Jtam-A4.dvi JOURNAL OF THEORETICAL AND APPLIED MECHANICS 57, 1, pp. 167-178, Warsaw 2019 DOI: 10.15632/jtam-pl.57.1.167 APPLICATION OF LINEAR SIX-PARAMETER SHELL THEORY TO THE ANALYSIS OF ORTHOTROPIC TENSEGRITY PLATE-LIKE STRUCTURES Paulina Obara Kielce University of Technology, Faculty of Civil Engineering and Architecture, Kielce, Poland e-mail: paula@tu.kielce.pl Application of the linear six-parameter shell theory to the analysis of orthotropic tense- grity plate-like structures is proposed in the paper. A continuum model of a tensegrity plate with the self-stress state included is used. The tensegrity module, which is based on 4-strut expanded octahedron modules with additional connecting cables is proposed as an example. Different planes of support of the structures are taken into account and thus dif- ferent reference surfaces of the plate model are considered. The self-stress state and some geometrical parameters are introduced for parametric analysis. Keywords: linear six-parameter shell theory, tensegrity plate-like structures, self-stress state 1. Introduction The concept of tensegrity structures covers trusses consisting of isolated compressed elements (struts) inside a continuous net of tensioned members (cables) (Motro, 2003; Skelton and Oli- veira, 2009). The specificity of these structures lies in infinitesimal mechanisms balanced with self-stress states. Tensegrity as a structural system offers many advantages over conventional structural systems. Proper actuation can keep it stiff during deployment without requiring external members, which is the main benefit of the system. The tensegrity concept has found applications in civil engineering structures such as towers (Schlaich, 2004; Gilewski et al., 2015), bridges (Gilewski and Kasprzak, 2011) and domes (Gómez-Jáuregui, 2010). Tensegrity based on spatial reticulated systems are double-layer tensegrity grids (Gómez-Jáuregui et al., 2012) with two parallel horizontal networks of members in tension forming the top and bottom layers. The grid nodes are linked by vertical and inclined bracingmembers in compression and tension. These systems can be treated as tensegrity plate-like structures. Examples are Kono’s struc- ture (Kono et al., 1999) and Blur building (Crawfordt, 2016; Gilewski et al., 2016). Tensegrity plate-like structures can also be builtwith tensegritymodules, such as a simplex or an expanded octahedron. Even very simple tensegrity structures have complex geometry and unique features. Their structural behaviour can be explained using a continuum model of a three-dimensional tensegrity plate-like structure (Al Sabouni-Zawadzka et al., 2016). In the paper, a continuum model of the plate is used. The model includes the effect of self-stress initially applied to the tensegrity structure. In the analysis, a linear six-parameter shell theory (Chróścielewski et al., 2004; Pietraszkiewicz, 2016) is proposed. In considerations, the shell theory is simplified by assuming that the plates have no curvature. As a result, the two-dimensional plate model for moderately thick plates is obtained for both membrane and bending deformations. Additionally, different planes of support of tensegrity plate-like struc- tures are taking into account, thus different reference planes of the plate model – the lower surface, themiddle surface and the upper surface are considered. The proposed approach allows one to analyse the influence of self-stress states and some geometrical parameters on average displacements, strains and internal forces in the structures. 