2nd German-West African Conference on Sustainable and Renewable Energy Systems SusRES - Kara 2021 Photovoltaic https://doi.org/10.52825/thwildauensp.v1i.8 © Authors. This work is licensed under a Creative Commons Attribution 4.0 International License Published: 15 June 2021 Evaluation of power losses in a DC-DC Boost converter Komi Boniface EHLAN1, Edjadessamam AKORO 1,2, Hodo-Abalo SAMAH 1, N’detigma KATA1,2, Amadou Séidou MAIGA 2 1 Faculté des Sciences et Techniques (FaST), Université de Kara, Togo 2 Département de Physique Appliquée, Université Gaston Berger, Saint-Louis, Sénégal Abstract. DC-DC converters are dynamic systems consisting of the passive components. These components under the effect of thermal stress in a PV system generate power losses. The knowledge of these power losses is necessary to evaluate the conversion efficiency of the system. Using the polynomial approximation method, the equations for calculating losses in the different components were determined. The system is implemented under the MATLAB / Simulink software. The results show that for a PV application of 240 W supplied to the load, 18% are lost, only 82% are transferred Keywords: Photovoltaic conversion chain, DC-DC converter, Power losses. Introduction Photovoltaic solar energy comes from the direct conversion of solar radiation into electrical energy through Photovoltaic (PV) cells. Depending on the desired power, these cells are connected in series and or in parallel to give a photovoltaic generator (GPV) [1], [2]. Nevertheless, the production of this energy varies according to the light intensity and the temperature of the cell. On the other hand, [3] states that a direct connection of the PV generator to the load does not guarantee the transfer of the maximum available power. In order to extract the maximum power available at each moment at the terminals of the PVG, the technique classically used is the insertion of a matching stage composed of a DC-DC converter and a MPPT (maximum power point tracking) controller between the GPV and the load [2]. The latter acts as an interface between the GPV and the load by ensuring, through a control action, the transfer of the maximum power supplied by the GPV so that it is as close as possible to the maximum available power. Therefore, several works on photovoltaic systems have led to the development of algorithms to extract the maximum energy from the GPV to increase the system efficiency. Therefore, the main objective of this paper is to shed light on the different losses generated by a converter in a PV conversion chain. To do this, we have based ourselves on the polynomial approximation method and on the manufacturer’s, data sheets to derive the equations of the losses as a function of the global current. In order to confirm our theory, we proceeded by programming these equations under the MATLAB / Simulink software. The rest of the paper is organized as follows: the block diagram of the studied PV conversion chain is described in section 2 and the loss equations are established in section 3. Section 4 presents the discussions on the obtained results and section 5 concludes the paper. 