Jtam.dvi JOURNAL OF THEORETICAL AND APPLIED MECHANICS 46, 4, pp. 799-811, Warsaw 2008 INVESTIGATION OF THE INFLUENCE OF SIMULTANEOUS VIBROACOUSTIC EXPOSURES ON THE OPERATOR Zbigniew Witold Engel AGH University of Science and Technology, Cracow, Poland e-mail: engel@uci.agh.edu.pl Piotr Kowalski Central Institute for Labour Protection, Warsaw, Poland e-mail: pikow@ciop.pl A new method of combined assessment of the influence of vibrations (hand-arm andwhole-body) and noise hazards simultaneously acting on employees is presented in the paper. Themethod has been developed on the basis of tests performed in selected means of road transportation. The investigations have shown that separate estimation of individual factors leads to unreasonable omission of a certain part of energy influ- encing the employee. The suggested assessmentmethod is based on the grounds of adding all kinds of the vibroacoustic energy. The application of thismethod allows one to take into considerationvibrations and noise occurring simultaneously, and due to this, the significant difference be- tween results of the hazard assessment at workplaces in comparison to results obtained by previously used standardisedmethods is revealed. Key words: mechanical vibrations, noise, assessmentmethod 1. Introduction Noise andmechanical vibrations are troublesome and hazardous factors of the everyday life. Approximately 33% of inhabitants of Poland is under the in- fluence of noise and vibrations in their workplaces, at home and even when resting. Noise and vibration hazards take a lead among all occupational ha- zards in the work environment. Investigations concerning noise and vibration hazards have been carried on for many years in Poland. However, there was no research on the simultaneous influence of noise and mechanical vibrations (hand-arm and whole-body). 800 Z.W. Engel, P. Kowalski The paper presents amethod of simultaneous assessment of hand-armand whole-body vibration hazards as well as noise hazard. The proposed method is based on appropriate additions of vibration and noise doses. Practical veri- fications were performed on the example of workplaces of drivers. Presently, any assessment of vibration and noise hazards of workers is being done on the basis of methods included in current standards. Methods of measuring and assessing given there assume a separate treatment of hand- arm and whole-body vibrations and noise. The basic parameters used for the assessment of such hazards are: • Daily exposure to hand-arm vibration: A(8), • Daily exposure to whole-body vibrations: A(8)=max{Ax(8),Ay(8),Az(8)}, • Level of daily noise exposures LEX,8h. Exposures tohand-armandwhole-bodyvibrations aredeterminedon thebasis of measured corrected accelerations of vibrations, while noise exposure levels on the basis of measured acoustic pressure. Taking into account the exposure only to one vibroacoustic factor, in the situation when all those hazards occur, means disregarding the part of energy (vibration or noise dose), which can additionally cause unfavourable health effects in the worker’s organism. Regardless of differences in influencing the human organism by hand-arm and whole-body vibrations and by noises, the estimation of combined exposures to those factors is possible due to appro- priate summing of the vibroacoustic energy. Undertaking this problem was additionally prompted by the European Union Directives considering the minimum requirements in health protection and safety of employees endangered by physical factors (vibration and noise). 2. Assessment of the simultaneous exposure The operator during his work is very often endangered by simultaneous influ- ence of hand-arm and whole-body vibrations and noise, i.e. by vibroacoustic factors. Each of these effects is a source of partial energy. Thus, the total vibroacoustic energy transferred into the human organism is the sum of the corresponding partial energies EWA = k ∑ j=1 Ej (2.1) Investigation of the influence of simultaneous... 