168 P. Obara Themodel used in the paper is valid for all structures composed of tensegrity modules with orthotropic properties. 2. Material and methods 2.1. Linear six-parameter shell theory for the orthotropic model Developments of the theory of elastic shells have beenwidely discussed in papers andmono- graphs. In the paper, the six-parameter (six-field) shell theory is used (Burzyński et al., 2016; Chróścielewski et al., 2004, 2011, 2016; Pietraszkiewicz, 2016;Witkowski, 2011). This kinematic model is formally equivalent to theCosserat continuumwith six independentdegrees of freedom: three translations and three rotations (with the drilling degree of freedom). It is assumed that translations and rotations are small, i.e., the linear six-parameter shell theory can be used. As one of the first, the linear constitutive equation for Cosserat continuum was derived by Nowac- ki (1971). In this approach, the linear six-parameter shell theory is applied to the analysis of tensegrity plate-like structures. The rectangular plate of a constant thickness h in theCartesian coordinate system (x1,x2,z) is considered (Fig. 1). According to theHencky-Boole kinematic hypothesis, a displacement field in the 3D space is described as ũ(xα,z)=u(xα)+zβ(xα) for α =1,2 (2.1) where u is the translation vector andβ is the rotation vector of the reference surface (2D) u(xα)= [uα,w] T β(xα)= [φα,ψ] T (2.2) The proposed approach, compared to the classical five-parameter theory, includes additionally third independent non-vanishing rotation – the drilling degree of freedom ψ (rotation about the normal to the surface). Fig. 1. Geometry of a 3D plate-like body In a plate, there is no curvature, wchichmeans that the curvature of tensors is equal to zero, consequently, a model analysed in the paper is simpler than that shown by Chróścielewski et al. (2004) and by Pietraszkiewicz (2016). Consequently, the linear six-parameter shell theory is simplified. Below the reduced relations and equations are showed: — the kinematic relations γαβ = uα,β − ǫαβψ γα3 = φα+w,α καβ = φα,β κα3 = ψ,α (2.3) where γαβ, γα3, καβ, κα3 are the strain components and ǫαβ is the Ricci symbol, — the internal forces Nαβ = z2∫ z1 Sαβ dz Nα3 = z2∫ z1 Sα3 dz Mαβ = z2∫ z1 Sαβz dz Mα3 = z2∫ z1 Sα3z dz (2.4) Application of linear six-parameter shell theory to the analysis... 169 where Sαβ and Sα3 are the stress components, — the equilibrium equations Nαβ,α+fβ =0 Nα3,α+f3 =0 Mαβ,α+Nβ3+mβ =0 Mα3,α+ ǫαβNαβ +m3 =0 (2.5) where fβ, f3, mβ, m3 are the external loads. Internal forces (2.4) depend on the reference surface. In the paper, three different reference surfaces of the plate model are considered: the lower ΩL, the middle ΩM and the upper ΩU. In the mentioned approaches, the domains of the plate are defined as follows (Fig. 1) ΩL = {xK : xα ∈ Π −, z ∈ 〈z1,z2〉; z1 =0, z2 = h} ΩM = {xK : xα ∈ Π, z ∈ 〈z1,z2〉; z1 =−h/2, z2 = h/2} ΩU = {xK : xα ∈ Π +, z ∈ 〈z1,z2〉; z1 =−h, z2 =0} (2.6) Consequently, limitation of integrations (2.4) for each surface follows from the domains defini- tions. A complete six-parameter linear shell theory containing the drilling rotation ψ, two work- conjugate drilling bendingmeasures κα3 and two drilling couples Mα3 is presented in the paper. The constitutive equation for the linear theory of elasticity is expressed as Sij = DijklEkl i,j,k, l =1,2,3 (2.7) where Sij is the component of the stress tensor, Ekl is the component of the strain tensor and Dijkl is the component of the fourth-rank tensor of elasticity. In general, a tensor of elasticity contains 36 independent components, but taking into account the symmetry of strain energy 21 