13 https://creativecommons.org/licenses/by/4.0/ https://creativecommons.org/licenses/by/4.0/ Ehlan et al. | TH Wildau Eng. Nat. Sci. Proc.1 (2021) “SusRES 2021” Synoptic diagram of a PV conversion chain connected to a DC load A photovoltaic system consists of four (04) blocks as shown in Figure 2. The first block represents the energy source (PV panel), the second block is a static DC-DC converter, the third block represents the load and the fourth block represents the control system. This MPPT control system is in charge of modifying the cyclic ratio of the converter's switching cell in order to force the panel to deliver the maximum of its energy at each moment. Figure 1: Synoptic diagram of the photovoltaic system Global study of the losses for a static converter As described in the previous section, the constituents of the Boost converter are: MOSFET, Diode, Inductance and Capacitance. The conversion efficiency can be written as: 𝛈𝐂𝐨𝐧𝐯𝐞𝐫𝐬𝐢𝐨𝐧 = 𝐏𝐨𝐮𝐭 𝐏𝐢𝐧 = 𝐏𝐢𝐧−𝐏𝐥𝐨𝐬𝐬𝐞𝐬 𝐏𝐢𝐧 (1) With 𝑃𝑖𝑛 and 𝑃𝑜𝑢𝑡 the powers respectively at the input and output of the converter, 𝑃𝑙𝑜𝑠𝑠𝑒𝑠 the power lost in the converter Losses in the MOSFET The transistor dissipates energy during the firing phase WA, the conduction phase WC, and the blocking phase WB corresponding to a Total energy WT: per switching period. For a MOSFET, the behavior in conduction regime is similar to that of a resistor, the powers dissipated during this phase and during the switching phases are defined according to [4] by the following equations: PCond = 𝑓. W𝐶𝑜𝑛𝑑 = TCond T . Von. Iin = α. I²in. RDSon (2) PCond = (WA + WB). 𝑓 = 1 2 . Vin. Iin(𝑡𝑐𝑜𝑚 + 𝑡𝐵𝑙𝑜𝑐 )𝑓 + 1 2 . Vin. IRM. 𝑓. 𝑡𝑐𝑜𝑚 (3) With : WA: Energy dissipated during the firing phase, WB: Energy dissipated during the blocking phase, W𝐶𝑜𝑛𝑑: Energy dissipated during the conduction phase, WT: Total energy dissipated by the MOSFET, RDSon: Source drain resistance of the MOSFET, Vin∶ Voltage at the terminals of the transistor in the blocked state, Iin : current delivered by the generator, IRM: amplitude of the diode's overlay current, 𝛂: the duty cycle, 𝑓: the switching frequency of the MOSFET, 𝑡𝑐𝑜𝑚: duration of the switching phase, and𝒕𝑩𝒍𝒐𝒄: duration of the blocking phase. In summary, the total losses at the MOSFET can be evaluated by: 𝐏 = 𝒇. 𝐖𝐓 = 𝛂. 𝐈²𝐢𝐧. 𝐑𝐃𝐒𝐨𝐧 + 𝟏 𝟐 . 𝐕𝐢𝐧. 𝐈𝐢𝐧(𝒕𝒄𝒐𝒎 + 𝒕𝑩𝒍𝒐𝒄)𝒇 + 𝟏 𝟐 . 𝐕𝐢𝐧. 𝐈𝐑𝐌. 𝒇. 𝒕𝒄𝒐𝒎 (4) 14 Ehlan et al. | TH Wildau Eng. Nat. Sci. Proc.1 (2021) “SusRES 2021” Losses in the diode When the diode is blocked, it behaves like a perfect capacitor because there is virtually no current flowing through it and only the voltage across it varies. When it is on, the voltage and the current vary. The other losses of the diode have been taken into account in the switching losses of the MOSFET, only the conduction losses are considered here. These are in the form of: 𝑃𝐹 = 𝑉𝑑 . 𝐼𝑜𝑢𝑡 with 𝑉𝑑 = 𝑅𝑑 . 𝐼𝑖𝑛 + 𝑉𝐹 (5) 𝐏𝐅 = (𝟏 − 𝛂) [𝐑𝐝. 𝐈²𝐢𝐧 + 𝐈𝐢𝐧. 𝐕𝐅 ] (6) with 𝑅𝑑 : differential resistance or dynamic resistance et 𝑉𝐹 : direct voltage. Losses in the capacitor In most cases, a capacitor is a simple capacitance C expressed in Farad but as a component the capacitor is not limited to its simple capacity: 𝐏𝐂𝐚𝐩 = 𝐑𝐂. 