801 where Ej is the partial energy. Equation (2.1) was used for development of the method of combined assessment of hazards caused by local and general vibrations and noise. It is assumed that the vibroacoustic energy influencing the worker EWA is proportional to the total dose D of vibration and noise EWA ∼D (2.2) The total dose D is a function of individual partial doses of vibrations and noise determined according to standards [13] D=F(DO,DM,DH) (2.3) where DO – dose of whole-body vibration DM – dose of hand-arm vibration DH – noise dose. The partial doses DO, DM, DH depend on the frequency f and on the exposure time. These parameters are determined by the following expressions DO = n ∑ i=1 a 2 Oi tOi (2.4) where aOi is determined from aOi = √ (1.4awOxi) 2+(1.4awOyi) 2+a2 wOzi and tOi is the action time of partial vibration accelerations awOxi, awOyi, awOzi, s DM = n ∑ i=1 a2MitMi (2.5) where aMi = √ a2 wMxi +a2 wMyi +a2 wMzi and tMi is the action time of partial vibration accelerations awMxi, awMyi, awMzi, s. The noise exposure is a value characterising the noise dose [13] EA =1.15 ·10 −5 ·100.1LEX,8h (2.6) where LEX,8h denotes the level of daily noise exposure. The general dependence used in the proposed method of the assessment of vibration and noise acting simultaneously is in the form of a sum of doses corrected by appropriate coefficients A,B,C D=ADO +BDM +CDH (2.7) 802 Z.W. Engel, P. Kowalski Due to the lack of permissible values for the combined assessment of vibroaco- ustic factors, it has been additionally assumed that taking into account the weighting filters Wh,Wd,Wk,A as well as permissible values given in current regulations will be possible in the proposedmethod. The permissible values for individual factors are introduced into Equation (2.6) in form of coefficients A,B,C. They are presented below together with values of the corresponding coefficients A(8)O,per =0.8 m s2 A= 1 DO,per = 1 A(8)2 O,per T0 = 1 0.82 ·28800 A(8)M,per =2.8 m s2 B= 1 DM,per = 1 A(8)2T0 = 1 2.82 ·28800 EA,per =3.64 ·10 3Pa2s C = 1 DH,per = 1 EA,per = 1 3.64 ·103 Thecorrected, bymeans of thepresentedabove coefficients, doses of vibrations and noise can be presented as multiplication factors of the permissible values of these doses KDO = DO DO,per KDM = DM DM,per KDH = DH DH,per Equation (2.6) will be then K =KDO +KDM +KDH (2.8) where KD was assumed as the assessment index of the total hazard of vibra- tions and noise acting simultaneously. On the basis of previous works concerning the indices of the vibration transfer and computer simulations, three alternative relationships were pre- pared for the combined method of assessment of vibrations and noise acting simultaneously: (2.9) and (2.10) KI = √ K2DM +K2DO +K 2 DH KII = ( n ∑ i=1 K n+3 4 i ) 4 n+3 (2.9) where n is the number of assessed factors, Ki – multiplication factor of the permissible dose determined for the factor i (e.g. KDO = K1, KDM = K2, KDH =K3). In the case of Equation (2.9)2, the factor n takes on a value between 1 and3, dependingon the number of vibroacoustic factors acting simultaneously (e.g. n=3whenhand-armandwhole-body, vibrations andnoise are assessed; n=2when e.g. only hand-arm vibration and noise are assessed). Investigation of the influence of simultaneous... 803 The results of several investigations indicate that reactions of the human organism to mechanical vibration and noise are not of the linear character. Therefore, for thedescription of the combined assessment, another dependence which represents this phenomenon more accurately than the linear function has been chosen KIII = log(10 K2 DM +10 K2 DO +10 K2 DH) (2.10) The values of indices of the assessment of the combined hazard of vibrations and noise K, KI, KII, KIII as functions of elements KDO, KDM , KDH are presented in Fig.1. Fig. 1. Indices K,KI,KII,KIII as functions of elements KDO,KDM ,KDH value Equation (2.10) can be applied for total ranges of individual partial ele- ments KDO, KDM , KDH however, due to properties of the assumed mathe- matical function, a physical interpretation is only possible when at least two elements (out of: KDO,KDM ,KDH) exceed 0.3. The index KIII is always above zero (KIII > 0). Since it is assumed that the criterion value is 1; a value of KIII lower than one means that the combined hazard is permissible, while above 1 means that the hazard is not acceptable (the combined hazard is considered small when eachmultiplication factor KDO,KDM ,KDH is smaller than 0.3). The index KIII below 1means additionally that none of the factors (hand-arm,whole-body vibrations, noise) exceed the permissible value when considered separately (in relation to the standard assessment method). However, KIII > 1 does not necessary mean that the permissible value for a single factor is exceeded, but might indicate high simultaneous intensity of several factors and the exceeding of the criterion value. 