distinct components can be set out. The number of independent components is further re- duced if the material has symmetry planes. There are exactly eight different sets of symmetry planes (Chadwick et al., 2001). One of them is orthogonal symmetry (orthotropic material). This material requires 9 elastic constants in a two-dimensional case. In the paper, the orthotropic tensegrity plate-like structures based on the Reissner-Mindlin theory are discussed. For this model, the tensor of elasticity can be written as a matrix {Dijkl}≡d which contains 6 nonzero independent components B01111 = d11 B 0 2222 = d22 2B 0 2323 = d44 2B01313 = d55 2B 0 1212 = d66 B 0 1122 = d12 (2.8) The stress tensor and the strain tensor are written as Sij = { S11 S22 S23 S13 S12 }T Ekl = { E11 E22 2E23 2E13 2E12 }T (2.9) where E11 = γ11+zκ11 E22 = γ22+zκ22 E23 = 1 2 (γ23+zκ23 E13 = 1 2 (γ13+zκ13) E12 = 1 2 (γ12+γ21+zκ12+zκ21) (2.10) Stress components (2.9)1 are received fromconstitutive equations (2.7).Next, taking intoaccount the lower, middle and upper reference surfaces, the internal forces (2.4) are calculated N11 =h0d11γ11+h0d12γ22+h1d11κ11+h1d12κ22 N22 =h0d12γ11+h0d22γ22+h1d12κ11+h1d22κ22 N12 =h0d66(γ12+γ21)+h1d66(κ12+κ21) N13 =α0h0d55γ13+α1h1d55κ13 N23 = α0h0d44γ23+α1h1d44κ23 (2.11) 170 P. Obara and M11 = h1d11γ11+h1d12γ22+h2d11κ11+h2d12κ22 M22 = h1d12γ11+h1d22γ22+h2d12κ11+h2d22κ22 M12 = h1d66(γ12+γ21)+h2d66(κ12+κ21) M13 = α1h1d55γ13+α2h2d55κ13 M23 = α1h1d44γ23+α2h2d44κ23 (2.12) where hi (i = 0,1,2) are parameters depending on the reference surfaces (values are shown in Table 1) and αi (i =0,1,2) are shear correction factors. The problem of determining the shear factor was created in the Timoshenko beam theory, which takes into account the transverse shear deformation and the rotatory inertia (Khorshidi and Shariati, 2017; Obara andGilewski, 2016; Timoshenko andGere, 1961).Within the general six-parameter shell model used here, the shear correction factors α0 and α2 are introduced into the constitutive equations for the respective transverse shear stress resultants and stress couples (Chróścielewski et al., 1997). The values of two correction factors α0 =5/6 and α2 =7/10, with detailed derivation of these values,were arrivedbyPietraszkiewicz (1979). Themore information about the shear factors and the influence of different values of these factors on the results of static and dynamic behaviour of shell structures can be found in Chróścielewski et al. (2000). In the paper, additionally a correction factor α1 is introduced. This factor is significant if the lower surface or the upper surface is used as the reference plane. The closed form of the equilibrium equations for a plate (x1 ∈ 〈0,a〉 and x2 ∈ 〈0,b〉) and a plate strip (x1 ∈ 〈0,a〉 and x2 ∈ (−∞,+∞)) can be obtained by insertingEqs. (2.11) and (2.12) into Eq. (2.5). 2.1.1. Plate The behaviour at any point of the considered plate is defined by generalized displacementsq and the corresponding to them internal forces Q q=q(x1,x2)= [u1,u2,ψ,φ1,φ2,w] T Q=Q(x1,x2)=−[f1,f2,m3,m1,m2,f3] T (2.13) The first three displacements in (2.13)1 describe the membrane state and the last three – the bending state. In general, these states are coupled. Equilibrium equations (2.5) for the plate can be written as Lq=Q (2.14) where L=   h0L1 h0L4 0 h1L1 h1L4 0 h0L4 h0L2 0 h1L4 h1L2 0 0 0 α2h2L3 α1h1L5 α1h1L6 α1h1L3 h1L1 h1L4 −α1h1L5 h2L1−α0h0d55 h2L4 −α0h0L5 h1L4 h1L2 −α1h1L6 h2L4 h2L2−α0h0d44 −α0h0L6 0 0 α1h1L3 α0h0L5 α0h0L6 α0h0L3   (2.15) where L1 = d11 ∂2 ∂x21 +d66 ∂2 ∂x22 L2 = d66 ∂2 ∂x21 +d22 ∂2 ∂x22 L3 = d55 ∂2 ∂x21 +d44 ∂2 ∂x22 L4 =(d12+d66) ∂2 ∂x1∂x2 L5 = d55 ∂ ∂x1 L6 = d44 ∂ ∂x2 (2.16) Application of linear six-parameter shell theory to the analysis... 