𝑰𝑹𝑴𝑺 𝟐 (7) We can rewrite (7) thanks to the expressions of the effective currents in the various components of the circuit developed in [5] in the form: 𝐏𝐜𝐚𝐩𝐚𝐜𝐢𝐭𝐨𝐫 = 𝐑𝐜𝛂(𝟏 − 𝜶)𝐈𝐢𝐧 𝟐 + 𝑹𝒄 𝟏𝟐 (𝟏 − 𝛂) ( 𝛂∗𝐕𝐢𝐧 𝐋∗𝐟 ) 𝟐 (8) Losses in the inductor The equivalent electrical model of a wound inductor can be reduced to an ideal inductor in series with a resistor RL. The presence of the latter generates direct losses by Joule effect linked to the conductors and to the losses induced in the magnetic core (losses by hysteresis and by eddy currents) which depend on the frequency and the variation of the flux. 𝐏𝐈𝐧𝐝𝐮𝐜𝐭𝐨𝐫 = RL. IL,RMS 2 (9) 𝐏𝐈𝐧𝐝𝐮𝐜𝐭𝐨𝐫 = 𝐑𝐋𝐈𝐢𝐧 𝟐 + 𝐑𝐋 𝟏𝟐 ( 𝛂∗𝐕𝐢𝐧 𝐟∗𝐋 ) 𝟐 (10) The expressions (11) and (12) of the average voltage of the inductance and the average current of the capacitor of a boost converter, make it possible to establish a relation showing the influence of the losses generated by RL of the inductance on the output of this converter according to the electric quantities of the circuit [6]. 〈𝑉𝐿 〉 = 0 = 𝑉𝑖𝑛 − 𝑅𝐿 𝐼𝑖𝑛 − (1 − 𝛼). 𝑉 (11) 〈𝑖𝐶 〉 = 0 = (1 − 𝛼). 𝐼𝑖𝑛 − 𝑉 𝑅 (12) 𝛈 = 𝐏𝐨𝐮𝐭 𝐏𝐢𝐧 = 𝟏 𝟏+ 𝐑𝐋 𝐑.𝛂′² (13) For application, we used a MOSFET type IRFZ44E [7], a Standard silicon rectifier diodes1N 5059...1N 5062 [8], a capacitor APSA100ESS680MFA5S [9] and an inductor muRata|Ps 49101sc [10]. Using the datasheets of all these components, the equations for calculating the losses as a function of the current through them are summarized in Table 1. 15 Ehlan et al. | TH Wildau Eng. Nat. Sci. Proc.1 (2021) “SusRES 2021” Table 1: Loss evaluation equations Parameters Equations 𝐏𝐌𝐨𝐬𝐟𝐞𝐭 (𝟖. 𝟔𝟐𝟓𝒆−𝟑)𝑰𝒊𝒏 𝟐 + (𝟎. 𝟐𝟑𝟒)𝑰𝒊𝒏 + 𝟑𝟒. 𝟓𝟑𝒆 −𝟑 𝐏𝐃𝐢𝐨𝐝𝐞 (𝟐. 𝟓𝟔𝟐𝐞−𝟐)𝐈𝐢𝐧 𝟐 + 𝟎. 𝟔𝟖𝟖𝐈𝐢𝐧 𝐏𝑪𝒂𝒑𝒂𝒄𝒊𝒕𝒐𝒓 (𝟓. 𝟖𝟔𝐞−𝟑)𝐈𝐢𝐧 𝟐 + 𝟎. 𝟎𝟕𝟑𝟐 𝐏𝑰𝒏𝒅𝒖𝒄𝒕𝒐𝒓 (𝟎. 𝟏𝟔𝟓)𝐈𝐢𝐧 𝟐 + 𝟎. 𝟗𝟑𝟖 Loss calculation method From the equations listed in Table 1, the block model in Figure 2 has been developed in Simulink to calculate the losses generated by a single-inverter PV system. Each of its blocks modeling the losses whose sum represents the total loss of the converter receives at its input the current 𝑰𝒊𝒏 which is the equivalence of the current 𝑰𝑷𝑽. This calculation block is associated with the MPPT control system that is implemented in the converter. Figure 2: Total loss calculation blocks of a DC-DC converter in a PV system. Results and discussions We have evaluated the losses in the components including the switching cells (MOSFET, diode) and passive components of a DC-DC converter. On figure 3 showing the characteristic curves of the losses generated by these components as a function of the global current, we can notice that the losses in the capacitor, the MOSFET and in the diode are almost linear while the losses in the inductor evolve exponentially with the global current. In terms of efficiency, a cross analysis between figure 3 and 4 shows that the influence of these losses on the conversion efficiency is directly proportional to the losses generated by each component of the converter. 