804 Z.W. Engel, P. Kowalski If we have a situation in which all three factors are 90% of the indivi- dually established permissible value (KDO = 0.9; KDM = 0.9; KDH = 0.9), the assessment performed on the basis of the standardised method will not indicate a hazard. The assessment will be the same as in the case of a hazard caused by one factor only, e.g. hand-arm vibration (KDO = 0; KDM = 0.9; KDH =0).Underestimation of the occupational risk is clearly visible in such a situation. This effect has been eliminated in the proposed combined method since the exceeding of the criterion value 1.0 will be assessed and KIII =1.287. The assumed criterion 1 does not mean increased requirements applied in the standardisedmethods. It can be similarly interpreted and classified for the estimation of the occupational risk KIII ∈        (0,0.5〉 − small risk (0.5,1.0〉 − medium risk (0,+∞) − high risk 3. Experimental studies The proposed energetic method was verified experimentally. Due to generally occurring vibration andnoise hazards atworkplaces of drivers, several vehicles representing various means of road transportation were chosen for the tests. The aim of the site tests was to recognise and compare vibroacoustic con- ditions in various vehicles most often met on Polish roads. In order to provide similar measuring conditions, the routes were selected in such a way as to have similar road conditions in relation to length, surfa- ce quality, usual driving speed as well as the proportion between city traffic and outside travelling (this proportionwas set 25%-75%).Measurements were performed at similar weather conditions. All tested trucks and lorries were loaded during the measurements, while buses, minibuses and coaches carried passengers. The site tests of hand-arm and whole-body vibration as well as noise oc- curring jointly in the same time were performed by simultaneous recording of vibration acceleration and acoustic pressure signals. A digital measuring recorder and accelerometers, microphone and appropriate pre-amplifiers were used (Fig.2). Investigation of the influence of simultaneous... 805 Fig. 2. Diagram of measuring set-up 4. Analysis of the obtained results The recorded signals of vibration acceleration and the acoustic pressure level were analysed and a set of frequency characteristics was prepared for each vehicle: vibration spectra on the steering wheel in the X, Y , Z directions; vibration spectra on the seat as well as the spectrum of the acoustic pressure. The results of vibration and noise analysis are presented on an example of a TIR-type truck (Fig.3). On the grounds of the determined spectra, the daily exposures to hand- arm vibration A(8) (Fig.4.), whole-body vibration A(8) (Fig.5) as well as exposure levels to noise LEX,8h (Fig.6) were determined. The following notations are introduced in Figs. 4, 5 and 6: A – Passenger car H – Dump truck B – Van I – Motor coach 1 C – Microbus J – Motor coach 2 D – Bus K – TIR 1 truck E – Small delivery truck L – TIR 2 truck F – Delivery truck M – TIR 3 truck G – Trunk lorry 806 Z.W. Engel, P. Kowalski Fig. 3. Vibration and noise spectra recorded for TIR 1 truck in motion Fig. 4. Daily exposures to hand-arm vibration A(8) On the basis of the determined exposure values (Figs. 4-6,) the assessment of vibration and noise hazards at the workplaces was performed (according to the binding regulations). Themultiplication factors of permissible values k (Table 1) were determined by referring the calculated vibration and noise exposures to the following Maximum Permissible Intensities (MPI): A(8)per =2.8m/s 2 – for hand-arm vibration A(8)per =0.8m/s 2 – for whole-body vibration LEX,8h,per =85dB – for noise Investigation of the influence of simultaneous... 