171 2.1.2. Plate strip The behaviour of the considered plate strip, with width a, is defined by generalized displa- cements q̃ and the corresponding to them internal forces Q̃ q̃= q̃(x1)= [u1,ψ,φ1,w] T Q̃= Q̃(x1)=−a 2[f1,m3,m1,f3] T (2.17) Equilibrium equations (2.5) for the plate strip can be written as L̃q̃= Q̃ (2.18) where L̃=   A0L̃1 0 A1L̃1 0 0 B2L̃1 aB1L̃2 B2L̃1 A1L̃1 −aB1L̃2 −a 2B0+A2L̃1 −aB0L̃2 0 B1L̃1 aB0L̃2 B0L̃1   (2.19) where L̃1 = d2 dξ2 L̃2 = d dξ ξ = x1 a Ai = hid11 Bi = αihid55 for i =0,1,2 (2.20) TheparametersAi andBidependon the reference surfaces.The formulasof theseparameters are shown in Table 1. For the plate strip, as in the case of the plate, the membrane state and the bending state are coupled. Table 1. Formulas of the parameters hi, Ai and Bi for the reference surfaces Parameters Lower surface Middle surface Upper surface h0 h h h h1 h 2/2 0 −h2/2 h2 h 3/3 h3/12 h3/3 A0 hd11 hd11 hd11 A1 h 2d11/2 0 −h 2d11/2 A2 h 3d11/3 h 3d11/12 h 3d11/3 B0 α0hd55 α0hd55 α0hd55 B1 α1h 2d55/2 0 −α1h 2d55/2 B2 α2h 3d55/3 α2h 3d55/12 α2h 3d55/3 Solving the set of differential equations (2.18) it is possible to obtain explicit formulas of the displacement and internal force. Thementioned formulas are described as follows u1(ξ)= C5+C6ξ+ 3A1 aA0 C4ξ 2− a2 2A0 f1ξ 2+ a3E1 6 f3ξ 3 ψ(ξ) = C7+C8ξ+ a2 2 (D1f3−D0m3)ξ 2 φ1(ξ)=− 1 a ( C2+2C3ξ+3C4ξ 2+ 6 a2B0E0 C4+ B1 B0 C8 ) − a B0 (1+B1D1)f3ξ − a3E0 6 f3ξ 3+aD1m3ξ+ 1 B0 m1− A1 A0B0 f1 w(ξ) = C1+C2ξ+C3ξ 2+C4ξ 3+ a4E0 24 f3ξ 4 (2.21) 172 P. Obara and N11(ξ)=− 2A1 a2 C3+ A0 a C6−af1ξ − A1 B0 (1+B1D1)f3+A1D1m3 N13(ξ)=− 6 a3E0 C4−af3ξ− A1 A0 f1+m1 M11(ξ)=− 2A2 a2 C3− 6 a2E0 C4ξ+ A1 a C6− aA1 A0 f1ξ+ a2 2 (A1E1−A2E0)f3ξ 2 − A2 B0 (1+B1D1)f3+A2D1m3 M13(ξ)=− 6B1 a3B0E0 C4+ 1 aD0 C8+a(B1D1−B2D2)m3ξ − A1B1 A0B0 f1+ B1m1 B0 (2.22) where Di = Bi B0B2−B 2 1 Ei = Ai A0A2−A 2 1 for i =0,1,2 (2.23) The results for the plate and plate strip can be used in analysis of different types of ortho- tropic systems, such as beams, plate strips, plates or more complicated multi-module plate-like structures. The displacement and internal force functions of these systems depend on the com- ponents of elastic matrix (2.8). To illustrate the proposed approach, a continuum orthotropic model of the tensegrity plate- -like structure is used. The internal and external plane of support of the structure is taken into account. For tensegrity systems, the components of the elastic matrix depend on stiffness of cables and struts and on the level of self-stress. 2.2. Orthotropic tensegrity plate-like structure The orthotropic model of a tensegrity plate-like structure is based on the energetic equ- ivalence between the discrete tensegrity repeatable element and the continuum model of the orthotropic material element shown in Fig. 2 (Al Sabouni-Zawadzka and Gilewski, 2016; Ke- biche et al., 2008). This approach can be used to a chosen structure of repeatable tensegrity elements creating plate-like structures. Fig. 2. Views of expanded four-strut octahedronmodules with additional cables (doted line) Application of linear six-parameter shell theory to the analysis... 