloading process, the initial slope of the unloading curve is steep and the plateau stage appears thereafter. The point at the end of the reloading curve almost coincides with the point at which the first unloading started, showing the return-pointmemory in the pulsating and alternating torsion. Fig. 3. Relationship between the torque M and angle of twist per unit length θ obtained by the pulsating and alternating torsion tests for the maximum angle θ m =78.5rad·m−1 The area surrounded by the hysteris loop of the torque-angle curve of twist shown in Fig.3 expresses the dissipated work per unit length Wd. The dissipatedwork Wd increases inproportion to themaximumangle of twist θm. The value of Wd in the alternating torsion is larger than that in the pulsating torsion by 3.5 times. Wd is very small if θm is smaller than a certain value in both alternating and pulsating torsion. 2.2.4. Torsional fatigue properties The relations between the maximum angle of twist per unit length θm and the number of cycles to failure Nf obtained from the torsion fatigue test are shown in Fig.4. The number of cycles to failure Nf decreases with an increase in the maximum angle of twist per unit length θm. This relation is 932 H. Tobushi et al. approximated by a straight line on the logarithmic graph. The fatigue life curve seems therefore to be expressible in an equation similar to that for TiNi SMAwires under bending. This can be seen in Eq. (2.1) θmN β f =α (2.1) where α and β represent θm in Nf =1 and the slope of the logθm− logNf curve, respectively. The calculated results obtained fromEq. (2.1) for β=0.1, α = 265rad·m−1 in pulsating torsion and for β = 0.13, α = 310rad·m−1 in alternating torsion are shown by the solid lines in Fig.4. As can be seen, the fatigue life curves are well matched by the solid calculation lines. Comparing the fatigue life of alternating torsion and pulsating torsion, the number of cycles to failure Nf for alternating torsion is smaller than that for pulsating torsion by 1/5. Fig. 4. Relationship between the maximum angle of twist per unit length and the number of cycles to failure The relationship between the dissipatedwork Wd and thenumber of cycles to failure Nf is shown inFig.5. The relationships for the pulsating torsion and the alternating torsion are located almost on the same line. The fatigue life in both the pulsating torsion and the alternating torsion is therefore expressedby a unified relationship. The relationship between Nf and Wd can be expressed by a power function in Eq. (2.2) WdN λ f =µ (2.2) where µ and λ represent Wd at Nf =1 and the slope of the logWd− logNf curve, respectively. The calculated result by Eq. (2.2) for λ = 0.382 and µ=9J/m is shownby the solid line in Fig.5. As can be seen, the overall incli- nations are approximated by the solid line. Thedissipatedwork corresponding Novel shape memory actuators 933 to the fatigue limit may exist at 0.04-0.05J/m. If the dissipated work in each cycle is smaller than 0.04-0.05J/m, the fatigue damage is slight, resulting in long fatigue life. Fig. 5. Relationship between dissipatad work per unit length and number of cycles to failure 2.3. Two-way opening and closing door model Photographs of the rotarymovement of an opening and closing doormodel using an SMA tape which shows the SME and an SEA tape which shows SE at RT under heating and cooling are shown in Fig.6. The SMA tape is the same as the specimen used in the torsion test. The SEA tape with a thickness of t=0.25mm and a width of w=2.5mm was a TiNi SEA tape which was heat-treated tomemorize a flat plane. In the initial state at RT, the SEA tape was mounted to be in a flat plane and the SMA tape was mounted at the total angle of twist φ=π/2. The SMA tapewas heated by joule heat through electric current. As can be seen in Fig.6, the door is closed in the initial state, since torque of SEA tape MSEA is larger than that of the SMA tape MSMA. Since the recovery torque appearsbyheating theSMAtape and the relation of the torque changes into MSMA >MSEA, the SMA tape recovers the flat plane and, therefore, the door is opened. When the SMA tape is cooled thereafter, the relation of torque varies again into MSMA < MSEA. Therefore, the SEA tape recovers the flat plane, resulting in closing the door. Thus, if two kinds of SMA tapes which show the SME and SE are used, a two-way rotary driving element with a small and simple mechanism can be developed. 