Proceedings of Engineering and Technology Innovation, vol. 5, 2017, pp. 01 - 06 Innovative Security Technology for Optical Fiber Data Transmission Using Optical Vortex Marek Ε»yczkowski * , Konrad Dominik BrewczyΕ„ski, Mateusz Karol Institute of Optoelectronics, Military University of Technology, Warsaw, Poland . Received 10 July 2017; received in revised form 11 August 2017; accept ed 13 August 2017 Abstract This article presents system concept of the use of an optical vortex phenomenon for secure data exchange in the optical fiber line. Optical vortices are obtained in free space, and then they are introduced into the optical fiber. Their p roperties are e xa mined in the world [1-2], so far, wh ich directly shows the ability to increase the bandwidth of optical fiber. Given the structure and characteristics of the optical vorte x, the authors propose to set a secure optical link. Such link can be provided in two ways . The first method involves coding an information on optical vorte x. The data in the optical fiber line can be coded by time-position modeling of the optical properties of the vortex. In addition, changing the topology of the optical vortex and the use of mode dependencies also offer the possibility of information coding. The second way to use the vortex in the optical fiber is setting of optical fiber sensor, sensitive to the disturbance of fiber-optic trans mission line. It can be achieved by propagation both - coded informat ion in basic mode and an optical vorte x in a mic rostructural fiber. In the case of physical impact on optical fiber the vorte x disturbs the flow of data, forming the information noise on the output of the fiber. The artic le p resents the setup of the generation of optical vorte x, for the te leco mmunications bandwidth, developed at the Institute of Optoelectronics, in the Security Systems Group and initial tests of the setup . Keywor ds: optical vortex, fiber optic, safe communication 1. Introduction The work on obtaining and using optical vortices in teleco mmun ications fiber optic networks, undertaken at the Institute of Optoelectronics, is the result of global de mand for increasing the speed of informat ion flow and for increasing the security of data transmission. Each day the internet traffic increases. According to MINTS the interpolated growth of demand for data is linear since about 2007 and is projected to rema in so [3]. According to R.J. Essiambre and R.W. T kach we are inevitably approaching the limit of the capacity of optical fibers. The only solution is to search for new methods of data encoding and new possibilit ies of denser packing da ta. The solution may be optical vortices, which can propagate in telecommun ications optical fiber parallel to data coded current technical solutions. Space Division Multiple xing allows increasing the capacity of an optical fiber. There must be maintained appropriate conditions for the propagation of optical vortices. First of all optical vort ices propagate only multi-core optica l fibers [4]. Another proble m with working with optical vortices is their instability over long distances. Currently the world record to maintain a stable optical vortex is its propagation on distance 1.1 km [5]. * Corresponding author. E-mail address: marek.zyczkowski@wat.edu.pl Proceedings of Engineering and Technology Innovation, vol. 5, 2017, pp. 01 - 06 Copyright Β© TAETI 2 2. Optical Vortex Forming Setup To create an optical vorte x in the optical fiber, it is necessary to create it first in free space. For this purpose, the Gaussian beam must be used of a wavelength πœ† = 1550 π‘›π‘š . In order to generate a proper focused Gaussian beam we used: a laser (o f a wavelength πœ† = 1550 π‘›π‘š ), spatial filter and a pinhole. This bea m is introduced to the optical fiber with a length of 0.5 m by an FC-PC connector. The beam a fter leaving the fiber goes to the spatial filter. The spatial filter used in the setup is a lowpass filter and this means that peripheral parts of the beam, which contain high frequencies, are being cut. The principle of operation of a spatial filter is based on diffraction, where in the side bands are filtered off on pinhole, and only a ma in mod is transmitted further. The spatial filter has an aperture of adjustable dia meter and the dia meter used in the setup is 5 ΞΌm. (a) Scheme (b) Photo of the setup Fig. 1 The setup for an optical vortex forming There have been added a polarisation controlle r to the setup of generating the Gaussian beam. Po larised Gaussian beam is designed to fit the phase plate. Consequently, a beam is polarised in the horizontal direction. The beam, a fter passing through the phase plate, is delayed in phase from 0 do 2πœ‹ . We used the cell with the nematic liquid crystal 5CB in the setup forming the optical vorte x. It is div ided into 16 pieces, each of which is supp lied by a diffe rent voltage. This imp lies that