173 A system of fully connected, repeating expanded four-strut octahedron modules with addi- tional cables (Al Sabouni-Zawadzka et al., 2016) is usedas an example.The system is orthotropic for the following geometric parameters x/X = 0.65, y/Y = 0.3 and z/Z = 0.56. This system consists of struts, regular cables and connecting cables, which are described by the following coefficients n = (EA)cable (EA)struct m = (EA)conection (EA)struct σ = S (EA)struct (2.24) where E is the Youngmodulus, A is cross section area and S is the axial force. The coefficients n and m describe the proportions of member properties, and σ describes the level of self-stress in tensegrity structures. The self-stress state is themost important feature of tensegrity structures. This state makes the structure as strong as the self-supporting structure and stabilizes the infinitesimal mecha- nisms occurred in tensegrity structures. The impact of the self-stress state in the structure is taken into account by using the geometric stiffness matrix. The coefficients of elastic matrix (2.8) of the tensegrity plate-like structure are as follows: d11 = 2EA h2 δ11 d22 = 2EA h2 δ22 d12 = EA h2 δ12 d44 = EA h2 δ23 d55 = EA h2 δ13 d66 = EA h2 δ12 (2.25) where EA =(EA)struct δ12 =0.845615n−0.105243σ δ11 =1+1.52325n+0.13125m+0.129225σ δ13 =1.26604n−0.153207σ δ22 =1+1.35912n+0.35m+0.137028σ δ23 =1.51283n−0.168813σ (2.26) 3. Results and discussion Displacements and the internal forces for tensegrity plate-like structures, as a function of pa- rameters (2.26), and, in consequence, coefficients (2.24) are determined. The jointly supported rectangular plate and plate stripswith different kinds of boundary conditions are discussed.The different planes of support in tensegrity plate-like structures are analysed. The results of the analysis are described using L for the lower surface, M for the middle surface and U for the upper surface. The displacements and internal forces are presented in the closed form. Displacements as a function of coefficients n and σ are presented in the form of graphs. Constants Ci (i = P,F,M) are not taken into account in the graphs. 3.1. Jointly supported rectangular plate The first example is the jointly supported plate with a sinusoidal load (Fig. 3) f3(x1,x2)=−q0 sin πx1 a cos πx2 b (3.1) Solving equation (2.14) by applying the Fourier sine and cosine series that satisfy the boun- dary conditions, leads to determining the displacements for the lower, themiddle and the upper surface. The closed form of solutions for the maximum deflection wmax = w(0.5a,0.5b) for a square plate (b = a) are as follows 174 P. Obara Fig. 3. Rectangular plate jointly supported wMmax = CP (144α20a 4β0+h 2π2β2+12α0a 2h2π2β3 α0(β1β2+β4) ) wLmax = w U max = CP (4(36α0α3a4β0+α2h2π2β2)β1+12a2h2π2(4α0α2β1β3−β5) α3(β1β2+β4)β1 ) (3.2) where CP = a2q0 EAhπ4 β0 = δ13δ23 β1 = δ13+ δ23 β2 = h 2π2[δ12(2δ22−3δ12)+2δ11(δ12+2δ22)] β3 = δ13(δ12+2δ22)+ δ23(δ12+2δ11) β4 =24α0a 2δ13δ23(δ11+ δ22+3δ12) β5 =3α 2 1[δ 2 13(δ12+2δ22)+ δ 2 23(δ12+2δ11)−4δ12δ13δ23] (3.3) For any rectangular plate, the decoupling of bending and membrane behaviour occurs only for the middle reference surface. It means that for this surface the displacements describing the membrane state are equal to zero: uM1 (ξ) = u M 2 (ξ) = ψ M(ξ) = 0. For the lower and the upper surface, the vertical displacements are the same (3.2)2, and themembrane displacements are as follows: uL1(ξ) = −u U 1 (ξ), u L 2(ξ) = −u U 2 (ξ) and ψ L(ξ) = −ψU(ξ). The rotations φα(ξ) do not depend on the reference surface: φL1 (ξ) = φ M 1 (ξ) = φ U 1 (ξ) and φ L 2(ξ) = φ M 2 (ξ) = φ U 2 (ξ). For the analysed plate, the displacements depend on three shear correction factors αi (i = 0,1,2) and on the parameter α3 =4α0α2−3α 2 1 (3.4) However, if the middle reference surface is considered only one shear factor α0 occurs. The paper refers to the application of the linear six-parameter shell theory to the analysis of orthotropic tensegrity plate-like