807 Fig. 5. Daily exposures to whole-body vibration A(8) Fig. 6. Daily noise exposures LEX,8h The exceeding of theMPI valuewas found in one case only – for the trunk lorry (daily exposure to hand-armvibration of 2.85m/s2 exceeded the permis- sible value of 2.8m/s2, and the daily noise exposure being 87.5dB exceeded the permissible value of 85dB). On the basis of the recorded signals of vibration acceleration and acoustic pressure levels and in accordance with the binding standards, further asses- sment of the combined exposure was performed by the proposed newmethod. Values of the index KIII were calculated. Due to the same criterion value be- ing1, thevalues of theproposed combinedhazard index KIII cpuldbedirectly compared with the determined k values (multiplication factors of permissible values) according to PN-EN and the determined MPI. The same three-stage scale could also be applied to the occupational risk assessment. 808 Z.W. Engel, P. Kowalski Table 1. Selected parameters of vibration and noise estimated according to the standard methods Hand-arm Whole-body Noise vibration vibration D a il y ex p o su re A (8 ) [m / s2 ] M u lt ip li ca ti o n fa ct o r o f ex ce ed in g p er m is si b le v a lu e k D a il y ex p o su r A (8 ) [m / s2 ] M u lt ip li ca ti o n fa ct o r o f ex ce ed in g p er m is si b le v a lu e k D a il y ex p o su re le v el L E X ,8 h [d B ] M u lt ip li ca ti o n fa ct o r o f ex ce ed in g p er m is si b le v a lu e k M ea n s o f tr a n sp o rt a ti o n Passenger car 2.38 0.85 0.60 0.75 71.4 0.044 Van 2.03 0.73 0.63 0.79 70.4 0.035 Microbus 2.25 0.8 0.59 0.74 75.4 0.110 Bus 2.69 0.96 0.46 0.57 76.9 0.155 Small delivery truck 1.14 0.41 0.50 0.62 75.5 0.112 Delivery truck 1.88 0.67 0.48 0.60 71.3 0.043 Trunk lorry 2.85 1.02 0.77 0.97 87.5 1.778 Dump truck 1.48 0.77 0.77 0.97 84.2 0.832 Motor coach 1 1.14 0.41 0.50 0.62 74.6 0.091 Motor coach 2 1.47 0.53 0.32 0.40 73.3 0.068 TIR 1 truck 1.55 0.55 0.55 0.69 71.7 0.047 TIR 2 truck 1.87 0.67 0.60 0.75 73.1 0.065 TIR 3 truck 1.06 0.38 0.38 0.47 71.5 0.045 The calculated values of indices KIII and kmax (being for a given vehicle the highestmultiplication factor of the permissible value calculated separately for an individual vibroacoustic signal) as well as hazards determined by both methods – are presented inTable 2.The relative differences between KIII and kmax values allow one to compare quantitatively the results obtained by both methods. According to the expectations, in all the examined cases the assessment performed by the combined method shows an apparent hazard increase as compared to the hazard determined by the standardised method. Out of 13 workplaces assessed by the standardised method, only at one place the hazard exceeded the MPI value (trunk lorry: 1.78 – large hazard); at 11 places the hazard was medium and at one place the hazard was small. Investigation of the influence of simultaneous... 809 Table 2.Vibrations andnoise hazard assessment determinedby the combined method as well as by the standardised method – at the driver’s workplace of various means of road transportation KIII Hazard kmax Relatve determined Hazard difference by the determined between combined according KIII and assessment to PN-EN kmax method [%] M ea n s o f tr a n sp o rt a ti o n Passenger car 1.35 large 0.85 medium 37.0 Van 1.19 large 0.79 medium 33.6 Microbus 1.19 large 0.8 medium 32.8 Bus 1.12 large 0.96 medium 14.3 Small delivery truck 0.83 medium 0.62 medium 25.3 Delivery truck 0.90 medium 0.67 medium 25.6 Trunk lorry 3.17 large 1.78 large 43.8 Dump truck 1.53 large 0.97 medium 36.6 Motor coach 1 0.78 medium 0.62 medium 20.5 Motor coach 2 0.68 medium 0.53 medium 22.1 TIR 1 truck 1.00 medium 0.69 medium 31.0 TIR 2 truck 1.13 large 0.75 medium 33.6 TIR 3 truck 0.71 medium 0.47 small 33.8 When the same places were assessed by the combinedmethod, at 7 places the hazard was found to be large, and in 6 a medium one. The hazard estimated by the combined method in one case changed from small to medium and in 6 cases from medium to large as compared with the standardised method of assessment. In the remaining 6 cases, the hazard estimated by both methods was classified the same, however the relative differences between KIII and kmax were between 20.5% (formotor coach 1) and 43.8% (for the trunk lorry). For all 13 tested workplaces those differences were within the range between 14.3% (for the bus) and 43.8% (for the trunk lorry). 