934 H. Tobushi et al. Fig. 6. Photographs of two-way rotarymovement of a door driven by the SMA tape and SEA tape during heating and cooling 2.4. Solar-powered active blind model A new rotary actuator model in which the axes of an SMA tape and an SEA tape are arranged in parallel is demonstrated. The structure of a two-way actuator for opening and closing a blind driven by the SMAtape andSEAtape through sunlight, the photograph of the solar- powered active blind and the photographs of two-way motion of the actuator are shown in Figs. 7, 8 and 9, respectively. Both the SMA tape and the SEA tape were the same as those used in the door model. In the initial state, the SEA tape was mounted to be in a flat plane and the SMA tape was mounted at the total angle of twist φ=π/2. Fig. 7. Structure of the solar-powered active blind The SMA tape was heated by sunlight through a Fresnel lens. Since the recovery torque appears in the SMA tape by heating the tape, the blind is Novel shape memory actuators 935 Fig. 8. Photograph of the solar-powered active blind Fig. 9. Photographs of two-waymotion for the opening and closing of the blind driven by sunlight through the SMA tape and SEA tape closed through a crank and a lever. When the sunlight is shut out, the SMA tape is cooledandtheSEAtape recovers theflatplane, resulting in theopening of the blind. Thus, if two kinds of SMA tapes which show the SME and SE are used, the two-way rotary actuator driven by sunlight can be developed. 936 H. Tobushi et al. 3. Three-way active shape memory composite actuator 3.1. Material With respect to the SMA, two kinds of polycrystalline SMAtapes showing the SMEand SE at room temperature were used. The SMA tape showing the SME was a TiNi alloy tape with a width of 5mm and a thickness of 0.3mm produced by Furukawa Techno Materials Co. The SEA tape showing the SE was aTiNi alloy tape with awidth of 2.5mmand a thickness of 0.25mmpro- duced by Yoshimi Inc. In the shape memory processing, each SMA tape was set along the inside of a fixing ring with an inner diameter of 16mm and was heat-treated tomemorize the round shapewith an outside diameter of 16mm. The temperatures As and Af of the SMA tape were 324K and 342K, and these of the SEA tapewere 287K and 309K, respectively. TheR-phase trans- formation start and finish temperatures Rs and Rf of the SMA tape were 322K and 309K, respectively. With respect to the SMP, a polyurethane SMP sheet (MM6520) produced by SMPTechnologies Inc. was used. The thickness was 0.25mm and the glass transition temperature Tg was 338K. 3.2. Structure of SMC belt The SMC belt with a length of 60mm, a width of 10mm and a thickness of 1.03mm was fabricated by using two kinds of SMA tapes and three SMP tapes. In the fabricated SMC belt, the SMP tapes were used as a matrix and the SMA tapes as a fiber. The length of the SMA tape and the SEA tape was 50mm. Two kinds of SMA tapes were located in the central part of the SMC belt. The structure of the SMC belt is shown in Fig.10. 3.3. Fabrication of SMC belt At first, two incisions were given to one SMP tape and two kinds of SMA tapes (SMA tape and SEA tape) were passed through these incisions. In this process, the SMA tape and SEA tape were arranged facing in the opposite directions for the memorized round shape as shown in Fig.11. The SMP tape passed through two kinds of SMA tapes was sandwiched between two SMP tapes from the upper and lower sides. The combined material was set in the mold for fabricating the SMC belt. The upper and lower molds were fastened through the bolts by a compressive stress of 7.46MPa. The mold was held in the furnace at 448K for 60min followed by cooling in air. The SMC belt withoutbubbles andgaps among thematerials couldbe fabricatedunder these Novel shape memory actuators 937 Fig. 10. Structure of the SMC belt composed of the SMA, SEA and SMP tape Fig. 11. Arrangements of the SMA, SEA and SMP tapes to laminate the SMC belt conditons. In order to protect the projection of the edge by the recovery force of the SMAtapes, both edges of the SMAtapeswere connected by a thin steel clamp. 3.4. Three-way actuation The photographs of the three-way bendingmotion of the fabricated SMC belt during heating and cooling are shown in Fig.12. The heating and cooling were carried out between 293K and 365K. In Fig.12, the symbols As,SEA, Af,SEA, As,SMA, Af,SMA and Tg represent the reverse-transformation start and finish temperatures of the SEA tape and the SMA tape and the glass transition temperature of the SMP tape, respectively. At 293K 1O, the force induced in the SEA tape is high, and therefore the SMC belt bends in the 938 H. Tobushi et al. direction of the shape-memorized round shape of the SEA tape. If the SMC belt is heated 1O- 2O, the SMP becomes soft and the SMC belt bends further in the samedirection at temperatures around Tg 2O. If the SMCbelt is heated up above Tg 1O- 3O, the SMPbecomes easier to deform and the recovery force in the SMA tape increases at temperatures above Af,SMA (Lin et al., 1995), and therefore the SMC belt bends in the