structures. These systems are double-layer tensegrity grids. To establish values of the shear correction factors for such a plate, it is necessary to build and next to verify the propermodelwhich shouldbebased on the knowledge of themodelledmaterial and the phenomenon. The aim of future research will establish values of the three shear correction factors within the six-parameter linear theory of elastic tensegrity plate-like structures and test their influence on numerical results of static behavior of such structures. Now, to illustrate the influence of the reference plane on the behaviour of tensegrity structu- res, it is that the assumed values of the shear factors are: α0 =5/6, α2 =7/10 (Chróścielewski et al., 1997, 2000; Pietraszkiewicz, 1979; Witkowski, 2011; Woźniak, 2001) and α1 =8/10. The last correction factor has been assumed so that parameter (3.4) is positive definite. On the basis of Eq. (3.2), the influence of the self-stress and stiffness of cables and struts on the displacement in tensegrity plate-like structures can be estimated in a simple way. The parametric analysis canbe carried for anymoderately thickplates.As an example, results for the thickness to length ratio h/a =0.25, on the assumption m = n, are shown in Fig. 4. Formulas (3.2) are valid only for n > 0.2σ. Application of linear six-parameter shell theory to the analysis... 175 Fig. 4. Maximum deflection of the plate 3.2. Plate strips Thedisplacements and the internal forces for plate strips are determinedbasedonEqs. (2.21) and (2.22). These formulas depend on boundary conditions. Plate strips with the force mass f3(x1) =−q0 taken into account are studied. Three kinds of support, i.e., cantilever (Fig. 5a), simply supported (Fig. 5b) and clamped-clamped (Fig. 5c) are considered. The formulas of the maximum deflection are derived: — the cantilever plate strip wMmax = CM [ 6 1 δ11 + 4 α0 (h a )2 1 δ13 ] wLmax = w U max = CM [ 6 1 δ11 +16 α2 α3 (h a )2 1 δ13 ] (3.5) — the simply supported plate strip wMmax = CM [5 8 1 δ11 + 1 α0 (h a )2 1 δ13 ] wLmax = w U max = CM [1 4 1 δ11 +4 α2 α3 (h a )2 1 δ13 ] (3.6) — the clamped-clamped plate strip wMmax = CM [1 8 1 δ11 + 1 α0 (h a )2 1 δ13 ] wLmax = w U max = CM [1 8 1 δ11 +4 α2 α3 (h a )2 1 δ13 ] (3.7) where CM = −a 4q0/(8EAh). In these cases, the deflection functions depend on the correction factors αi (i =0,1,2,3) but for the middle references surface only on the factor α0. Fig. 5. Plate strips: (a) cantilever, (b) simply supported, (c) clamped-clamped For all analysed plate strips, displacements describing themembrane state are equal to zero only for themiddle reference surface: uM1 (ξ)= ψ M(ξ)= 0. For the lower and the upper surfaces, the axial displacement is a polynomial function of the degree three, and for each surface there is an equality: uL1(ξ)=−u U 1 (ξ). The drilling rotation is a polynomial function of the degree two and ψL(ξ)=−ψU(ξ). The rotations φα(ξ) do not depend on the reference surface, and for each surface: φL1(ξ)= φ M 1 (ξ)= φ U 1 (ξ) and φ L 2(ξ)= φ M 2 (ξ)= φ U 2 (ξ). For the cantilever and the clamped-clamped plate strip, the internal forces do not depend on the reference surface. Themembrane force and the drilling couple are equal to zero: N11(ξ)= 0, M13(ξ)= 0, and the transverse force and the bending couple are as follows: 176 P. Obara —the cantilever plate strip N13(ξ)=−aq0(1− ξ) M11(ξ)=− a2q0 2 (1+2ξ −ξ2) (3.8) — the clamped-clamped plate strip N13(ξ)=− aq0 2 (1−2ξ) M11(ξ)= a2q0 12 (1−6ξ+6ξ2) (3.9) For the simply supported plate strip, the transverse force and the bending couple do not depend on the