each of the 16 pieces has a different refract ive inde x. Thanks to this the Gaussian beam, which propagates by the phase plate is gradually delayed, diffe rently for each piece of the plate. Depending on the number of pieces and the voltage applied to them the topology of the optical vortex changes [6]. Proceedings of Engineering and Technology Innovation, vol. 5, 2017, pp. 01 - 06 Copyright Β© TAETI 3 Fig. 1 shows the setup for optical vorte x forming which is set together at the Institute of Optoelectronics. The setup consists of (in order): ο‚· Laser, πœ† = 1550 nm, ο‚· Fiber optic Polarisation controller, ο‚· Lens, ο‚· Spatial filter, ο‚· Lens, ο‚· Phase plate, ο‚· Infrared camera, ο‚· Laptop (which visualises the camera view). Fig. 2 shows the optical vortex gained at the Institute of Optoelectronics at Military University of Technology . Fig. 2 The Optical Vortex observed at infrared camer 3. Mathematics of Nematic Liquid Crystals Fig. 3 shows the 5CB ne matic molecu le. The e lectrical permeab ility for such ne matic crystal is different for paralle l direction πœ€βˆ₯ to director οΏ½Μ†οΏ½ and different for perpendicular direction πœ€βŠ₯ to director οΏ½Μ†οΏ½. Fig. 3 Nematic 5CB molecule with the marked vectors: parallel and perpendicular to the director 𝑛 The electrical permeability anisotrophy is given by Eq. (1): πœ€π‘Ž = πœ€βˆ₯ βˆ’ πœ€βŠ₯ (1) where: πœ€βŠ₯ – electrical permeability perpendicular to the molecules director, πœ€βˆ₯ – electrical permeability parallel to the molecules director. Proceedings of Engineering and Technology Innovation, vol. 5, 2017, pp. 01 - 06 Copyright Β© TAETI 4 These permeabilities are factors of the continuous med iu m, not of a single mo lecule . If πœ€π‘Ž > 0, then we have a positive liquid crystal anisotropy; if πœ€π‘Ž < 0, the crystal is negative. The ne matic c rystal which is used to form the optical vorte x is a positive liquid crystal. The resultant refractive index of the light is given by Eq. (2): π‘›π‘Ž = 𝑛𝑒 βˆ’ 𝑛0 (2) where: 𝑛0 – the ordinary refractive index of the light, 𝑛𝑒 – the extraordinary refractive index of the light , π‘›π‘Ž – the resultant refractive index of the light. The density of the energy of the interaction of the nematic crystal with the electric field is made by Eq. (3) [7]: 𝑓𝐸 = βˆ’ 1 2 𝐸 β‹… 𝐷 = βˆ’ 1 2 (𝐸βˆ₯ , 𝐸βŠ₯) β‹… (πœ€0 πœ€βˆ₯ 𝐸βˆ₯ , πœ€0 πœ€βŠ₯ 𝐸βŠ₯) = βˆ’ 1 2 πœ€0 (πœ€βˆ₯ 𝐸βˆ₯ 2 + πœ€βŠ₯ 𝐸βŠ₯ 2 ) (3) where: 𝐸 – external electrical field, 𝐷 – electrical induction. The function 𝑓𝐸 depends on the orientation fie ld 𝑛 and its first deriat ive, the electrica l fie ld E is e xc ited in the ne matic crystal by the electrical induction D. The phase shift between the ordinary and extraordinary rays of the light at the exit of ne matic c rystal can be described by the following Eq. (4): πœ‘ = 2πœ‹ πœ† 𝑑 [ 1 𝑑 ∫ 𝑛𝑒 π‘›π‘œ βˆšπ‘›π‘’ 2 βˆ™ 𝑠𝑖𝑛2 πœ—(𝑧) + π‘›π‘œ 2 βˆ™ π‘π‘œπ‘  2 πœ—(𝑧) 𝑑𝑧 βˆ’ π‘›π‘œ 𝑑 0 ] (4) For πœ—(𝑧) = 0 πœ‘ = 2πœ‹ πœ† (𝑛𝑒 βˆ’ π‘›π‘œ )πœ† for πœ—(𝑧) = πœ‹ 2 πœ‘ = 0 We can see, from the above, that if the liquid c rystal molecules are o riented parallel to the phase plate covers, ie. πœ—(𝑧) = 0, then the propagation of light through the liquid crystal is impossible, because the ordinary ray and the e xtraordinary cannot interfe re with each other. When the directors of the liquid crystal mo lecules are angled to the the covers of phase plate - c lose to πœ—(𝑧) = πœ‹ 2 , then propagation of light through the liquid crystal is possible, because the phase shift between the ordinary and the extraordinary ray of light is zero, so the rays can interfere with each other. Depending on the deviation angle πœ—(𝑧) of the liquid crystal mo lecules fro m the covers of phase plate the light phase is delayed from 0 to 2πœ‹ , forming the optical vortex this way. 4. The Concept of Using the Optical Vortex So far, the IOE WAT group performed numerica l analysis of the forming and carrying the optical vortex in the optical fiber. On that basis the vortex forming setup was made. It a llo wed the study of stable spatial structure of optical vorte x in the optical telecommunications . Proceedings of Engineering and Technology Innovation, vol. 5, 2017, pp. 01 - 06 Copyright Β© TAETI 5 In cooperation with the tea m of Dr. Pa weΕ‚ Mergo fro m UM CS in Lub lin, we made mic rostructural fibers appropriate (according to calculations) to carry an optical vortex. Currently the tec hnical study is focused on the correct introducing vortex to a mic rostructural fiber and obtaining a stable and long distance propagation in it. The idea of ma intaining the optical vorte x in a teleco mmun ication fiber is to use it to secure data e xchange. According to our conceptual analysis optical vortices can be used for data protection. Th is applicat ion can be done in various ways by using the specific properties of optical vortices. Adequately to standard fiber optic systems, we reco mmend the use of light