direction of the shape-memorized round shape of the SMA tape 3O. If the SMC belt is cooled thereafter 3O- 4O, the recovery force in the SMA tape decreases and the recovery force in the SEA tape becomes higher. Therefore, the SMCbelt bends again to its original shape 4O. Fig. 12. Photograph of the three-way bending deformation of the SMC belt during heating and cooling 3.5. Movement in three-point bending The three-way movement was measured by the three-point bending test. At first, the initial bent-form SMC belt was set on the supports of the three- point bending test machine. After setting the SMC belt, the point of the punchcontacted slightly the center of theSMCbelt.Keeping the slight contact conditionwith the contact load lower than 0.1N, the SMCbeltwas heated and cooled, and the displacement at the center of the SEC belt was measured. The relationship between the displacement and temperature obtained by the three-point bending test is shown in Fig.13. Rs,SMA and Rf,SMA denote the R-phase transformation start andfinish temperatures of theSMAtape, re- spectively. The symbols 1O- 4O correspond to the deformed states 1O- 4O shown Novel shape memory actuators 939 in Fig.12. It should be noticed that if the deflection of the SMCbelt increases, the center of the SMC belt moves downward and the displacement decreases to the negative side. In the heating process 1O- 2O, the deflection of the SMC belt increases, since the SMP exists in the glass transition region 2O and the SMP becomes soft. In the heating process 2O- 3O, the deflection of the SMC belt decreases, since the internal bendingmoment of the SMA tape increases at temperatures around Af,SMA due to the reverse transformation of the SMA tape. In the cooling process 3O- 4O, the deflection of the SMC belt increases gradually with a decrease in temperature since the internal bending moment of the SMA tape decreases due to the R-phase transformation and, therefore, the internal bending moment of the SEA tape becomes higher than that of other elements. Fig. 13. Relationship between the displacement and temperature of the SMC belt obtained by the three-point bending test 3.6. Recovery force in three-point bending In the three-point bending test with heating and cooling for the recovery force, the center of the SMC belt was put in the punch, and the position was held constant. Keeping the position of the center and two supports constant, the SMC belt was heated and cooled. The relationship between the recovery force and temperature obtained by the three-point bending test for the SMC belt is shown in Fig.14. The beha- vior of the recovery force is different between the heating process and cooling process, and the curve describes a large hysteresis loop. In the heating process, the recovery force of the SMCbelt decreases at temperatures around Tg of the SMP 2O. The recovery force starts to increase at temperatures around Af,SMA of the SMA tape. Since the recovery force of the SMA tape becomes stron- ger than that of the SEA tape at temperatures around Af,SMA, the recovery 940 H. Tobushi et al. force of the SMC belt appears. In the cooling process, the recovery force of the SMC belt decreases gradually. The recovery force of the SMA tape decre- ases due to the R-phase transformation at temperatures between Rs,SMA and Rf,SMA (Lin et al., 1995), and the recovery force of the SMC belt decreases correspondingly. Fig. 14. Relationship between the recovery force and temperature of the SMC belt obtained by the three-point bending test 3.7. SMC actuator with three-dimensional movement Thethree-waybendingmovement inaplanewas obtainedbythe fabricated SMCbelt. In the SMCbelt, the SMAtape andSEAtapewere arranged in the same direction and laminated with the SMP tape. If both tapes are arranged in different directions and sandwiched between SMP sheets, the SMC sheet moves not only in a plane but also moves in various planes during heating and cooling. Therefore, the SMC actuator with three-dimensional movement can be developed by applying the three-way properties of SMC with various combinations of the SMA, SEA and SMP elements. The three-dimensional movement properties of the SMC actuator depend on the memorized shapes, configurations, volume fractions and phase transformation temperatures of each element. 