reference surface, as for previous cases N13(ξ)=− aq0 2 (1−2ξ) M11(ξ)=− a2q0 2 (ξ − ξ2) (3.10) the drilling couple is equal to zero M13(ξ) = 0, but for the lower and the upper surface, the constant axial force occurs additionally NL11(ξ)=−N U 11(ξ)=− a2q0 8h NM11 (ξ)= 0 (3.11) Internal forces (3.8)-(3.11) do not depend on geometric and physical properties of tensegrity plate-like structures. Based on Eqs. (3.5)-(3.7), the influence of the self-stress and the stiffness of cables and struts on the displacement in tensegrity plate-like structures can be estimated. As an example, the parametric results, for h/a = 0.25, on the assumption m = n, are represented graphically in Figs. 6-8. Values of the correction factors are assumed like for the analysed jointly supported plate. Formulas (3.5)-(3.7) are specified only for n > 0.121σ. Fig. 6. Maximum deflection of the cantilever plate strip Fig. 7. Maximum deflection of the simple-supported plate strip 4. Conclusions The paper proposes the application of the linear six-parameter shell theory to the analysis of orthotropic tensegrity plate-like structures. The continuum model of the plate is used. The Application of linear six-parameter shell theory to the analysis... 177 Fig. 8. Maximum deflection of the clamped-clamped plate strip parametric analysis including the self-stress and selected geometrical parameters of tensegrity are considered. In the analysis, different planes of support of tensegrity plate-like structures are taken into account. The proposed approach helps one to understand unique properties and structural behaviour of tensegrities. Comparing the obtained results, it canbenoticed thatdisplacements dependon the reference surface. Additionally, the influence of the self-stress level on the displacements also depends on the reference surface – isbiggerwhenthe lower (or upper) surface is considered. Itmeans that the plane of support of tensegrity structures significantly affect the displacements. Furthermore, the results of parametric analysis shownthat the influenceof the self-stress level on thedisplacements decreases with an increase in the stiffness of cables (the parameter n increases). The closed form of the displacements and the internal forces obtained in the paper simplifies calculations. It is not necessary to describe thewhole complex tensegrity structureswith the use of computationalmethods.The closed formulas can beuseful in the design process and construc- tion of different types of tensegrity systems, such as beams, plates or more complex structures. Additionally, the obtained in the paper functions of the displacements and the internal forces can be used for analysis of orthotropic plate strips with any external loads and any boundary conditions. References 1. Al Sabouni-Zawadzka A., Gilewski W., 2016, On orthotropic properties of tensegrity struc- tures,Procedia Engineering, 153, 887-894 2. AlSabouni-ZawadzkaA.,GilewskiW.,Kłosowska J.,ObaraP., 2016,Continuummodel of orthotropic tensegrity plate-like structures with self-stress included, Engineering Transactions, 64, 4, 501-508 3. Burzyński S., Chróścielewski J., Daszkiewicz K., Witkowski W., 2016, Geometrically nonlinear FEM analysis of FGM shells based on neutral physical surface approach in 6-parameter shell theory,Composities Part B, 107, 203-213 4. Chadwick P., Vianello M., Cowin S.C., 2001, A new proof that the number of linear elastic symmetries is eight, Journal of the Mechanics and Physics of Solids, 49, 2471-2492 5. Chróścielewski J., Kreja I., Sabik A., Witkowski W., 2011,Modeling of composite shells in 6-parameter nonlinear