intensity changes of an optical vortex as a fiber optic sensor. In addit ion, there is a possibility of modulating the optica l vorte x to falsify positions of bits in space and time so that the reproducing of the information is not possible. Fig. 4 shows schematic concept of using the optical vortex for building safe data transfer system. (a) The optical fiber sensor (b) An information carrier Fig. 4 A simplified diagra m of the concept of using an optical vortex as: a. the optical fiber sensor, b. an information carrier - for an optical encoding; blue color is for the information flow, red is for sensor element In the first case, according to the assumptions, the information b it (h ighlited with a blue line on Fig. 4 a .) propagates in the ma in core of the optical fiber. The optical vorte x (h ighlited with a red line on Fig. 4 a .) p ropagates in the rest of the cores. The ma in core of the fiber is now the main co mmunicat ion channel. The e xte rnal optical fiber cores carry constant or free ly modulated optical vortex light. In the situation of physical violation, the optical fiber the optical vorte x is lea king and mixing with the encoded informat ion. It starts a flow of light energy, which in effect fa lsifies the wiretapping detector. In addition, at the time of disturbance on the output of the mic rostructural fiber, there is being c reated an information noise that goes to main rece ivi ng ele ment. On the basis of this intensity effect, the alarm of attempt of wiretapping the information transmitted in the optical fiber can be generated. In the second case, we use the optical vorte x modulation. Fig. 4(b). shows the concept of using the optical vortex as a modulated information carrier. Optical vorte x, according to the assumptions, can be spatially modulated or time modulated by changing its topology and adjusting its phase delay. This modulation a llo ws encoding information bit on the optical vortex. Spatial-time change of the position of the individual optical bits prevents correct reading it – without building a proper detection system and without access to the en tire structure of the core. Wiretapping with a tradit ional method, eg. by using a clip-on coupler is impossible. Co mpared to known methods of securing the informat ion in the fiber optic trac k, such as interference sensors, QKD systems, these systems bring new types of functional characteristics and they can be used to build secure tracks of classified/confidential data exchange . Proceedings of Engineering and Technology Innovation, vol. 5, 2017, pp. 01 - 06 Copyright Β© TAETI 6 5. Summary We briefly described the idea of the formation and operation of the optical vortex obtained at the Institute of Optoelectronics at Military University of Technology. We a lso showed physics phenomena and mathemat ical description of the changes taking place in the nematic liquid crystals, which are responsible for the formation of an optical vortex. We introduced the concept of using an optical vorte x both to encode information in the optica l fiber trac k and to protect data which is transmitted in this track. As part of the work, we achieved a stable distribution of optical vortex for optical telecommun ications range of the gen erated light - 1550 n m. In addition, we developed and made microstructural optical fiber that is suitable for carry ing vortices and allows imple mentation of the described setup concepts. Our further studies are aimed on a deeper understanding and improving systems using optical vortices to safe information carrying . References [1] N. Bozinovic, β€œOrbital angular momentum in optical fibers ,” Ph.D. dissertation, College of Eng., Boston Univ., United States , 2013. [2] W. Fraczek, β€œInterferometric measurement of optical field phase distribution using the phase discontinuity ,” Ph.D. dissertation, Lower Silesian Digital Library, 2008. [3] R. J. Essiambre and R. W. Tkach, β€œCapacity trends and limits of optical communication networks ,” Proc. of the IEEE, vol. 100, no. 5, pp.1035- 1055, May 2012. [4] C. Brunet and L. A. Rusch, β€œOptical fibers for the transmission of orbital angular momentum modes ,” Optical Fiber Technology, vol. 31, pp. 172-177, September 2016 [5] N. Bozinovic, Y. Yue, Y. Ren, M. Tur, P. Kristensen, H. Huang, et al., β€œTerabit-scale orbital angular momentum mode division multiplexing in fibers ,” Science, vol. 340, no. 6140, pp. 1545-1548, 2013. [6] J. Albero, P. Garcia-Martinez, N. Bennis, E. Oton, B. Cerrolaza, I. Moreno, et al., β€œLiquid crystal devices for the reconfigurable generation of optical vortices,” Journal of Lightwave Technology, vol. 30, no. 18, pp. 3055-3060, 2012. [7] J. KΔ™dzierski, M. A. Kojdecki, Z. Raszewski, J. ZieliΕ„ski, β€œFrederiks transitions and their role in determining material constants of liquid crystals,” Chapter of monograph: Complementary methods in study of condensed phases, p p. 242-271, 2008.