4. Conclusions In order to develop the rotary driving element with SMA tape, the torsional deformation properties and actuator models driven by a TiNi SMA tapewere investigated. The SMC belt composed of two kinds of SMAs and SMP was Novel shape memory actuators 941 fabricated, and the three-way movement and recovery force in bending were also investigated. The results obtained can be summarized as follows. • In the SMAtape subjected to torsion, theMTappears along the edge of the tapedue toelongation of the edgeof the tapeandgrows to thecentral part. The fatigue life in both the pulsating torsion and the alternating torsion is expressed by the unified relationship of the dissipated work in each cycle. • Based on the two-waymotion of the opening and closing doormodel and the solar-powered active blindmodel driven by two kinds of SMA tape, it is confirmed that the two-way rotary driving actuator with a small and simple mechanism can be developed by using torsion of the SMA tapes. • TheSMCbeltwas fabricated by laminating theSMPtape and twokinds of SMA tapes arranged facing in the opposite directions for the shape- memorized round shape. The three-way bendingmovement of SMCbelt was achieved during heating and cooling based on the characteristics of the SMA tapes and the SMP tape. The active SMC actuator with various three-dimensional movements can be developed by applying the three-way properties of the SMC. Acknowledgements The experimental work for this study was carried out with the assistance of stu- dents in Aichi Institute of Technology, to whom the authors wish to express their gratitude. The authors are also grateful to the administrators of Scientific Research (C) (General) in Grant-in-Aid for Scientific Research by the Japan Society for the Promotion of Science and The Naito ResearchGrant for financial support. References 1. Browne A.L. et al,, 2009, Programmable shims for manufacturing and as- sembly lines, U.S. Patent, 7538472B2, 1-24 2. FunakuboH. edit., 1987,ShapeMemoryAlloys,GordonandBreachScience, NewYork 3. Lin P.H., Tobushi H., Tanaka K., Lexcellent C., Ikai A., 1995, Reco- very stress ofTiNi shapememory alloy under constant strain,Arch.Mech., 47, 2, 281-293 942 H. Tobushi et al. 4. Mabe J.H.,Calkins F.T., Ruggeri R.T., 2007,Full-scale flight tests of air- craft morphing structures using SMA actuators,Proc. of SPIE, 6525-65251C, 1-12 5. Mabe J.H., Ruggeri R.T., Rosenzweig E., Yu C.J., 2004, Nitinol per- formance characterization and rotary actuator design, Proc. of SPIE, 5388, 95-109 6. ManzoJ.E.,GarciaE., 2007,Active rigidity smart joint for abat-wingmicro air vehicle,Proc. of ASME IMECE, 231-241 7. OtsukaK.,WaymanC.M., 1998,ShapeMemoryMaterials, CambridgeUni- versity Press, Cambridge 8. Pieczyska E.A., Gadaj S.P., Nowacki W.K., Tobushi H., 2006, Phase- transformation fronts evolution for stress- and strain-controlled tension tests in TiNi shape memory alloy,Exp. Mech., 46, 531-542 9. Sterzl T., Winzek B., Mennicken M., Nagelsdiek R., Keul H., Hoc- ker H., Quandt E., 2003, Bistable shape memory thin film actuators,Proc. of SPIE, 5053, 101-109 10. Tobushi H., Hayashi S., HoshioK.,MakinoY.,MiwaN., 2006,Bending actuation characteristics of shape memory composite with SMA and SMP, J. Intell. Mater. Syst. Struct., 17, 1075-1081 11. Tobushi H., Hayashi S., Sugimoto Y., Date K., 2010, Fabrication and two-way deformation of shapememory composite with SMA and SMP,Mater. Sci. Forum, 638-642, 2189-2194 12. Tobushi H., Pieczyska E.A., Nowacki W.K., Sakuragi T., Sugimoto Y., 2009,Torsional deformation and rotary driving characteristics of SMA thin strip,Arch. Mech., 61, 3-4, 241-257 13. Tobushi H., SakuragiT., SugimotoY., 2008,Deformation and rotarydri- ving characteristics of a shape-memory alloy thin strip element,Mater. Trans., 49, 1, 151-157 Nowe aktuatory z elementami z pamięcią kształtu Streszczenie W pracy zajęto się aktuatorami nowego typu, w których zastosowano stop z pa- mięcią kształtu (SMA) w postaci skręcającej się taśmy SMAwywołującej ruch aktu- atora. Opracowano kompozytowy pas (SMC) z taśm SMA oraz polimeru wykazują- cego efekt pamięci kształtu (SMP) oraz zbadano charakterystyki takiego kompozytu przy zginaniu trójosiowym.Rezultaty badań pokazały, że taśma SMApoddana skrę- caniu doznaje przemianymartenzytycznejwzdłuż krawędzi z powodu jej wydłużania, Novel shape memory actuators 943 która stopniowo przechodzi do środkowej części taśmy. Problemwytrzymałości zmę- czeniowej taśmy obciążonej jednokierunkowym i naprzemiennym skręcaniem opisano ujednoliconym wyrażeniem określającym pracę dyssypacji na każdy cykl obciążenia. Zbadano model aktuatora dwustronnego działania do otwierania i zamykania drzwi oraz do sterowania przesłony zasilanej energią słoneczną. Potwierdzono skuteczność torsyjnegoaktuatoraSMAprzyutrzymaniuprostotykonstrukcji takiegomechanizmu. Przeanalizowano przestrzenny ruch kompozytowego pasa SMC indukowanego ogrze- waniem i chłodzeniem w zależności od charakterystyk taśm SMA i SMP. Pokazano, że dzięki właściwościom kompozytu SMC różnych w trzech kierunkach, uzyskanie zdolności ruchowej aktuatora w przestrzeni (3D) jest możliwe. Manuscript received January 14, 2011; accepted for print March 3, 2011