5. Conclusions On the basis of multiple tests performed at the Central Institute of Labour Protection, the authors proposed an energetic technical assessment method 810 Z.W. Engel, P. Kowalski of hazard endangering employees who are simultaneously influenced by hand- armandwhole-bodyvibrations andnoise. Themethod is based on summation of the so called „doses” which are determined by measurements. The sum of doses determined bymeasurements is corrected by appropriate coefficients A, B,C, which are developed by taking into consideration the permissible values given in the standards (separately for each factor). The coefficients A, B, C proposed in Eq. (2.7) can also be determined by means of the Singular Value Decomposition (SVD),whichwillbe thenext stepof thepresented research.To reach this aim, amatrix of partial doses and objects of tests will be developed (the so called observation matrix). This matrix will be decomposed by the SVD technique into three specific matrices, in which the same information on relationships between partial doses, as in the observation matrix, will be included, however, obtained bymeans of orthonormal vectors. Thus, it will be possible to reduce the developed simulationmodel by applying an appropriate approximation order.Expectedly, thenewly formedmatriceswill enable one to obtain identical numbers for all tested objects and for each individual index. Those numbers treated as the correcting indices will be used for the global assessment of vibroacoustic hazard. References 1. AugustyńskaD., Kowalski P., 2006, Strategia ochronypracownikówprzed drganiami mechanicznymi według nowych przepisów prawnych – europejskich i krajowych,Bezpieczeństwo Pracy, 5, 8-11 2. Dobry M.W.,1997, Optymalizacja przepływu energii w systemie człowiek- narzędzie-podłoże (CNP), Rozprawahabilitacyjna,PolitechnikaPoznańska,Po- znań 3. Engel Z., Kowalski P., 2000, Evaluation indices of exposure to vibration, Machine Dynamice Problems, 24, 3, 21-33 4. Engel Z., Kowalski P., 2001, Ocena ekspozycji drganiowej przy zastosowa- niu wskaźników,Mechanika, 83 5. EngelZ.,ZawieskaW.,KowalskiP., 2001,Możliwościwskaźnikowejoceny ryzyka ze względu na drgania, Materiały z 12 Międzynarodowej Konferencji „Noise Control’01, 24-26 6. Griffin M.J., 1990, Handbook of HUMAN VIBRATION, Academic Press, HarcourtBraceJovanovich,PublishersLondon,SanDiego,NewYork,Berkeley, Boston, Sydney, Tokyo, Toronto Investigation of the influence of simultaneous... 811 7. Kowalski P., 1999, Badania przenoszenia drgań w układzie ręka operatora- rękojeść,Materiały XLVI Otwartego Seminarium Akustyki OSA’99 8. KowalskiP., 2000,Wpływamplitudy i częstotliwości sygnałuwymuszającego na przenoszenie drgań z rękojeści narzędzia do ręki operatora,Materiały XLVII Otwartego Seminarium Akustyki OSA 2000, 493-496 9. Kowalski P., 2001, Wskaźniki przenoszenia drgań w układzie narzędzie-ręka operatora, Praca doktorska, Centralny Instytut Ochrony Pracy – Państwowy Instytut Badawczy,Warszawa 10. Kowalski P., 2006, Pomiar i ocena drgańmechanicznychw środowisku pracy według nowych przepisów prawnych,Bezpieczeństwo Pracy, 9, 24-26 11. Kryter K.D., 1985, The Effects of Noise on Man, Academic Press, Inc., London 12. Mansfield N.J., Griffin M.J., 1998, Effect of magnitude of vertical whole- bodyvibrationonabsorbedpower for the seatedhumanbody,Journal of Sound and Vibration, 215, 4, 813-825 13. Polskie normy: PN-N-01307:1994, PN-ISO 9612, PN-EN 14253:2005, PN-EN ISO 5349:2004 14. Rozporządzenie Ministra Pracy i Polityki Społecznej z dnia 29 listopada 2002r. w sprawie najwyższych dopuszczalnych stężeń i natężeń czynników szkodliwych dla zdrowia w środowisku pracy, Dz.U. Nr 217, poz. 1833., zm. Dz.U. 2005, nr 212, poz. 1769 This paper is dedicated to Professor Józef Nizioł on His 70th Birthday. Badania wpływu jednoczesnych ekspozycji wibroakustycznych na operatora Streszczenie Wartykule przedstawiono nowąmetodę oceny łącznej drgań (miejscowych i ogól- nych) i hałasu działających równocześnie na pracowników.Opracowano ją na podsta- wie wynikówbadań przeprowadzonychwwybranych środkach transportu drogowego. Badania wykazały, że niezależna ocena działających poszczególnych czynnikówwiąże się z nieuzasadnionym pomijaniem w ocenie części energii wibroakustycznej dociera- jącej do pracownika. Proponowana metoda oceny opiera się na zasadzie sumowania energii wibroakustycznej. Zastosowanie opisanej metody pozwala na uwzględnienie jednoczesnego działania drgań i hałasu; powoduje to istotne różnice wyników oceny narażenia czynnikami wibroakustycznymi na stanowisku pracy w stosunku do wyni- ków uzyskanych dotychczasowymimetodami znormalizowanymi. Manuscript received March 12, 2008; accepted for print May 19, 2008