theory with driling degree of freedom,Mechanics of Advanced Materials and Structures, 18, 403-419 6. Chróścielewski J., Makowski J., Pietraszkiewicz W., 2004, Statics and Dynamics of Mul- tifold Shell: Nonlinear Theory and Finite Element Method (in Polish), IPPTPAN,Warszawa 7. Chróścielewski J.,Makowski J., Stumpf H., 1997, Finite element analysis of smooth, folded andmulti-shell structures,Computer Methods in Applied Mechanics and Engineering, 41, 1-46 178 P. Obara 8. Chróścielewski J., Pietraszkiewicz W., Witkowski W., 2000, On shear correction fac- tors in the non-linear theory of elastic shells, International Journal of Solids and Structures, 47, 3537-3545 9. Chróścielewski J., Pietraszkiewicz W.,WitkowskiW., 2016,Geometrical nonlinear FEM analysis of 6-parameter resultant shell theory based on 2-D Cosserat constitutive model, ZAMM, 96, 2, 191-204 10. Crawfordt, 2016, Transgender Architectonics: The Shape of Change in Modernist Space, Ro- utledge, NewYork 11. GilewskiW.,KasprzakA., 2011,Tensegrities in bridge structures (inPolish),Acta Scientiarum Polonorum: Architectura, 10, 3, 35-43 12. Gilewski W., Kłosowska J., Obara P., 2015, Applications of tensegrity structures in civil engineering,Procedia Engineering, 111, 242-248 13. Gilewski W., Kłosowska J., Obara P., 2016, Verification of tensegrity properties of Kono structure and Blur Building,Procedia Engineering, 153, 173-179 14. Gómez-Jáuregui V., 2010,Tensegrity Structures and their Application to Architecture, Servicio de Publicaciones de la Universidad de Cantabria 15. Gómez-JáureguiV.,AriasR.,OteroC.,ManchadoC., 2012,Novel technique for obtaining double-layer tensegrity grids, International Journal of Space Structures, 27, 2-3,155-166 16. KebicheK.,KaziM.,AoualN.,MotroR., 2008,Continuummodel for systems in a self-stress state, International Journal of Space Structures, 23, 103-115 17. Khorshidi M.A., Shariati M., 2017, A multi-spring model for buckling analysis of cracked Timoshenko nanobeamsbased onmodified couple stress theory, Journal of Theoretical andApplied Mechanics, 55, 4, 1127-1139 18. KonoY., ChoongK.K., ShimadaT., KuniedaH., 1999,Experimental investigation of a type of double-layer tensegrity grids, Journal of the IASS, 40, 130, 103-111 19. Motro R., 2003,Tensegrity: Structural Systems for the Future, Kogan Page Science, London 20. Nowacki W., 1971,Theory of Asymmetrical Elasticity (in Polish), IPPTPAN,Warszawa 21. ObaraP.,GilewskiW., 2016,Dynamic stability ofmoderately thickbeams and frameswith the use of harmonic balance and perturbation methods, Bulletin of the Polish Academy of Sciences: Technical Sciences, 64, 4, 739-750 22. PietraszkiewiczW., 1979,Finite Rotations andLagrangeanDescription inTheNon-linear The- ory of Shells, Polish Scientific Publishers,Warszawa-Poznań 23. Pietraszkiewicz W., 2016, The resultant linear six-field theory of elastic shells: What it brings to the classical linear shell models?, ZAMM, 96, 8, 899-915 24. Schlaich M., 2004, The messeturm in Rostock – a tensegrity tower (in German), Journal of the IASS, 45, 145, 93-98 25. Skelton R.E., de Oliveira M.C., 2009,Tensegrity Systems, Springer, London 26. Timoshenko S.P., Gere J.M., 1961,Theory of Elastic Stability, McGraw-Hill, NewYork 27. Witkowski W., 2011, Synthesis of Formulation of Nonlinear Mechanics of Shells Undergoing Finite Rotations in the Context of FEM (in Polish),WydawnictwoPolitechnikiGdańskiej, Gdańsk 28. WoźniakC., 2001,Mechanics of Elastic Shells and Plates (in Polish), Polish Scientific Publishing House,Warszawa Manuscript received December 20, 2017; accepted for print September 2, 2018