16 Ehlan et al. | TH Wildau Eng. Nat. Sci. Proc.1 (2021) “SusRES 2021” Figure 3: Changes in losses based on global current Figure 4: Influence of losses on efficiency 17 Ehlan et al. | TH Wildau Eng. Nat. Sci. Proc.1 (2021) “SusRES 2021” Figure 5: Loss distribution diagram Figure 6: Total loss diagram. Then, the simulation is performed under MATLAB / Simulink with a 240 KW PV generator and a purely resistive charge of 9.6 Ω. By applying the Figure 1 loss calculation block, Figure 6 shows that for a 240W PV source, a converter can encroach on conversion output up to 18% of the total power available at its in, reducing conversion power to 82%. Figure 5 shows that 53% of its losses are caused by the inductor, 33% by the diode, 11% by the MOSFET and only 2% by the capacitor. Conclusion The total efficiency of the converter is strongly influenced by the efficiency of the induction since the efficiency of the capacitor and MOSFET always remain above 95% and 90% respectively. While the efficiency of the diode which is 67% is still acceptable, the induction seems to impose its losses on the converter we simulated. Thus, in order to boost the efficiency of the converter, we must try to work a lot on the effectiveness of the inductor. ACKNOWLEDGEMENTS The authors offer their sincere thanks to the German Academic Exchange Service DAAD through the Technical University of Applied Sciences (WILDAU) for their unwavering support throughout the implementation of this work. References [1] Dileep G, Singh S. Selection of non-isolated DC-DC converters for solar photovoltaic system. Renewable and Sustainable Energy Reviews. 2017 Sep;76:1230-1247. https://doi.org/10.1016/j.rser.2017.03.130 [2] Azab M. A new maximum power point tracking for photovoltaic systems. World Academy of Science, Engineering and Technology. 2008;44:571–574. [3] Akoro E, Gabriel Jean-Philippe T, Faye M, Doumbia M, Amadou SM. Artificial Neural Network Photovoltaic Generator Maximum Power Point Tracking Method using Synergetic 18 https://doi.org/10.1016/j.rser.2017.03.130 Ehlan et al. | TH Wildau Eng. Nat. Sci. Proc.1 (2021) “SusRES 2021” Control Algorithm. Akoro et al.,International Journal on Emerging Technologies11(2): 590- 594(2020) 590International Journal on Emerging Technologies . 2020;11(2):590–594. [4] Cabal C. Optimisation énergétique de l'étage d'adaptation électronique dédié à la conversion photovoltaïque.:188. [5] Walker G. Evaluating MPPT converter topologies using a Matlab PV model. Australian Journal of Electrical & Electronics Engineering. 2001;21(1):49-55. [6] Erickson RW. Fundamentals of power electronics. New York: Chapman & Hall; 1997. [7] IRFZ44E MOSFET Datasheet pdf - Equivalent. Recherche de références croisées. https://alltransistors.com/mosfet/transistor.php?transistor=3395. Accessed 2021 March 27. [8] 1N 5059...1N 5062. https://www.terraelectronica.ru/pdf/show?pdf_file=%252Fz%252FDatasheet%252F1%252F1 N5061.pdf. Accessed 2021 March 27. [9] Cha E. PART NUMBERING SYSTEM, p.2. [10] Magnetic Products, p. 20. M. P. Solutions; 19 https://alltransistors.com/mosfet/transistor.php?transistor=3395 https://www.terraelectronica.ru/pdf/show?pdf_file=%252Fz%252FDatasheet%252F1%252F1N5061.pdf https://www.terraelectronica.ru/pdf/show?pdf_file=%252Fz%252FDatasheet%252F1%252F1N5061.pdf 3_8-Ehlan_etal_Conference paper-31-1-6-20210510 Leere Seite